Sears 139.53535SRT1 Safety Reversing System, Safety reversing sensor must be connected

Page 21

The Safety Reversing System

Information you'll need before you begin the installation of the safety reversing sensor.

The safety reversing sensor must be connected

and aligned correctly before the garage door opener will move in the down direction. This is a required safety device and cannot be disabled.

Installation procedures are the same for sectional and one-piece doors.

Without a properly working safety reversing

sensor, persons (particularly children) could be injured or killed by a closing garage door. Read and follow all instructions.

To protect small children, install the safety reversing sensor so that the beam will be no higher than 4"-6" above the garage floor.

Disconnect power to the garage door opener before installing the safety reversing sensor.

Be sure power to the opener is disconnected.

The sending eye transmits an invisible light beam to the receiving eye. The units can be installed on either side of the garage door as long as the sun never shines directly into the receiving eye lens. Look at the label on the connector end of each case to identify the sensors.

The brackets must be connected and fastened so that the sending and receiving eyes face each other as shown in Figure 1.

If an obstruction breaks the light beam while the garage door is closing, the door will stop and reverse to full open position and the opener lights will flash for 5 seconds.

The brackets must be securely fastened to a solid surface such as the studs on either side of the door, or add a piece of wood at each location if installing in masonry construction,

The invisible light beam path must be unobstructed, No part of the garage door (or door tracks, springs, hinges, rollers or other hardware) can interrupt the beam while the door is closing, If it does, use a piece of wood to build out each sensor mounting location to the minimum depth required for light beam clearance,

Sensor

Beam

Sensor

Beam

4-6"

max

4-6" max

above

floor

above

floor

/

InvisibIe Light Beam

Protection Area

Figure 1 : Facing the door from inside the garage

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A Owners UALInstallation section pages 11 Installationsafety Start by Reviewing these Important Safety Alert SymbolsAdjustment section pages 28 MechanicalElectricalYoull Need Tools Center of the door. See pages 12 Cosed PositionTo your installation One=Piece Door with TrackApply Carton inventory Installation Hardware AssemblySafety Reversing Sensor Installation SeparateAssemble the T=rail Attach the Cable Pulley Bracket Assembly Section Pages 8Install the Trolley on the T-rail Assembly StepFasten the T-rail to the Opener Hardware ShownTo make sure the chain is not Install the Chain/Cable Attach the Sprocket CoverTighten the Chain & Cable To reduce the risk of severe injury or death to personsInstallation Section Pages 12 Installation Step Determine Header Bracket LocationProceed to , Example Bracket to the Ceiling Fasten the HeaderAttach the T=rai! to the Header Bracket Position the Opener If the top panel hits the trolley when you raiseUnderside of the rail Hang the OpenerHardware Shown Actual Size Install the Premium Control ConsoleInstall the lenses Install the lightsInstafl the Lights and the Lenses Attach the EmergencyElectrical Requirements PermanentConnections Safety reversing sensor must be connected Safety Reversing SystemActual Size Install the Safety Reversing SensorOpener Trouble ShootingFasten Door Bracket Finished Ceiling 1i CevisPin Connect Door Arm to Trolley5c,g DcoUAr Figure Hole Alignment AlternativeAdjustment Procedures for One-Piece Doors Adjustment Section Pages 28 Adjustment Step Adjust the UP and Down LimitsHow and When to Adjust the Limits Adjust the Force To Adjust the ForcesHow and When Test The Safety Reversing Sensor Test the Safety Reverse SystemImportant safety check Maintenance IMPORTANT Safety iNSTRUCTiONS To reduce the risk of severeInjury or death to persons ScheduleControls see Operation of the DoorTo open the door Manual disconnect53000SRT Series Garage Door Openers Receiver and Remote Control ProgrammingWith SRT Button With SRT ButtonSituation Probable Cause and Solution Having a Problem?Opener Situation Probable Cause SolutionGarage door springs are broken. See above Chain droopsRail AssemblyParts Repair PartsInstallation Parts 1418Opener Assembly PaNs Multi-Function Keyless Entry 53885For Sectional Doors Only Chain Tension IndexManual Emergency Release Rope & Handle TerminalsCraftsman

139.53535SRT1 specifications

The Sears 139.53535SRT1 is an innovative garage door opener that stands out in the realm of home automation due to its robust features and advanced technologies. This model offers a blend of convenience, security, and performance, making it a popular choice for homeowners seeking efficiency and reliability.

One of the standout features of the 139.53535SRT1 is its powerful motor, designed to lift heavy garage doors with ease. With a lifting capacity suitable for both standard and heavy-duty doors, it operates smoothly and quietly, ensuring minimal disruption in residential areas. The opener also includes safety features such as the automatic reverse function, which prevents accidents by reversing the door's direction if it detects an obstruction.

This model is equipped with the latest technology to enhance user experience and security. The security+ 2.0 technology generates a new code every time the remote is used. This feature provides an additional layer of protection against unauthorized access, ensuring homeowners feel safe and secure when using their garage door opener.

In terms of connectivity, the Sears 139.53535SRT1 comes with built-in Wi-Fi capability. This allows users to control the garage door remotely via a smartphone app. Through the app, users can check the status of their garage door, open or close it from anywhere, and receive notifications about its usage. This feature is particularly beneficial for those who may forget to close the door or need to grant access to someone while away from home.

Additionally, the model includes a convenient battery backup system. This ensures that the garage door opener operates even during power outages, providing peace of mind during inclement weather or disruptions in local power supply.

Installation of the 139.53535SRT1 is user-friendly, thanks to its comprehensive guide and compatibility with most standard garage door setups. Its sleek design also adds a modern touch to any garage space, blending functionality with aesthetics.

In summary, the Sears 139.53535SRT1 garage door opener encompasses a host of innovative features like a powerful motor, advanced security technology, Wi-Fi connectivity, and battery backup. These characteristics make it a top choice for homeowners aiming for both convenience and safety in their garage door solutions.
Top Page Image Contents