Niles Audio SW10JM SW10WM WALL MOUNT SUBWOOFER, Preconstruction package, Installation package

Page 23

SW10WM (WALL MOUNT) SUBWOOFER

SW10WM (WALL MOUNT) SUBWOOFER

The SW10WM Wall Mount subwoofer includes the following items:

Preconstruction package:

•1 Ported cabinet (back box) with trim-out panel

•1 set of installation brackets with screws

•1 set of rubber feet

	Installation package:
	• 1	Baffle mounted passive driver
	• 1	MicroPerf™ grille with frame
	• 1 Template for subwoofer placement
	TOOLS NEEDED:
	• Pencil		Figure 5.
	• Drywall saw		Figure 5.
	• Drywall saw		Niles SW10WM Wall Mount Subwoofer

•Phillips screwdriver

•Drill (and assorted bits)

•Wire strippers

•Tape measure

•Level (optional)

•Awl (optional)

•Staple gun (optional)

•Protective safety gear

•Tools suitable for cutting opening in the applicable flooring/wall material

CAUTION: ALWAYS CHECK FOR ELECTRICAL, HEATING, PLUMBING, CONDUIT, ETC., BEFORE CUTTING INTO CEILINGS OR FLOORS.

NILES AUDIO CORPORATION – 1-800-BUY-HIFI or 1-305-238-4373		21

Image 23

Contents A N D N I L E S S W 1 0 W M WA L L M O U N T S U B W O O F E R SW10JM SW10WMFOR USE WITH NILES SW10JM JOIST MOUNT SUBWOOFER SW10JM In-ceiling/In-floor installation TABLE OF CONTENTSCONGRATULATIONS SW10JM PlacementSW10JM JOIST MOUNT SUBWOOFER SW10WM WALL MOUNT SUBWOOFER INTRODUCTION10-INCH REINFORCED FIBERGLASS CONE WOOFER SW10WM ONLY INSTALLATION FLEXIBILITYFEATURES AND BENEFITS 10-INCH WOOFER WITH INJECTION MOLDED TCC SW10JM ONLYNILES SW10JM JOIST MOUNT SUBWOOFER QUALITY YOU CAN COUNT ONTOOLS NEEDED Figure 2. Home Theater layout with SW10JM placement options SW10JM PLACEMENTSW10JM IN-CEILING/IN-FLOOR INSTALLATION Pre-ConstructionFloor SW10JM INSTALLATION - FLOOR APPLICATIONFLOOR APPLICATION - BEFORE FINAL FLOORING APPLIED 2 x Screws SubwooferFront Bracket Subwoofer Rear BracketSW10JM INSTALLATION - FLOOR APPLICATION CONTINUED CONTINUED ON NEXT PAGE FLOOR APPLICATION - COMPLETE INSTALLATIONNew/Existing Construction staple the template in place for added easeSubwoofer Rear Bracket cut-out opening using the supplied screws 7. Install the included ﬂoor grille into theCEILING APPLICATION - BEFORE DRYWALL APPLIED Pre-Construction SW10JM INSTALLATION - CEILING APPLICATION4. Place the SW10JM subwoofer into the brackets 7. For trim out, remove Trim Out Panel SW10JM INSTALLATION - CEILING APPLICATION CONTINUED9. Install the included ceiling grille into the frame CEILING APPLICATION - COMPLETE INSTALLATION New/Existing Construction SW10JM INSTALLATION - CEILING APPLICATION CONTINUED 8. Install the included ceiling grille into the frame Optional AMPLIFIER REQUIREMENTS & WIRINGThe SW10JM has 5-way binding posts that accept all types of wire ends WIRING FOR NEW CONSTRUCTIONPreconstruction package SW10WM WALL MOUNT SUBWOOFERInstallation package The SW10WM Wall Mount subwoofer includes the following itemsFigure 6. Possible home theater layout with SW10WM placement options SW10WM PLACEMENTPre-Construction SW10WM IN-WALL INSTALLATIONTop Bottom Installing the cabinetPreparing the cabinet Installation Package SW10WM IN-WALL INSTALLATION CONTINUEDﬁrmly all the way around the perimeter 13. Insert the metal grille into the frame pressingFigure 8. 5-way binding posts Figure 7. 1 or more SW10WM connected to the SWA-500SPECIFICATIONS SOLUTIONS TROUBLESHOOTING GUIDEPROBLEM Page NILES AUDIO CORPORATION - 1-800-BUY-HIFI or 1 - 3 0 5 - 2 3 8 - 4 B L E N D I N G H I G H F I D E L I T Y A N D A R C H I T E C T U R EN i l e s A u d i o C o r p o r a t i o n 1 2 3 3 1 S . W . 1 3 0 S t r e e t M i a m i , F l o r i d a 3 3