Bryant SYSTXBBUIZ01 Selecting Electric Heater, Equipment Summary, Selecting Accessories

NOTE: Range of outdoor unit Btu selection is limited by model number of indoor unit installed. The Evolution Zone Control™ will not allow an outdoor unit size that is not supported by the installed indoor unit.

NOTE: On new system installations, the model and serial number will be recognized and displayed. On any indoor/outdoor board replacements, the equipment will be recognized but the exact model/serial number will not be displayed.

C. Section 3 — Selecting Electric Heater

ELECTRIC HEATER

NOT IDENTIFIED

ENTER SIZE:		5 KW
NONE, 5,10,15 KW
PRESS +/- TO MAKE
	SELECTION
BACK	CONTINUE

A03197

Fig. 17—Selecting Electric Heater

E. Section 5 — Zoning

ZONING		ZONING
	ZONE 1	UI
SEARCHING FOR	ZONE 2	RS
	ZONE 3	RS
ZONE EQUIPMENT	ZONE 4	RS
WORKING
	UI=USER INTERFACE
	RS=REMOTE SENSOR
	SS=SMART SENSOR
	BACK	CONTINUE

Fig. 18a — Zoning

A04084

SEARCHING FOR ZONE EQUIPMENT will appear on the screen to identify the number of zones detected. This screen will show Zone 1, Zone 2, etc. and indicate all zones having either a remote room sensor, or smart sensors associated with them. If the system contains smart sensors, they must be assigned a zone number before continuing. See Smart Sensor Installation Instruc- tions on how to assign Smart Sensors to their respective zones. When finished, press right-side button to continue. See Fig. 18a.

F. Section 6 — Equipment Summary

If indoor unit is a fan coil and the electric heater is not self-identifying, ″ELECTRIC HEATER NOT IDENTIFIED″ will appear (See Fig. 17). Press either Time or Temp +/- buttons to select appropriate size of electric heater installed, then press right-side button to continue.

NOTE: Range of electric heaters available is limited by model number of the fan coil installed. The Evolution Zone Control™ will not allow an electric heater size that is not supported by the installed fan coil.

EQUIPMENT SUMMARY

FURNACE	355MAV0420
AC	598BNX024
FILTER	EAC
HUMIDIFIER	YES
UV LIGHTS	YES
ZONES	12345678

NOYES

SETUP

COMPLETE!

SAVE

ALL SELECTIONS/

NOYES

A04109

D. Section 4 — Selecting Accessories

Once the indoor and outdoor equipment have been found or entered, the following screens will appear allowing the Installer to select the AIR FILTER TYPE; HUMIDIFIER INSTALLED; and UV LIGHTS INSTALLED″ (See Fig. 18). Use either Time or Temp +/- buttons to make appropriate selections in the highlighted area on the display screen. Press right-side button to continue (or advance) to the next screen.

AIR FILTER TYPE— This accessory screen will appear first. The installer will need to enter the type of filter (MEDIA, EAC, or both). See Table 1 and make a selection using Time or Temp +/- button, then press right-side button to continue.

Table 1 — Filter Selection

INSTALLED FILTER	MENU SELECTION
1 Inch to 4 inch media	MEDIA
High voltage EAC	EAC
High voltage EAC + 1 to 4 inch media	MEDIA + EAC

HUMIDIFIER INSTALLED — This will appear after the Air Filter Type screen. Select whether a humidifier is installed on the system, YES or NO, then press right-side button to continue.

UV LIGHTS INSTALLED— This screen will appear to select

ACCESSORIES		ACCESSORIES			ACCESSORIES
AIR FILTER TYPE:		HUMIDIFIER			U.V. LIGHTS
EAC	EAC	INSTALLED?			INSTALLED?
				YES			YES
MEDIA
MEDIA + EAC
PRESS +/- TO MAKE		PRESS +/- TO MAKE			PRESS +/- TO MAKE
SELECTION		SELECTION			SELECTION
CONTINUE		BACK	CONTINUE		BACK	CONTINUE
AIR FILTER MEDIA TYPE		HUMIDIFIER INSTALLED?			U.V. LIGHTS INSTALLED?

A03198

Fig. 18—Accessories — UV Lights

whether UV lights are installed on the system, select YES or NO, then press right-side button to continue.

—6—

Fig. 19—Equipment Summary

The ″EQUIPMENT SUMMARY″ screen will appear after Ac- cessories and Zoning have been selected. This screen will give a summary of all equipment automatically found or manually selected. If a wrong selection was made, press left-side button (BACK selection) to go back to that particular screen and make changes. When everything is OK, press right-side button again to continue. (See Fig. 19)

The ″SETUP COMPLETE! SAVE ALL SELECTIONS?″ screen will appear after Equipment Summary. To Save All Selections press (YES) right-side button. Pressing the left-side button (NO selection) will return to the Equipment Summary screen where changes can be performed to any of the equipment selection screens. After selecting YES, the initial power up sequence of the new Evolution Zone™ Control is complete. The User Interface screen will now display normal operating mode.

G. Section 7 — Duct Assessment

The following screen will appear after Setup is exited. Press right-side button to start Duct Assessment. Duct Assessment will measure the relative size of the ductwork, including damper leakage. These measurements are used to control the correct amount of airflow in the zoned system. Status messages will appear on the screen to indicate what the system is doing. The process will take approximately one minute per zone. At the end of the process, the display will show the relative size of each zone duct. See Fig. 19a.

DUCT ASSESSMENT		DUCT ASSESSMENT		DUCT ASSESSMENT
MEASURE DUCT		ASSESSMENT ACTIVE
CAPACITY FOR EACH			PLEASE WAIT	ZONE	CAPACITY
	ZONE.	OPENING ALL ZONES		ZONE1	25
		AIRFLOW STABILIZING		ZONE 2	20
				ZONE 3	25
4 MINUTES ARE REQUIRED			PROGRESS	ZONE 4	20
TO COMPLETE				DAMPER LEAKAGE 10
PRESS START TO BEGIN
		STOP
QUIT	START			QUIT	START

Fig. 19a — Duct Assessment

A04085