Sears 139.53535SRT1 Install the Premium Control Console, Hardware Shown Actual Size

Page 18

installation Step 6

Install the Premium Control Console

Locate the door control within sight of the door at a minimum height of 5 feet where small children cannot reach, and away from all moving parts of the door and door hardware.

The door control is typically attached directly to the wall. If installing into drywall, drill 5/32" holes and use the anchors _rovided. Forpre-wired installations (as in new home construction), Console models may be mounted to a standard single gang box (Figure 2).

1.Strip 1/4" of insulation from one end of the bell wire and connect it to the two screw terminals on

the back of the door control: white to 2, and white/red to 1.

2.Pry off cover along one side with a screwdriver blade (see Figure 1). Fasten with 6ABx1-1/4" self- tapping screws (standard installation) or 6-32x1" machine screws (pre-wired installation) as follows:

•Install bottom screw, allowing 1/8" to protrude above wall surface.

•Position bottom of door control on screw head and slide down to secure. Adjust screw for snug fit.

•Drill and install top screw with care to avoid cracking plastic housing. Do not overtighten.

•Insert top tabs and snap on cover.

3.(For standard installation) Run the bell wire up the wall and across the ceiling to the opener. Use insulated staples to secure the wire in several places. Be careful not to pierce the wire with a staple, creating a short.

4.Connect the bell wire to the terminal screws on the opener panel: white to 2; white/red to 1.

5.Position the antenna wire as shown.

 

2-Conductor

Opener

 

BeII Wire

Terminal Screws

 

 

Top

Lighted

Mounting

Push

Button

Hole

 

/

_TerminaI

 

Screws

 

 

 

 

iRED

 

 

Bottom

 

 

Mounting

 

 

Hole

 

Light

VIEW

 

BACK

 

Lock

 

PREMIUM CONTROL

CONSOLE

 

Do not connect to live electrical wiring. Connect only to 24 Volt low voltage wires. Connection to live wires or higher voltage may cause serious injury from shock, burn or electrocution.

Children operating or playing with a garage door opener can injure themselves or others.

The garage door could close and cause serious injury or death.

install the door control (or any additional push buttons) out of the reach of children and away from all moving parts of the door and door hardware, but where the garage door is visible.

Do not allow children to operate the push button(s) or the remote control(s).

A moving garage door could injure someone under it. Activate the opener only when the

door is properly adjusted, you can see it clearly, and there are no obstructions to door travel.

Hardware Shown Actual Size

 

 

 

Insulated

Control

Console (std installation)

Staples

 

Control Console

(pre-wired)

Dry Walt Anchors

Figure

1

 

Figure 2

REMOVE & REPLACE

COVER

PRE-WIRED

To Replace,

 

To Remove,

INSTALLATION

 

 

insert

 

Twist

 

Tabs

 

Here

 

24 Vott

2-Conductor Bell Wire

O

[]

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Owners UAL Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.AAdjustment section pages 28 Start by Reviewing these Important Safety Alert SymbolsInstallation section pages 11 Installationsafety MechanicalElectricalYoull Need Tools Cosed Position Center of the door. See pages 12To your installation One=Piece Door with TrackApply Carton inventory Safety Reversing Sensor Installation AssemblyInstallation Hardware SeparateAssembly Section Pages 8 Assemble the T=rail Attach the Cable Pulley BracketFasten the T-rail to the Opener Assembly StepInstall the Trolley on the T-rail Hardware ShownInstall the Chain/Cable Attach the Sprocket Cover To make sure the chain is notTo reduce the risk of severe injury or death to persons Tighten the Chain & CableInstallation Section Pages 12 Installation Step Determine Header Bracket LocationProceed to , Example Fasten the Header Bracket to the CeilingAttach the T=rai! to the Header Bracket If the top panel hits the trolley when you raise Position the OpenerHang the Opener Underside of the railInstall the Premium Control Console Hardware Shown Actual SizeInstafl the Lights and the Lenses Install the lightsInstall the lenses Attach the EmergencyElectrical Requirements PermanentConnections Safety Reversing System Safety reversing sensor must be connectedInstall the Safety Reversing Sensor Actual SizeTrouble Shooting OpenerFasten Door Bracket Finished Ceiling 5c,g DcoUAr Figure Connect Door Arm to Trolley1i CevisPin Hole Alignment AlternativeAdjustment Procedures for One-Piece Doors Adjustment Section Pages 28 Adjustment Step Adjust the UP and Down LimitsHow and When to Adjust the Limits Adjust the Force To Adjust the ForcesHow and When Test The Safety Reversing Sensor Test the Safety Reverse SystemImportant safety check Injury or death to persons IMPORTANT Safety iNSTRUCTiONS To reduce the risk of severeMaintenance ScheduleTo open the door Operation of the DoorControls see Manual disconnectWith SRT Button Receiver and Remote Control Programming53000SRT Series Garage Door Openers With SRT ButtonHaving a Problem? Situation Probable Cause and SolutionGarage door springs are broken. See above Situation Probable Cause SolutionOpener Chain droopsInstallation Parts Repair PartsRail AssemblyParts 1418Opener Assembly PaNs Multi-Function Keyless Entry 53885For Sectional Doors Only Manual Emergency Release Rope & Handle IndexChain Tension TerminalsCraftsman

139.53535SRT1 specifications

The Sears 139.53535SRT1 is an innovative garage door opener that stands out in the realm of home automation due to its robust features and advanced technologies. This model offers a blend of convenience, security, and performance, making it a popular choice for homeowners seeking efficiency and reliability.

One of the standout features of the 139.53535SRT1 is its powerful motor, designed to lift heavy garage doors with ease. With a lifting capacity suitable for both standard and heavy-duty doors, it operates smoothly and quietly, ensuring minimal disruption in residential areas. The opener also includes safety features such as the automatic reverse function, which prevents accidents by reversing the door's direction if it detects an obstruction.

This model is equipped with the latest technology to enhance user experience and security. The security+ 2.0 technology generates a new code every time the remote is used. This feature provides an additional layer of protection against unauthorized access, ensuring homeowners feel safe and secure when using their garage door opener.

In terms of connectivity, the Sears 139.53535SRT1 comes with built-in Wi-Fi capability. This allows users to control the garage door remotely via a smartphone app. Through the app, users can check the status of their garage door, open or close it from anywhere, and receive notifications about its usage. This feature is particularly beneficial for those who may forget to close the door or need to grant access to someone while away from home.

Additionally, the model includes a convenient battery backup system. This ensures that the garage door opener operates even during power outages, providing peace of mind during inclement weather or disruptions in local power supply.

Installation of the 139.53535SRT1 is user-friendly, thanks to its comprehensive guide and compatibility with most standard garage door setups. Its sleek design also adds a modern touch to any garage space, blending functionality with aesthetics.

In summary, the Sears 139.53535SRT1 garage door opener encompasses a host of innovative features like a powerful motor, advanced security technology, Wi-Fi connectivity, and battery backup. These characteristics make it a top choice for homeowners aiming for both convenience and safety in their garage door solutions.
Top Page Image Contents