Sears 139.53535SRT1 Installation Section Pages 12 Installation Step, Proceed to

Page 12

installation Section: Pages 12- 27

installation Step 1

Determine Header Bracket Location

Installation procedures vary according to

garage door types. Follow the instructions which apply to your door.

If the header bracket is not rigidly fastened to

a structural support on the header wall or

ceiling, the safety reverse system may not work properly (see page 30). The door might

not reverse when required, and could cause

serious injury or death.

The garage door springs, cables, pulleys, brackets and their hardware are under extreme

tension. Do not attempt to loosen, move or adjust them yourself. Serious personal injury or death could result. Call for professional

Finished

VerticaI

HeaderGuideline

Walt

Ceiting

garage door service.

2x4

StructuraI

• Close the door and mark the inside

 

vertical centerline of the garage door.

 

• Extend the line onto the header wall

 

above the door.

 

Remember, you can fasten the

 

header bracket within 2 feet of the

 

left or right of the door center only if

 

a torsion spring or center bearing

 

plate is in the way; or you can attach

 

it to the ceiling (refer to page 14)

 

when clearance is minimal. (it may

 

be mounted on the wall upside down

 

if necessary, to gain approximately

 

1/2".)

 

If you need to install the header bracket

 

on a 2x4 (on wall or ceiling), use lag

 

screws (not supplied) to securely fasten

 

the 2x4 to structural supports as shown

 

here and on page 13.

Open your door to the highest point of travel as shown. Draw an intersecting horizontal line on the header wall 2" above the high point. This height will provide travel clearance for the top edge of the door.

Door clearance brackets are available for sectional doors when headroom clearance is less than 2". See accessory page 38.

 

Ceiling

 

 

Header

 

 

Wall

 

Header

,,

2"

Track

 

 

 

_Wall

Track

Highest

Point

 

 

of TraveI

 

Door

 

_

Hig_eCtaPe_int

 

 

Sectional

door

One-piece

door

with curved

track

with horizontal

track

Proceed to Step 2, page 14.

12

Image 12
Contents Owners UAL Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.AStart by Reviewing these Important Safety Alert Symbols Installation section pages 11 InstallationsafetyAdjustment section pages 28 MechanicalElectricalYoull Need Tools Cosed Position Center of the door. See pages 12To your installation One=Piece Door with TrackApply Carton inventory Assembly Installation HardwareSafety Reversing Sensor Installation SeparateAssembly Section Pages 8 Assemble the T=rail Attach the Cable Pulley BracketAssembly Step Install the Trolley on the T-railFasten the T-rail to the Opener Hardware ShownInstall the Chain/Cable Attach the Sprocket Cover To make sure the chain is notTo reduce the risk of severe injury or death to persons Tighten the Chain & CableInstallation Section Pages 12 Installation Step Determine Header Bracket LocationProceed to , Example Fasten the Header Bracket to the CeilingAttach the T=rai! to the Header Bracket If the top panel hits the trolley when you raise Position the OpenerHang the Opener Underside of the railInstall the Premium Control Console Hardware Shown Actual SizeInstall the lights Install the lensesInstafl the Lights and the Lenses Attach the EmergencyElectrical Requirements PermanentConnections Safety Reversing System Safety reversing sensor must be connectedInstall the Safety Reversing Sensor Actual SizeTrouble Shooting OpenerFasten Door Bracket Finished Ceiling Connect Door Arm to Trolley 1i CevisPin5c,g DcoUAr Figure Hole Alignment AlternativeAdjustment Procedures for One-Piece Doors Adjustment Section Pages 28 Adjustment Step Adjust the UP and Down LimitsHow and When to Adjust the Limits Adjust the Force To Adjust the ForcesHow and When Test The Safety Reversing Sensor Test the Safety Reverse SystemImportant safety check IMPORTANT Safety iNSTRUCTiONS To reduce the risk of severe MaintenanceInjury or death to persons ScheduleOperation of the Door Controls seeTo open the door Manual disconnectReceiver and Remote Control Programming 53000SRT Series Garage Door OpenersWith SRT Button With SRT ButtonHaving a Problem? Situation Probable Cause and SolutionSituation Probable Cause Solution OpenerGarage door springs are broken. See above Chain droopsRepair Parts Rail AssemblyPartsInstallation Parts 1418Opener Assembly PaNs Multi-Function Keyless Entry 53885For Sectional Doors Only Index Chain TensionManual Emergency Release Rope & Handle TerminalsCraftsman

139.53535SRT1 specifications

The Sears 139.53535SRT1 is an innovative garage door opener that stands out in the realm of home automation due to its robust features and advanced technologies. This model offers a blend of convenience, security, and performance, making it a popular choice for homeowners seeking efficiency and reliability.

One of the standout features of the 139.53535SRT1 is its powerful motor, designed to lift heavy garage doors with ease. With a lifting capacity suitable for both standard and heavy-duty doors, it operates smoothly and quietly, ensuring minimal disruption in residential areas. The opener also includes safety features such as the automatic reverse function, which prevents accidents by reversing the door's direction if it detects an obstruction.

This model is equipped with the latest technology to enhance user experience and security. The security+ 2.0 technology generates a new code every time the remote is used. This feature provides an additional layer of protection against unauthorized access, ensuring homeowners feel safe and secure when using their garage door opener.

In terms of connectivity, the Sears 139.53535SRT1 comes with built-in Wi-Fi capability. This allows users to control the garage door remotely via a smartphone app. Through the app, users can check the status of their garage door, open or close it from anywhere, and receive notifications about its usage. This feature is particularly beneficial for those who may forget to close the door or need to grant access to someone while away from home.

Additionally, the model includes a convenient battery backup system. This ensures that the garage door opener operates even during power outages, providing peace of mind during inclement weather or disruptions in local power supply.

Installation of the 139.53535SRT1 is user-friendly, thanks to its comprehensive guide and compatibility with most standard garage door setups. Its sleek design also adds a modern touch to any garage space, blending functionality with aesthetics.

In summary, the Sears 139.53535SRT1 garage door opener encompasses a host of innovative features like a powerful motor, advanced security technology, Wi-Fi connectivity, and battery backup. These characteristics make it a top choice for homeowners aiming for both convenience and safety in their garage door solutions.