Niles Audio SW10JM, SW10WM manual Preparing the cabinet, Installing the cabinet, Top Bottom

Page 26

Top

2b.Determine suitable wire routing method. The SW10WM is provided with terminal cups at both the bottom and top of the unit for convenience.

Top

Bottom

Preparing the cabinet

3a.Remove the large bolts located at the top of the cabinet and ﬂip the brackets over re-installing brackets with the same bolts, leaving them loose. Ensure the ﬂange surface with 4 holes is above the cabinet. Allow access for the installation hardware.

3b.Locate the feet inside the pre-construction package. Place feet on cabinet.

Installing the cabinet

4. Place subwoofer cabinet into stud bay and adjust brackets to accommodate the exact width of construction. Tighten the bolts.

(CONTINUED ON NEXT PAGE)

24

Image 26

Contents A N D N I L E S S W 1 0 W M WA L L M O U N T S U B W O O F E R SW10JM SW10WMFOR USE WITH NILES SW10JM JOIST MOUNT SUBWOOFER SW10JM Placement TABLE OF CONTENTSCONGRATULATIONS SW10JM In-ceiling/In-floor installationINTRODUCTION SW10JM JOIST MOUNT SUBWOOFER SW10WM WALL MOUNT SUBWOOFER10-INCH WOOFER WITH INJECTION MOLDED TCC SW10JM ONLY INSTALLATION FLEXIBILITYFEATURES AND BENEFITS 10-INCH REINFORCED FIBERGLASS CONE WOOFER SW10WM ONLYQUALITY YOU CAN COUNT ON NILES SW10JM JOIST MOUNT SUBWOOFERTOOLS NEEDED SW10JM PLACEMENT Figure 2. Home Theater layout with SW10JM placement optionsSW10JM IN-CEILING/IN-FLOOR INSTALLATION Pre-ConstructionFloor SW10JM INSTALLATION - FLOOR APPLICATIONFLOOR APPLICATION - BEFORE FINAL FLOORING APPLIED Subwoofer Rear Bracket SubwooferFront Bracket 2 x ScrewsSW10JM INSTALLATION - FLOOR APPLICATION CONTINUED staple the template in place for added ease FLOOR APPLICATION - COMPLETE INSTALLATIONNew/Existing Construction CONTINUED ON NEXT PAGEFront Bracket 7. Install the included ﬂoor grille into the cut-out opening using the supplied screwsSW10JM INSTALLATION - CEILING APPLICATION CEILING APPLICATION - BEFORE DRYWALL APPLIED Pre-Construction4. Place the SW10JM subwoofer into the brackets 7. For trim out, remove Trim Out Panel SW10JM INSTALLATION - CEILING APPLICATION CONTINUED9. Install the included ceiling grille into the frame CEILING APPLICATION - COMPLETE INSTALLATION New/Existing Construction SW10JM INSTALLATION - CEILING APPLICATION CONTINUED 8. Install the included ceiling grille into the frame AMPLIFIER REQUIREMENTS & WIRING OptionalWIRING FOR NEW CONSTRUCTION The SW10JM has 5-way binding posts that accept all types of wire endsThe SW10WM Wall Mount subwoofer includes the following items SW10WM WALL MOUNT SUBWOOFERInstallation package Preconstruction packageSW10WM PLACEMENT Figure 6. Possible home theater layout with SW10WM placement optionsSW10WM IN-WALL INSTALLATION Pre-ConstructionTop Bottom Installing the cabinetPreparing the cabinet SW10WM IN-WALL INSTALLATION CONTINUED Installation Package13. Insert the metal grille into the frame pressing ﬁrmly all the way around the perimeterFigure 7. 1 or more SW10WM connected to the SWA-500 Figure 8. 5-way binding postsSPECIFICATIONS SOLUTIONS TROUBLESHOOTING GUIDEPROBLEM Page NILES AUDIO CORPORATION - 1-800-BUY-HIFI or 1 2 3 3 1 S . W . 1 3 0 S t r e e t M i a m i , F l o r i d a 3 3 B L E N D I N G H I G H F I D E L I T Y A N D A R C H I T E C T U R EN i l e s A u d i o C o r p o r a t i o n 1 - 3 0 5 - 2 3 8 - 4