Sears 139.53535SRT1 Operation of the Door, Controls see, To open the door, Manual disconnect

Operation of Your Opener

Activate the opener with any of the following:

•The Remote Control: Hold push button down until the door starts to move.

•The Door Control: Hold push button down until the door starts to move.

•The Outdoor Key Switch or Keyless Entry: (See Accessories)

When the opener is activated with the safety reversing sensor installed and correctly aligned:

1.

If open, the

door will close.

If closed,

the

door

will

open.

2.

If closing,

the door

will

reverse.

3.

If opening,

the door will

stop

(allowing

space

for

entry

and exit of pets and for fresh air).

4.

If the

door has been stopped

in a partially open

position,

it will close.

5.

If obstructed

while

closing,

the

door will

reverse.

6.

If obstructed

while

opening,

the

door

will

stop.

7.

The garage

door will reverse

in the closing cycle

when the invisible beam is broken. If fully open,

the door will not close when the beam is broken.

Weak or broken springs could allow an open door to fall (either rapidly or unexpectedly), resulting in serious injury, death or property

damage, if possible, use the emergency release rope and handle only when the door is fully closed.

		To open the door
		manually:
		The door should be
	!ease Arm	fully closed if possible.
		Pull down on the red
		emergency	release
		handle and lift the door
Trolley		manually.	To
Emergency		reconnect	the door		to
		the opener,		press	the
Release	Handte
(Pult	Down)	Door Control		push
Manual disconnect		button.

position

The sensor has no effect in the opening cycle.

If the sensor is not installed, or is not aligned

correctly, the door won't close from any remote transmitter. You can close the door with the Door

Control, the Outdoor Key Switch, or Keyless Entry, however, if you activate them until down travel is

complete, tf you release them too soon, the door will reverse.

The opener lights will blink for 5 seconds when the safety reversing sensor causes the door to reverse.

Opener Lights will turn on under the following conditions: When the opener is initially plugged in; when the power is interrupted; when the opener is activated. They will turn off automatically after 4-1/2

minutes or provide constant light when the Light feature is activated. Bulb size is 75 watts maximum.

The lockout feature

prevents the trolley from reconnecting automatically. Pull the emergency handle down and back (toward the

opener). The door can then be raised and lowered

manually as often as necessary. To disengage the Lockout Feature, pull the emergency handle straight down. The trolley will reconnect on the next

UP or Down operation.

Trolley

Release Arm

Trolley

Emergency

ReIease Handte

(PulI Down & Back

Towards Opener)

Lockout position

Operation of the Door

Press the lighted push button to open or close the door.

Press again to reverse the door during the closing cycle or to stop the door while it'sopening. Premium Console:

Light Feature - Press the large round Light button. If the opener lights are off, they will turn on. If the opener lights are on, (even in the 4-1/2 minute automatic cycle) they will turn off.

But if you use the Light button to turn the lights on and then activate the opener, the lights will turn off after 4-1/2 minutes.

The Light button will not control the opener lights when the door is in motion.

Controls (see page 18)

Premium Console (cont.):

Lock Feature - The Lock feature is designed to prevent operation of the door from remote controls. However, the door will open and close from the Door Control, the Outdoor Key Switch and the Keyless Entry Accessories.

To Activate: Press and hold the small round Lock button for 2 seconds. The push button light will flash as long as the Lock feature is on.

To turn off: Press and hold the Lock button again for 2 seconds.The push button light will stop flashing. The Lock feature will also turn off whenever the "SRT" button on the opener panel is activated.

32