Stove Temperature Mode

P43 AUTOMATIC IGNITION/OPERATION

In the Stove Temperature Mode and with the igniter toggle switch in the Auto position, the stove will light automatically and can be adjusted to the desired setting using the same temperature control dial as is used in the Room Temperature Mode. The heat output and fuel consumption will remain constant regardless of room temperature. The settings from 1 to 7 on the inner ring of the temperature dial provide for relative heat output settings with 1 being low and 7 being the maximum.

In Stove Temperature Mode, the stove will not automatically shut off unless the stove runs out of fuel or is turned off.

Never pull the plug to shut down the stove. This will stop the combustion blower and smoke will escape through window and door gaskets.

When the igniter toggle switch is set to manual in this mode, the distribution blower will not turn on with a temperature dial setting from 1 to 5. The advantage of this mode is to allow the operator to have a large viewing

fire without blowing extra heat into the room.

During manual operation, with the temperature dial set at #5 or less, the distribution fan will not operate. A #5 on the temperature dial and a #5 on the feed adjuster is approximately 80% output. It is not necessary to operate the distribution blower below this point. Therefore, the

control allows a higher burn rate ( a larger viewing fire)

without an excess of hot air blowing into the room. An example of when to use the Manual Stove Tempera-

ture Mode is if you want to watch a large fire and the

room is already up to temperature. The Stove Tempera-

ture Mode allows you to have a larger fire and a lower

sound level, without the distribution blower.

NOTE: During the use of this mode, if you keep increasing the temperature dial setting to increase the fire size, the distribution blower will automati- cally come on when the ESP Temperature reaches 350o F, or 81% output.

Feed Adjuster Knob

For most premium grade pellet fuels the Feed Adjuster Knob should be set at 4. If higher ash fuels are used the setting should be increased to 5 or 6. Also higher settings are required if you would like to get the maximum heat output from the stove. At the maximum burn rate (with the temperature dial on 7/90° and the feed adjuster at 6) there should be 1" or more of ash on the front of the burn pot. If there is less than 1" of ash, turn the feed adjuster knob down to a lower setting.

Shut Down Procedure

The best way to shut down the stove is to simply let it run out of pellets. The stove will shut down automatically. Alternatively, you can turn the Mode Selector to “off”. This will cause the fire to gradually die down and go out. The fire will not go out immediately and may take more than an hour to fully shut down.

If the stove is left to run out of fuel, you may get a 6 blink status light. If this happens simply reset the control board by turning the mode selector to OFF and back ON.

Stove Temperature Mode

The setting above will produce continuous medium heat output with the distribution blower at low speed.

The setting above will produce continuous maximum heat output with the distribution blower at full speed.

16P43 Pellet Stove

P43 specifications

The Harman Stove Company P43 is a sophisticated pellet stove renowned for its efficiency, versatility, and modern design. Tailored for homeowners who seek both functionality and aesthetic appeal, the P43 offers a compelling option for heating spaces while contributing to an environmentally friendly lifestyle.

At the heart of the P43 is its impressive heating capacity. It can warm areas up to 1,200 square feet, making it suitable for a variety of home sizes. Its heat output ranges from a low of 8,200 BTUs to a maximum of 43,000 BTUs, allowing users to customize heating levels according to their needs. This adaptability is further enhanced by the unit's easy-to-use control settings that enable precise adjustments for different heating requirements and comfort levels.

One standout feature of the P43 is its efficient heat exchanger system. This technology promotes optimal combustion, ensuring that the maximum amount of heat is produced while minimizing waste. As a result, not only does this contribute to cost-effective heating, but it also enhances the stove's environmental performance by reducing emissions. The P43 is certified by the EPA, confirming its compliance with stringent environmental standards.

The P43 also integrates advanced automation technologies, such as Touch Control Technology, which simplifies the operation of the stove. Users can easily manage settings through a digital interface, allowing for setting timers, adjusting burn rates, and monitoring fuel levels. This level of automation makes it particularly appealing for tech-savvy homeowners who appreciate convenience in their heating solutions.

Another defining characteristic of the P43 is its design. With a sleek, modern look, the pellet stove is available in different finishes, allowing it to seamlessly blend into various home decors. The window remains large and unobstructed, providing a clear view of the fire and enhancing the ambiance of any room.

Additionally, Harman’s renowned build quality ensures that the P43 is not only functional but also durable. Constructed from high-quality materials, the stove is designed to offer long-lasting performance. The unit's efficient fuel feeding system minimizes the need for constant refueling, further enhancing its usability.

Overall, the Harman Stove Company P43 represents a perfect fusion of technology, efficiency, and design. Its strong performance, user-friendly interface, and aesthetic appeal make it a leading choice for those who prioritize comfort and sustainability in their home heating solutions.