Harman Stove Company P43 Assembly and Installation, Unpacking, Removing rear cover panels

Page 5

Assembly and Installation

 

Shipping Bolts

 

Note: These same holes

 

are used for securing the

Fig. 1

stove in mobile home

installation.

 

 

Rear Cover

 

Panels

Unpacking

The P43 is bolted (1/4 x 1" hex head bolts) to the skid to prevent movement during shipping.

To free the stove from the skid you must remove the hold-down bolts in the rear of the pedestal base.

Removing rear cover panels

The rear cover panels are secured to the stove with three bolts each. Two ot the bolts need only be loosened, not removed, to remove the panels. It is recommended that the rear covers are installed after the unit is in place and the vent pipe is installed, to prevent contact with hot or moving parts.

Firebrick

Install the firebrick horizontally on the angle bracket above the burnpot.

Flame Guide

Install the cast iron flame guide on top of the burn pot. Make sure that the flame guide is fully seated on the vertical sides of the burn pot and that the back of the guide rests against the body of the stove.

INSTALL EXHAUST VENT AT CLEARANCES SPECIFIED BY THE MANUFACTURER. Most pellet vent pipe requires a minimum of 3" of clearance to combustible materials allthough some can be installed at 1" clearance.

P43 Pellet Stove

Image 5
Contents Safety Notice Installation & Operating ManualWHI Introduction Table of ContentsImportant Notes Unpacking Assembly and InstallationRemoving rear cover panels FirebrickInstalling InstallationAddition, the following must be observed With outside air installed, 6 feetVenting Vent Pipe VentingOutside Air Direct Vent Wall Passthrough Kit#2 Preferred method #1 Preferred methodFireplace chimney #4 Installing into an existing chimney#5 Installing into an existing #7 Installing into an existing chimney #6 Installing into an existing fireplace chimney#8 Installing through the ceiling Minimum flue vent configurationP43 Automatic Ignition ESP Control Status light error messagesP43 Automatic IGNITION/OPERATION Room Temperature ModeShut Down Procedure Stove Temperature ModeFeed Adjuster Knob Flame Guide SeeHint #7 P43 Automatic Start UPP43 Manual IGNITION/Operation Manual Stove Temperature ModeP43 Manual Start UP Igniter Switch toMANUAL down positionLow Draft Voltage Adjustment P43 Low Draft Voltage AdjustmentRear Shields Room Sensor and Rear Shield InstallationRoom Sensor Installation Cleaning the Door Glass MaintenanceCleaning Removing AshesSoot and Fly Ash Burn Pot Cleaning and Maintenance P43 Maintenance Burn PotPellet Fines will build up in this area P43 Maintenance Cleaning the Feeder BodyCleaning Burn Pot P43 Trouble-ShootingP43 Feeder 28.5 P43 Specifications12.375 Options P43 Wiring Diagram Description Part Number P43 Parts ListHarman Gold Warranty

P43 specifications

The Harman Stove Company P43 is a sophisticated pellet stove renowned for its efficiency, versatility, and modern design. Tailored for homeowners who seek both functionality and aesthetic appeal, the P43 offers a compelling option for heating spaces while contributing to an environmentally friendly lifestyle.

At the heart of the P43 is its impressive heating capacity. It can warm areas up to 1,200 square feet, making it suitable for a variety of home sizes. Its heat output ranges from a low of 8,200 BTUs to a maximum of 43,000 BTUs, allowing users to customize heating levels according to their needs. This adaptability is further enhanced by the unit's easy-to-use control settings that enable precise adjustments for different heating requirements and comfort levels.

One standout feature of the P43 is its efficient heat exchanger system. This technology promotes optimal combustion, ensuring that the maximum amount of heat is produced while minimizing waste. As a result, not only does this contribute to cost-effective heating, but it also enhances the stove's environmental performance by reducing emissions. The P43 is certified by the EPA, confirming its compliance with stringent environmental standards.

The P43 also integrates advanced automation technologies, such as Touch Control Technology, which simplifies the operation of the stove. Users can easily manage settings through a digital interface, allowing for setting timers, adjusting burn rates, and monitoring fuel levels. This level of automation makes it particularly appealing for tech-savvy homeowners who appreciate convenience in their heating solutions.

Another defining characteristic of the P43 is its design. With a sleek, modern look, the pellet stove is available in different finishes, allowing it to seamlessly blend into various home decors. The window remains large and unobstructed, providing a clear view of the fire and enhancing the ambiance of any room.

Additionally, Harman’s renowned build quality ensures that the P43 is not only functional but also durable. Constructed from high-quality materials, the stove is designed to offer long-lasting performance. The unit's efficient fuel feeding system minimizes the need for constant refueling, further enhancing its usability.

Overall, the Harman Stove Company P43 represents a perfect fusion of technology, efficiency, and design. Its strong performance, user-friendly interface, and aesthetic appeal make it a leading choice for those who prioritize comfort and sustainability in their home heating solutions.