Sears 139.53535SRT1 Having a Problem?, Situation Probable Cause and Solution

Page 34

Having a Problem?

Situation

Probable Cause and Solution

The opener doesn't operate from either

the Door Control or the remote control:

1.Does the opener have electric power? Plug a lamp into the outlet. If it doesn'tlight, check the fuse box or the circuit breaker. (Some outlets are controlled by a door switch.)

2.Have you disabled all door locks? Review installation instruction warnings on Page 11.

3.Is there a build-up of ice or snow under the door? The door may be frozen to the ground. Remove any restriction.

4.The garage door spring may be broken. Have it replaced.

5.Repeated operation may have tripped the overload protector in the motor. Wait 15 minutes. Try again.

Opener operates from the remote control, but not from the Door Control:

The door operates from the Door

Control, but not from the remote control:

The remote control has short range:

1.Is the Door Control lit? If not, remove the bell wire from the opener terminal screws. Short the red and white terminals by touching both terminals at the same time with a piece of wire. If the opener runs, check for a faulty wire connection at the Door Control, a short under the staples, or a broken wire.

2.Are the wiring connections correct? Review Step 6, page 18.

1.If your model has the Lock feature, make sure the lock is Off.

2.Is any door push button flashing? Your opener needs to re-learn a remote control code. Refer to Instructions on the opener panel.

3.Program the receiver to match the remote control code.

4.Repeat the receiver programming procedure with all remote controls.

1.Change the location of the remote control in your car.

2.Check to be sure the antenna on the side or back panel of opener extends fully downward.

3.Some installations may have shorter range due to a metal door, foil backed insulation, or metal garage siding.

Opener noise is disturbing in living quarters of home:

The garage door opens and closes by itself:

The door doesn't open completely:

If operational noise is a problem because of proximity of the opener to the living quarters, the Vibration Isolator Kit 41A3263 can be installed. This kit was designed to minimize vibration to the house and is easy to install.

1.Be sure that all remote control push buttons are off.

2.Remove the bell wire from the Door Control terminals and operate from the remote control only. If this solves the problem, the Door Control is faulty (replace), or there is an intermittent short on the wire between the Door Control and the opener.

1.If the door has been working properly but now doesn't open all the way, increase the up force. See page 29.

2.Is something obstructing the door? Remove the obstruction or repair the door.

3.If door opens at least 5 feet, the travel limits may need to be increased. One turn equals 2 inches of travel. See page 28.

Repeat the safety reverse test after the adjustment is complete.

The door stops but doesn't close

completely:

Review the travel limits adjustment procedures on page 28.

Repeat the safety reverse test after any adjustment of door arm length, close force or down limit.

34

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Owners UAL Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.AAdjustment section pages 28 Start by Reviewing these Important Safety Alert SymbolsInstallation section pages 11 Installationsafety MechanicalElectricalYoull Need Tools Cosed Position Center of the door. See pages 12One=Piece Door with Track To your installationApply Carton inventory Safety Reversing Sensor Installation AssemblyInstallation Hardware SeparateAssembly Section Pages 8 Assemble the T=rail Attach the Cable Pulley BracketFasten the T-rail to the Opener Assembly StepInstall the Trolley on the T-rail Hardware ShownInstall the Chain/Cable Attach the Sprocket Cover To make sure the chain is notTo reduce the risk of severe injury or death to persons Tighten the Chain & CableDetermine Header Bracket Location Installation Section Pages 12 Installation StepProceed to , Example Fasten the Header Bracket to the CeilingAttach the T=rai! to the Header Bracket If the top panel hits the trolley when you raise Position the OpenerHang the Opener Underside of the railInstall the Premium Control Console Hardware Shown Actual SizeInstafl the Lights and the Lenses Install the lightsInstall the lenses Attach the EmergencyPermanent Electrical RequirementsConnections Safety Reversing System Safety reversing sensor must be connectedInstall the Safety Reversing Sensor Actual SizeTrouble Shooting OpenerFasten Door Bracket Finished Ceiling 5c,g DcoUAr Figure Connect Door Arm to Trolley1i CevisPin Hole Alignment AlternativeAdjustment Procedures for One-Piece Doors Adjust the UP and Down Limits Adjustment Section Pages 28 Adjustment StepHow and When to Adjust the Limits To Adjust the Forces Adjust the ForceHow and When Test the Safety Reverse System Test The Safety Reversing SensorImportant safety check Injury or death to persons IMPORTANT Safety iNSTRUCTiONS To reduce the risk of severeMaintenance ScheduleTo open the door Operation of the DoorControls see Manual disconnectWith SRT Button Receiver and Remote Control Programming53000SRT Series Garage Door Openers With SRT ButtonHaving a Problem? Situation Probable Cause and SolutionGarage door springs are broken. See above Situation Probable Cause SolutionOpener Chain droopsInstallation Parts Repair PartsRail AssemblyParts 1418Opener Assembly PaNs 53885 Multi-Function Keyless EntryFor Sectional Doors Only Manual Emergency Release Rope & Handle IndexChain Tension TerminalsCraftsman

139.53535SRT1 specifications

The Sears 139.53535SRT1 is an innovative garage door opener that stands out in the realm of home automation due to its robust features and advanced technologies. This model offers a blend of convenience, security, and performance, making it a popular choice for homeowners seeking efficiency and reliability.

One of the standout features of the 139.53535SRT1 is its powerful motor, designed to lift heavy garage doors with ease. With a lifting capacity suitable for both standard and heavy-duty doors, it operates smoothly and quietly, ensuring minimal disruption in residential areas. The opener also includes safety features such as the automatic reverse function, which prevents accidents by reversing the door's direction if it detects an obstruction.

This model is equipped with the latest technology to enhance user experience and security. The security+ 2.0 technology generates a new code every time the remote is used. This feature provides an additional layer of protection against unauthorized access, ensuring homeowners feel safe and secure when using their garage door opener.

In terms of connectivity, the Sears 139.53535SRT1 comes with built-in Wi-Fi capability. This allows users to control the garage door remotely via a smartphone app. Through the app, users can check the status of their garage door, open or close it from anywhere, and receive notifications about its usage. This feature is particularly beneficial for those who may forget to close the door or need to grant access to someone while away from home.

Additionally, the model includes a convenient battery backup system. This ensures that the garage door opener operates even during power outages, providing peace of mind during inclement weather or disruptions in local power supply.

Installation of the 139.53535SRT1 is user-friendly, thanks to its comprehensive guide and compatibility with most standard garage door setups. Its sleek design also adds a modern touch to any garage space, blending functionality with aesthetics.

In summary, the Sears 139.53535SRT1 garage door opener encompasses a host of innovative features like a powerful motor, advanced security technology, Wi-Fi connectivity, and battery backup. These characteristics make it a top choice for homeowners aiming for both convenience and safety in their garage door solutions.
Top Page Image Contents