LG Electronics 1003C operation manual Care and OPERATI0N

Page 14

CARE AND OPERATI0N

ASH DRAWER

The large ash drawer located on the left side of the ped- estal is designed to make cleaning easier by containing the ashes in a removable drawer.

Ash

Drawer

WARNING: DO NOT OPERATE THIS STOVE WITHOUT THE ASH DRAWER PROPERLY INSTALLED AND SE- CURED (SEALED), AS THIS WILL PRODUCE EX- TREME TEMPERATURES, RESULTING IN OVERFIR- ING. THE ASH DRAWER GASKET PROVIDES AN IM- PORTANT SEAL, AND MUST BE MAINTAINED (SEE MAINTENANCE REQUIREMENTS ON PAGE 19). OVERFIRING CAN RESULT IN DAMAGE TO THE AP- PLIANCE OR A HOUSE FIRE. OPERATION WITH THE ASH DRAWER OPEN OR AJAR, NULLIFIES THE SAFETY LISTING AND VOIDS THE WARRANTY.

CATALYTIC COMBUSTOR

How it works: From 5 to 30 percent of the chemical en- ergy contained in every log escapes up the chimney when wood is burned in a conventional stove. The cata- lytic combustor is designed to make use of this energy, converting it into useful heat as it lessens chimney creo- sote build-up and air pollution. The catalytic combustor consists of a durable temperature resistant ceramic com- position, which is extruded into a cellular, or honeycomb, configuration. After extrusion, this ceramic monolith is fired and then covered with a noble-metal catalyst. When wood smoke contacts this catalyst, chemical changes occur that causes the smoke to ignite at temperatures around 600° F. Normally, smoke will ignite and burn only at temperatures around 1000° F.

CATALYTIC BYPASS DAMPER CONTROL

The operating handle of your Bypass Damper Control is located on the front of the Stove Flue Collar. By moving the Bypass Damper Control the operator can route the exhaust either through the Catalytic Combustor (pushed in) or directly up the flue (pulled out). When starting a fire or refueling, the bypass damper control handle should be pulled out. Once the fire is established it should be pushed in.

Secondary Air Tube

Bypass Damper Control

Tunnel Baffle

Positioning

Stops

Damper

Door

Catalytic

Combustor

Catalyic Combustor

Retainer Clip

PRIMARY AIR CONTROL

The primary combustion air delivery is controlled by the Primary Air Control Assembly. The control handle is lo- cated on the lower right side (front) of the stove - see illustration below. The heat output can be controlled by sliding the handle to a higher or lower heat output set- ting. The fuel, the amount of heat and burn times de- sired, the type of installation are all variables that will affect the control setting. The same control settings in a variety of installations will produce different results. You will need to try different settings so you can learn how much heat to expect and how long the fire will burn.

Primary Air Control Handle

Slide the control to the left for a lower burn

rate, to the right for a higher burn rate.

LOW

 

HIGH

 

 

 

 

 

You will generally want to set the primary air control on low or medium. The stove is safe burning on any setting as long as combustibles are kept at the specified safe distances.

PAGE 14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents EPA Certified Catalytic Wood Burning Stove 775003M, Rev. P, 11/03Important Warnings Table of Contents Selecting a Location Planning Your InstallationSmoke Detectors Canada Requirements Floor ProtectionUSA Requirements Standard Parallel Hearth PAD ShownCombustible Wall Clearances Protected Wall Clearance Alcove ClearancesReduced Masonry Structure Clearance Alcove Outside AIR InstallationAIR Intake Cover Stove Outside Air Floor Duct Floor ProtectorGrounding Stove Acceptable Connector Pipe for INSTALLA- TionsSecuring the Stove to the Floor Remove ASH Drawer ClipChimney Height Requirements Chimney InspectionVapor Barrier At Chimney Penetration 2’ by 10’ Rule for Vent TerminationDraft Test Procedure Draft RequirementsManufactured Mobile Home Standard Using 6 152 mm Diameter Type L-Vent Connector PipeResidential Standard Important NotesWall pass-through with a minimum 9 228.6 mm air space be Sides, to maintain the 9 228.6 mm air space. When fasteningMethod B 228.6 mm Clearance to Combustible Wall Member Inside wall of the Solid-Pak chimney. The inner endCare and OPERATI0N Glass Care and OperationFuel Door HOW to Start and Maintain a Fire BREAK-IN PeriodBypass Damper Control Catalytic Temperature ProbeRefueling Burn Recommended FuelMaintenance FuelDoor / Glass Gasket and ASH Drawer GAS- KET Replacing GlassCatalyst Replacement Side Cut-Away View of FireboxTroubleshooting Catalyst Substrate Cracking Catalyst PluggingCatalyst Deactivation Catalyst SubstrateOverfiring Caused From Improper Operation Overfiring Caused From Improper InstallationOverfiring Damage Specifications Model 1003C Fire Box Size Cubic feetItem no Description Replacement Parts List Model 1003C Damper Assembly Catalytic Combustor System ComponentsBlower Kit BK-100 Outside Air Floor Duct OAFD-SStove-Stat Kit SSK Variable Speed Control, Dial-A-TempSAFETY/LISTING Label EPA Label Service and Maintenance LOG Ownership RecordsWest Taft Avenue Orange, CA
Top Page Image Contents