State Industries GP 6 40YPC T 100, GP 6 50YPC T 100 Vent Pipe System, Draft Hood Installation

Page 13

Confined Space

Alternative

Air Inlet

1 sq. in. per

4000 BTUH

Gable Vent to Outdoors

Install Above Insulation

Outlet Air

to the Attic 1 sq. in. per 4000 BTUH

Inlet Air from the Crawl Space

Open

Foundation

Vent

Alternative

Opening

Location

Confined

Space

1 sq. in. per

3000 BTUH

All Air From Outdoors - Using A Single Permanent Opening

FIGURE 8B.

Vent Pipe System

All Air From Outdoors: Inlet Air From Ventilated

Crawl Space/Outlet Air To Ventilated Attic

This water heater uses a non-direct, single-pipe vent system to remove exhaust gases created by the burning of fossil fuels. Air for combustion is taken from the immediate

Confined Space

FIGURE 6.

Gable Vent to Outdoors

Install Above

Outlet Air to the Attic 1 sq. in. per 4000 BTUH

Inlet Air Duct 1 sq. in. per 4000 BTUH

water heater location or is ducted in from the outside (see “Combustion Air Supply and Ventilation”).

This water heater must be properly vented for the removal of exhaust gases to the outside atmosphere. Correct installation of the vent pipe system is mandatory for the proper and efficient operation of this water heater and is an important factor in the life of the unit.

The vent pipe must be installed according to all local and state codes or, in the absence of local and state codes, the “National Fuel Gas Code”, ANSI Z223.1(NFPA 54)-current edition. The vent pipe installation must not be obstructed so as to prevent the removal of exhaust gases to the outside atmosphere.

IMPORTANT: The use of vent dampers is not

12” Max.

All Air from Outdoors Through Ventilated Attic

FIGURE 7.

recommended by the manufacturer of this water heater. Although some vent dampers are certified by CSA International, this certification applies to the vent damper device only and does not mean they are certified for use on this water heater.

Confined Space

1 sq. in. per

2000 BTUH

Outlet

Outdoor

Air Ducts

U.L. recognized fuel gas and carbon monoxide (CO) detectors are recommended in all applications and should be installed using the manufacturer’s instructions and local codes, rules, or regulations.

IMPORTANT: If you lack the necessary skills required to properly install this venting system, you should not proceed, but get help from a qualified technician.

Draft Hood Installation

Inlet

1 sq. in. per

2000 BTUH

All Air From Outdoors Using Horizontal Ducts

FIGURE 8A.

 

Sheet Metal Screws (Four Provided)

 

Legs

Draft Hood

 

 

 

 

Legs

Slot

 

Slot

 

 

Jacket Top

Install The Draft Hood With The Four Screws Provided.

FIGURE 9

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Residential GAS Water Heaters Table of Contents Safety Precautions Safe INSTALLATION, USE and ServiceFire or Explosion Hazard GET to Know Your Water Heater GAS Models Typical InstallationUnpacking the Water Heater Excessive Weight Hazard Installing Your GAS Water HeaterImportant Information About This Water Heater Consumer InformationSite Location Location RequirementsCarbon Monoxide Poisoning Hazard State of California Clearances and AccessibilityGAS Supply Gas Pressure TestingGas Requirements Gas PipingGas Pipe Capacity Table Unconfined Space Combustion AIR & VentilationConfined Space Minimum Btuh InputAll Air from Outdoors All Air from Inside the BuildingLouvers and Grilles Vent Pipe System Draft Hood InstallationVent Pipe Size Vent ConnectorsChimney Connection Vertical Exhaust Gas VentWater System Piping Piping InstallationClosed System/Thermal Expansion Temperature and Pressure Relief ValveRelief Valve and Pipe Insulation Temperature & Pressure Relief ValveCombination Space Heating/Potable Water System Discharge LineWiring Diagram Solar InstallationElectrical Connections Important Information about this Water Heater Installation ChecklistOperating Instructions Operating Your Water HeaterChecking the Draft Water Heater OperationBurn Hazard Burner Flames Water Temperature RegulationEmergency Shut Down Operational Conditions Safety Shut-offCondensation Water Heater SoundsPowered Anode Operation Routine Preventive MaintenanceDraining and Flushing Replacement Parts Maintenance of Your Water HeaterRemoving the Manifold/Burner Assembly Removing the Burner from the Manifold/ Burner AssemblyCleaning the Combustion Chamber and Air Diverter Assembly Replacing the Flame Sense/Hot Surface igniter AssemblyReplacing the Manifold/Burner Assembly Removing the Gas Control Valve/Thermostat Removing and Replacing the Gas Control Valve/ThermostatReplacing the Gas Valve Troubleshooting Chart Pressurized Combustion Chamber System Operational ChecklistCont Control Display Status Problem Solution Control Display TroubleshootingControl Display Status Problem Solution FV-SENSE and Open Flashing YES Troubleshooting FlowchartRepair Parts Illustration Repair Parts ListListed Parts Kits and Illustrations Page Page Page Year Limited Residential GAS WarrantyImportant Information

317998-002, GP 6 50YPC T 100, GP 6 40YPC T 100 specifications

State Industries has long been at the forefront of technological advancements and innovative design in the industrial market. The company has developed a range of high-efficiency products designed for various applications, including the GP 6 40YPC T 100 and GP 6 50YPC T 100 models, as well as the 317998-002 component. Each product in this lineup is characterized by specific features and cutting-edge technologies tailored to meet diverse operational needs.

The GP 6 40YPC T 100 model boasts a robust construction aimed at durability and resilience in demanding environments. Its design incorporates advanced materials that resist wear and corrosion, ensuring a prolonged lifespan and reduced maintenance requirements. The model operates efficiently even in high-pressure scenarios, making it suitable for various industrial applications, including manufacturing and processing.

In contrast, the GP 6 50YPC T 100 model is designed with a focus on maximizing performance and energy efficiency. It features an optimized airflow system that enhances heat dissipation, preventing overheating and maintaining operational integrity. This model is ideal for applications that require continuous operation, as it minimizes downtime and maximizes productivity. Additionally, the GP 6 50YPC T 100 is equipped with smart technology that monitors performance metrics, providing real-time feedback on operational efficiency.

The 317998-002 component serves as a critical element in both models, acting as a versatile interface that integrates seamlessly with existing systems. It is designed to enhance connectivity and facilitate communication between various industrial components, promoting improved efficiency and ease of integration.

Both the GP 6 models and the 317998-002 feature user-friendly interfaces, allowing operators to easily manage and adjust settings. This focus on user experience helps to reduce training time and improve overall operational efficiency. Furthermore, both models adhere to strict industry standards, ensuring reliability and safety in all conditions.

In summary, State Industries' GP 6 40YPC T 100 and GP 6 50YPC T 100 models, along with the 317998-002 component, represent the pinnacle of innovation and reliability in industrial solutions. Their advanced features, technologies, and characteristics make them suitable choices for organizations looking to enhance productivity and operational efficiency in a variety of applications. With a commitment to quality and performance, State Industries continues to set the standard for excellence in the industry.
Top Page Image Contents