Harman Stove Company P43 owner manual #1 Preferred method, #2 Preferred method

Page 10

Venting

3 ft.

to combustibles

Fig. 8

 

 

 

 

3 ft.

 

to combustibles

#1 Preferred method

This method provides excellent venting for normal operation and allows the stove to be in- stalled closest to the wall. Two inches from the wall is safe; however, four inches allows better access to remove the rear panel. The vertical portion of the vent should be three to five feet high. This vertical section will help provide natural draft in the event of a power failure. Note: Do not place joints within wall pass-throughs.

3 ft.

to combustibles

 

 

 

 

Fig. 9

 

3 ft.

to combustibles

#2 Preferred method

This method also provides excellent venting for normal operation but requires the stove to be installed farther from the wall. The vertical portion of the vent should be three to five feet high and at least three inches from a combustible wall. This vertical section will provide natural draft in the event of a power failure.

If the stove is installed below grade be sure the vent termination is at least 18" above grade. The outlet must also be 1 foot from the house/building.

Note: Do not place joints within wall pass- throughs.

CAUTION

Keep combustible materials (such as grass, leaves, etc.) at least 3 feet away from the flue outlet on the outside of the building.

12" min. wall to outlet

10P43 Pellet Stove

36" min clearance to any combustible material

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Installation & Operating Manual Safety NoticeWHI Table of Contents IntroductionImportant Notes Removing rear cover panels Assembly and InstallationUnpacking FirebrickInstallation InstallingVenting With outside air installed, 6 feetAddition, the following must be observed Venting Vent PipeDirect Vent Wall Passthrough Kit Outside Air#1 Preferred method #2 Preferred method#5 Installing into an existing #4 Installing into an existing chimneyFireplace chimney #6 Installing into an existing fireplace chimney #7 Installing into an existing chimneyMinimum flue vent configuration #8 Installing through the ceilingStatus light error messages P43 Automatic Ignition ESP ControlRoom Temperature Mode P43 Automatic IGNITION/OPERATIONFeed Adjuster Knob Stove Temperature ModeShut Down Procedure P43 Automatic Start UP Flame Guide SeeHint #7Manual Stove Temperature Mode P43 Manual IGNITION/OperationIgniter Switch toMANUAL down position P43 Manual Start UPP43 Low Draft Voltage Adjustment Low Draft Voltage AdjustmentRoom Sensor Installation Room Sensor and Rear Shield InstallationRear Shields Cleaning MaintenanceCleaning the Door Glass Removing AshesSoot and Fly Ash P43 Maintenance Burn Pot Burn Pot Cleaning and MaintenanceP43 Maintenance Cleaning the Feeder Body Pellet Fines will build up in this areaP43 Trouble-Shooting Cleaning Burn PotP43 Feeder 12.375 P43 Specifications28.5 Options P43 Wiring Diagram P43 Parts List Description Part NumberHarman Gold Warranty

P43 specifications

The Harman Stove Company P43 is a sophisticated pellet stove renowned for its efficiency, versatility, and modern design. Tailored for homeowners who seek both functionality and aesthetic appeal, the P43 offers a compelling option for heating spaces while contributing to an environmentally friendly lifestyle.

At the heart of the P43 is its impressive heating capacity. It can warm areas up to 1,200 square feet, making it suitable for a variety of home sizes. Its heat output ranges from a low of 8,200 BTUs to a maximum of 43,000 BTUs, allowing users to customize heating levels according to their needs. This adaptability is further enhanced by the unit's easy-to-use control settings that enable precise adjustments for different heating requirements and comfort levels.

One standout feature of the P43 is its efficient heat exchanger system. This technology promotes optimal combustion, ensuring that the maximum amount of heat is produced while minimizing waste. As a result, not only does this contribute to cost-effective heating, but it also enhances the stove's environmental performance by reducing emissions. The P43 is certified by the EPA, confirming its compliance with stringent environmental standards.

The P43 also integrates advanced automation technologies, such as Touch Control Technology, which simplifies the operation of the stove. Users can easily manage settings through a digital interface, allowing for setting timers, adjusting burn rates, and monitoring fuel levels. This level of automation makes it particularly appealing for tech-savvy homeowners who appreciate convenience in their heating solutions.

Another defining characteristic of the P43 is its design. With a sleek, modern look, the pellet stove is available in different finishes, allowing it to seamlessly blend into various home decors. The window remains large and unobstructed, providing a clear view of the fire and enhancing the ambiance of any room.

Additionally, Harman’s renowned build quality ensures that the P43 is not only functional but also durable. Constructed from high-quality materials, the stove is designed to offer long-lasting performance. The unit's efficient fuel feeding system minimizes the need for constant refueling, further enhancing its usability.

Overall, the Harman Stove Company P43 represents a perfect fusion of technology, efficiency, and design. Its strong performance, user-friendly interface, and aesthetic appeal make it a leading choice for those who prioritize comfort and sustainability in their home heating solutions.
Top Page Image Contents