Niles Audio SW10JM manual SW10WM IN-WALL INSTALLATION CONTINUED, Installation Package

Page 27

SW10WM IN-WALL INSTALLATION (CONTINUED)

SW10WM IN-WALL INSTALLATION (CONTINUED)

5. Secure the brackets to the studs using the provided hardware.

6. Make necessary wire connections to terminal cups

NOTE: THE SW10WM CABINET HAS THE

NECESSARY TRIMOUT PANEL ALREADY

INSTALLED. THIS WILL ALLOW SHEETROCK

INSTALLERS THE EXACT LOCATION FOR

CUTTING THE FRAME OPENING AND PREVENT

DEBRIS FROM ENTERING THE CABINET DURING

THE FINAL PHASES OF CONSTRUCTION.

Installation Package

8. Remove Trim Out Panel from the cabinet and discard.

9. Remove the Bafﬂe/Driver from its packaging.

10. Connect the appropriate speaker wires from inside the cabinet to the Push terminal on the back of the subwoofer basket. If using the terminal cups at the top, use the top wires. If using the terminal cups at the button, use the button wires.

11. Insert the Bafﬂe/Driver into the hole securing the bafﬂe in place with the supplied screws.

NILES AUDIO CORPORATION – 1-800-BUY-HIFI or 1-305-238-4373		25

Image 27

Contents SW10JM SW10WM FOR USE WITH NILES SW10JM JOIST MOUNT SUBWOOFERA N D N I L E S S W 1 0 W M WA L L M O U N T S U B W O O F E R SW10JM In-ceiling/In-floor installation TABLE OF CONTENTSCONGRATULATIONS SW10JM PlacementSW10JM JOIST MOUNT SUBWOOFER SW10WM WALL MOUNT SUBWOOFER INTRODUCTION10-INCH REINFORCED FIBERGLASS CONE WOOFER SW10WM ONLY INSTALLATION FLEXIBILITYFEATURES AND BENEFITS 10-INCH WOOFER WITH INJECTION MOLDED TCC SW10JM ONLYNILES SW10JM JOIST MOUNT SUBWOOFER QUALITY YOU CAN COUNT ONTOOLS NEEDED Figure 2. Home Theater layout with SW10JM placement options SW10JM PLACEMENTSW10JM IN-CEILING/IN-FLOOR INSTALLATION SW10JM INSTALLATION - FLOOR APPLICATION FLOOR APPLICATION - BEFORE FINAL FLOORING APPLIEDPre-ConstructionFloor 2 x Screws SubwooferFront Bracket Subwoofer Rear BracketSW10JM INSTALLATION - FLOOR APPLICATION CONTINUED CONTINUED ON NEXT PAGE FLOOR APPLICATION - COMPLETE INSTALLATIONNew/Existing Construction staple the template in place for added easeSubwoofer Rear Bracket cut-out opening using the supplied screws 7. Install the included ﬂoor grille into theCEILING APPLICATION - BEFORE DRYWALL APPLIED Pre-Construction SW10JM INSTALLATION - CEILING APPLICATION4. Place the SW10JM subwoofer into the brackets SW10JM INSTALLATION - CEILING APPLICATION CONTINUED 9. Install the included ceiling grille into the frame7. For trim out, remove Trim Out Panel CEILING APPLICATION - COMPLETE INSTALLATION New/Existing Construction SW10JM INSTALLATION - CEILING APPLICATION CONTINUED 8. Install the included ceiling grille into the frame Optional AMPLIFIER REQUIREMENTS & WIRINGThe SW10JM has 5-way binding posts that accept all types of wire ends WIRING FOR NEW CONSTRUCTIONPreconstruction package SW10WM WALL MOUNT SUBWOOFERInstallation package The SW10WM Wall Mount subwoofer includes the following itemsFigure 6. Possible home theater layout with SW10WM placement options SW10WM PLACEMENTPre-Construction SW10WM IN-WALL INSTALLATIONInstalling the cabinet Preparing the cabinetTop Bottom Installation Package SW10WM IN-WALL INSTALLATION CONTINUEDﬁrmly all the way around the perimeter 13. Insert the metal grille into the frame pressingFigure 8. 5-way binding posts Figure 7. 1 or more SW10WM connected to the SWA-500SPECIFICATIONS TROUBLESHOOTING GUIDE PROBLEMSOLUTIONS Page NILES AUDIO CORPORATION - 1-800-BUY-HIFI or 1 - 3 0 5 - 2 3 8 - 4 B L E N D I N G H I G H F I D E L I T Y A N D A R C H I T E C T U R EN i l e s A u d i o C o r p o r a t i o n 1 2 3 3 1 S . W . 1 3 0 S t r e e t M i a m i , F l o r i d a 3 3