Harman Stove Company P43 owner manual Installation, Installing

Page 6
Fig. 6
32½" minimum

Installation

Installing

Place the stove on a noncombustible floor protector that extends a minimum of 6 inches to the front, (mea- sured from the glass) 6 inches to the sides and 1 inch to the rear of the hopper. In some places, it is required that floor protection be installed under any horizontal venting.The minimum floor protector material is 20 gauge sheet metal. Other floor protector materials are ceramic tile, stone, brick, etc.

Place the stove away from combustible walls at least as far as shown in Figures 3,4 and 5. Note the difference in side wall clearance with and without side shields.

Note that the clearances shown are minimum for safety but do not leave much room for access when cleaning or servicing.

Connect the power cord to a 120 V.A.C. 60Hz grounded receptacle. (A surge protector is recom- mended to protect the circuit board.) If the voltage entering your home is below 116 volts your stove may not work properly. Also be sure that the polarity of the outlet that the stove is plugged into is correct.

Prior to installing the flue pipe, connect a draft meter. (The draft meter must have a minimum range of 0-

.5.)Record the first reading. Connect flue pipe to stove and be sure all doors and windows in the home are closed. Record the second draft reading_______. If

the second reading is more than .05" lower than the first reading, check for possible restrictions or the need for outside air (see page 9). For more information on the draft test procedure, refer to Page 20.

Mobile Home Installation

When installing this unit in a mobile home, several requirements must be followed:

1.The unit must be bolted to the floor. This can be done with 1/4" lag screws through the 2 holes in the base plate.

2.The unit must also be connected to outside air. See page 9.

3.Floor protection and clearances must be followed as shown.

4.Unit must be grounded to the metal frame of the mobile home.

CAUTION: This appliance must be vented to the outside.

Due to high temperatures, the stove should be placed out of traffic and away from furniture and draperies.

Children and adults should be alerted to the hazards of high surface temperatures and should stay away to avoid burns to skin and/or clothing.

Young children should be carefully supervised when they are in the same room as the stove.

Clothing and other flammable materials should not be placed on or near this unit.

WARNING

Mobile/Manufactured Home Standards

Do Not Allow Installation In Rooms

Designated For Sleeping.

9"

9"

9" With or Without Side Shields

Fig. 3

10"

Fig. 4

2"

16"

Fig. 5

Floor Protection must be 2 inches to each side, 6 inches to the front, and 1 inch to the back of the stove. Floor Protector minimum: 32½" wide x 33" deep.

minimum33"

 

1"

6"

6"

 

 

 

 

 

6"(measured

 

 

from glass)

P43 Pellet Stove

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Installation & Operating Manual Safety NoticeWHI Table of Contents IntroductionImportant Notes Removing rear cover panels Assembly and InstallationUnpacking FirebrickInstallation InstallingWith outside air installed, 6 feet VentingAddition, the following must be observed Venting Vent PipeDirect Vent Wall Passthrough Kit Outside Air#1 Preferred method #2 Preferred method#4 Installing into an existing chimney #5 Installing into an existingFireplace chimney #6 Installing into an existing fireplace chimney #7 Installing into an existing chimneyMinimum flue vent configuration #8 Installing through the ceilingStatus light error messages P43 Automatic Ignition ESP ControlRoom Temperature Mode P43 Automatic IGNITION/OPERATIONStove Temperature Mode Feed Adjuster KnobShut Down Procedure P43 Automatic Start UP Flame Guide SeeHint #7Manual Stove Temperature Mode P43 Manual IGNITION/OperationIgniter Switch toMANUAL down position P43 Manual Start UPP43 Low Draft Voltage Adjustment Low Draft Voltage AdjustmentRoom Sensor and Rear Shield Installation Room Sensor InstallationRear Shields Cleaning MaintenanceCleaning the Door Glass Removing AshesSoot and Fly Ash P43 Maintenance Burn Pot Burn Pot Cleaning and MaintenanceP43 Maintenance Cleaning the Feeder Body Pellet Fines will build up in this areaP43 Trouble-Shooting Cleaning Burn PotP43 Feeder P43 Specifications 12.37528.5 Options P43 Wiring Diagram P43 Parts List Description Part NumberHarman Gold Warranty

P43 specifications

The Harman Stove Company P43 is a sophisticated pellet stove renowned for its efficiency, versatility, and modern design. Tailored for homeowners who seek both functionality and aesthetic appeal, the P43 offers a compelling option for heating spaces while contributing to an environmentally friendly lifestyle.

At the heart of the P43 is its impressive heating capacity. It can warm areas up to 1,200 square feet, making it suitable for a variety of home sizes. Its heat output ranges from a low of 8,200 BTUs to a maximum of 43,000 BTUs, allowing users to customize heating levels according to their needs. This adaptability is further enhanced by the unit's easy-to-use control settings that enable precise adjustments for different heating requirements and comfort levels.

One standout feature of the P43 is its efficient heat exchanger system. This technology promotes optimal combustion, ensuring that the maximum amount of heat is produced while minimizing waste. As a result, not only does this contribute to cost-effective heating, but it also enhances the stove's environmental performance by reducing emissions. The P43 is certified by the EPA, confirming its compliance with stringent environmental standards.

The P43 also integrates advanced automation technologies, such as Touch Control Technology, which simplifies the operation of the stove. Users can easily manage settings through a digital interface, allowing for setting timers, adjusting burn rates, and monitoring fuel levels. This level of automation makes it particularly appealing for tech-savvy homeowners who appreciate convenience in their heating solutions.

Another defining characteristic of the P43 is its design. With a sleek, modern look, the pellet stove is available in different finishes, allowing it to seamlessly blend into various home decors. The window remains large and unobstructed, providing a clear view of the fire and enhancing the ambiance of any room.

Additionally, Harman’s renowned build quality ensures that the P43 is not only functional but also durable. Constructed from high-quality materials, the stove is designed to offer long-lasting performance. The unit's efficient fuel feeding system minimizes the need for constant refueling, further enhancing its usability.

Overall, the Harman Stove Company P43 represents a perfect fusion of technology, efficiency, and design. Its strong performance, user-friendly interface, and aesthetic appeal make it a leading choice for those who prioritize comfort and sustainability in their home heating solutions.
Top Page Image Contents