Niles Audio SW10WM manual SW10JM INSTALLATION - CEILING APPLICATION CONTINUED

Page 19

SW10JM INSTALLATION – CEILING APPLICATION (CONTINUED)

4. Attach the supplied front and rear brackets to the 2 x 4’s using the supplied 1.5" screws.

NOTE: REMOVE THE STOP BLOCK FROM THE SW10JM PORT THE STOP BLOCK IS INCLUDED TO PREVENT THE SUBWOOFER FROM DISENGAGING FROM BRACKETS UNTIL THE GRILLE IS INSTALLED.

Screws Rear Bracket

Front Bracket 2 x 4

2 x 4

5. Place the SW10JM subwoofer into the brackets

aligning the attachment pins to the slots in the
brackets. Begin with the ported end ﬁrst.			Subwoofer

Front Bracket	Subwoofer	Rear Bracket

Screw

Stop Block

6. Install the stop block between the bracket and cabinet at rear of cabinet as indicated in drawing.

Screw
Subwoofer
Stop Block
NILES AUDIO CORPORATION – 1-800-BUY-HIFI or 1-305-238-4373		17

Image 19

Contents FOR USE WITH NILES SW10JM JOIST MOUNT SUBWOOFER SW10JM SW10WMA N D N I L E S S W 1 0 W M WA L L M O U N T S U B W O O F E R SW10JM In-ceiling/In-floor installation TABLE OF CONTENTSCONGRATULATIONS SW10JM PlacementSW10JM JOIST MOUNT SUBWOOFER SW10WM WALL MOUNT SUBWOOFER INTRODUCTION10-INCH REINFORCED FIBERGLASS CONE WOOFER SW10WM ONLY INSTALLATION FLEXIBILITYFEATURES AND BENEFITS 10-INCH WOOFER WITH INJECTION MOLDED TCC SW10JM ONLYNILES SW10JM JOIST MOUNT SUBWOOFER QUALITY YOU CAN COUNT ONTOOLS NEEDED Figure 2. Home Theater layout with SW10JM placement options SW10JM PLACEMENTSW10JM IN-CEILING/IN-FLOOR INSTALLATION FLOOR APPLICATION - BEFORE FINAL FLOORING APPLIED SW10JM INSTALLATION - FLOOR APPLICATIONPre-ConstructionFloor 2 x Screws SubwooferFront Bracket Subwoofer Rear BracketSW10JM INSTALLATION - FLOOR APPLICATION CONTINUED CONTINUED ON NEXT PAGE FLOOR APPLICATION - COMPLETE INSTALLATIONNew/Existing Construction staple the template in place for added easeSubwoofer Rear Bracket cut-out opening using the supplied screws 7. Install the included ﬂoor grille into theCEILING APPLICATION - BEFORE DRYWALL APPLIED Pre-Construction SW10JM INSTALLATION - CEILING APPLICATION4. Place the SW10JM subwoofer into the brackets 9. Install the included ceiling grille into the frame SW10JM INSTALLATION - CEILING APPLICATION CONTINUED7. For trim out, remove Trim Out Panel CEILING APPLICATION - COMPLETE INSTALLATION New/Existing Construction SW10JM INSTALLATION - CEILING APPLICATION CONTINUED 8. Install the included ceiling grille into the frame Optional AMPLIFIER REQUIREMENTS & WIRINGThe SW10JM has 5-way binding posts that accept all types of wire ends WIRING FOR NEW CONSTRUCTIONPreconstruction package SW10WM WALL MOUNT SUBWOOFERInstallation package The SW10WM Wall Mount subwoofer includes the following itemsFigure 6. Possible home theater layout with SW10WM placement options SW10WM PLACEMENTPre-Construction SW10WM IN-WALL INSTALLATIONPreparing the cabinet Installing the cabinetTop Bottom Installation Package SW10WM IN-WALL INSTALLATION CONTINUEDﬁrmly all the way around the perimeter 13. Insert the metal grille into the frame pressingFigure 8. 5-way binding posts Figure 7. 1 or more SW10WM connected to the SWA-500SPECIFICATIONS PROBLEM TROUBLESHOOTING GUIDESOLUTIONS Page NILES AUDIO CORPORATION - 1-800-BUY-HIFI or 1 - 3 0 5 - 2 3 8 - 4 B L E N D I N G H I G H F I D E L I T Y A N D A R C H I T E C T U R EN i l e s A u d i o C o r p o r a t i o n 1 2 3 3 1 S . W . 1 3 0 S t r e e t M i a m i , F l o r i d a 3 3