Harman Stove Company All About Harman Direct Vent Wall Passthrough Kit and Solutions for Common Issues
Page 9

Venting

Outside air flex pipe goes here.

Flex pipe part#

1-00-08543 (25')

Inlet Cover part# 1-10-08542

Direct Vent Wall Passthrough Kit

(part #1-00-677077)

Outside Air

Here are four benefits of outside air:

1.Having air introduced from outside the living area boosts thermal efficiency. Because the make up air is not being drawn in through leaky windows or doors.

2.Outside air connection eliminates draft problems that can occur in tight homes.

3.Outside air connection reduces smoke spillage in the event of a power failure.

4.Outside air connection allows your vent termination to be as close as 18" from windows or doors.

Outside air is optional, except in mobile homes and where building codes require. The benefit of outside air is mainly noticed in small, very tight, houses.

To install outside air use 2 3/8" I.D. non-combus- tible flex pipe. There is a break-away hole on the rear panel of the P43 stove which must be removed before connecting the flex pipe. The pipe should be run outside and terminate to the side or below the vent pipe outlet so the flue outlet is more than 12" from the inlet cover. The maximum length run of this pipe is 15 feet. If a longer run is needed the size must be increased to 3". Inlet cover, part number 1-10-08542 should be used to keep birds, rodents, etc.out of the pipe.

You may choose to use the optional Direct Vent Wall Passthrough Kit (part #1-00-677077) which incorporates the venting passthrough and outside air inlet into one component.

HRV

When installing in a house with a Heat Reclaim- ing Ventilation System (HRV) be sure the system is balanced and is not creating a negative pressure in the house.

P43 Pellet Stove

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Safety Notice Installation & Operating ManualWHI Introduction Table of ContentsImportant Notes Unpacking Assembly and InstallationRemoving rear cover panels FirebrickInstalling InstallationWith outside air installed, 6 feet VentingAddition, the following must be observed Vent Pipe VentingOutside Air Direct Vent Wall Passthrough Kit#2 Preferred method #1 Preferred method#4 Installing into an existing chimney #5 Installing into an existingFireplace chimney #7 Installing into an existing chimney #6 Installing into an existing fireplace chimney#8 Installing through the ceiling Minimum flue vent configurationP43 Automatic Ignition ESP Control Status light error messagesP43 Automatic IGNITION/OPERATION Room Temperature ModeStove Temperature Mode Feed Adjuster KnobShut Down Procedure Flame Guide SeeHint #7 P43 Automatic Start UPP43 Manual IGNITION/Operation Manual Stove Temperature ModeP43 Manual Start UP Igniter Switch toMANUAL down positionLow Draft Voltage Adjustment P43 Low Draft Voltage AdjustmentRoom Sensor and Rear Shield Installation Room Sensor InstallationRear Shields Cleaning the Door Glass MaintenanceCleaning Removing AshesSoot and Fly Ash Burn Pot Cleaning and Maintenance P43 Maintenance Burn PotPellet Fines will build up in this area P43 Maintenance Cleaning the Feeder BodyCleaning Burn Pot P43 Trouble-ShootingP43 Feeder P43 Specifications 12.37528.5 Options P43 Wiring Diagram Description Part Number P43 Parts ListHarman Gold Warranty

P43 specifications

The Harman Stove Company P43 is a sophisticated pellet stove renowned for its efficiency, versatility, and modern design. Tailored for homeowners who seek both functionality and aesthetic appeal, the P43 offers a compelling option for heating spaces while contributing to an environmentally friendly lifestyle.

At the heart of the P43 is its impressive heating capacity. It can warm areas up to 1,200 square feet, making it suitable for a variety of home sizes. Its heat output ranges from a low of 8,200 BTUs to a maximum of 43,000 BTUs, allowing users to customize heating levels according to their needs. This adaptability is further enhanced by the unit's easy-to-use control settings that enable precise adjustments for different heating requirements and comfort levels.

One standout feature of the P43 is its efficient heat exchanger system. This technology promotes optimal combustion, ensuring that the maximum amount of heat is produced while minimizing waste. As a result, not only does this contribute to cost-effective heating, but it also enhances the stove's environmental performance by reducing emissions. The P43 is certified by the EPA, confirming its compliance with stringent environmental standards.

The P43 also integrates advanced automation technologies, such as Touch Control Technology, which simplifies the operation of the stove. Users can easily manage settings through a digital interface, allowing for setting timers, adjusting burn rates, and monitoring fuel levels. This level of automation makes it particularly appealing for tech-savvy homeowners who appreciate convenience in their heating solutions.

Another defining characteristic of the P43 is its design. With a sleek, modern look, the pellet stove is available in different finishes, allowing it to seamlessly blend into various home decors. The window remains large and unobstructed, providing a clear view of the fire and enhancing the ambiance of any room.

Additionally, Harman’s renowned build quality ensures that the P43 is not only functional but also durable. Constructed from high-quality materials, the stove is designed to offer long-lasting performance. The unit's efficient fuel feeding system minimizes the need for constant refueling, further enhancing its usability.

Overall, the Harman Stove Company P43 represents a perfect fusion of technology, efficiency, and design. Its strong performance, user-friendly interface, and aesthetic appeal make it a leading choice for those who prioritize comfort and sustainability in their home heating solutions.
Top Page Image Contents