Harman Stove Company Conquest Gas Stove manual Optional Blower, Installation

Page 19

Only For Qualified Installers

INSTALLATION (Options)

19

Power Cord

Blower Assembly

Speed Control Knob

Optional Blower

The Blower Kit (Part # 1-00-09102) includes a blower assembly ready to bolt to the left side of the stove and a blower chamber cover.

The blower has a variable speed control knob to adjust the blower speed as desired. A special switch is used to automatically start the blower when the stove temperature is hot enough to blow warm air. This switch will also stop the blower when the stove temperature drops below the point that warm air is available.

Installation

1.Open the left side panel.

2.Remove the four screws from the left side of the firebox with a 5/16” socket.

3.Place the blower as shown and start the top screw. This will hold the blower in place and make it easier to install the other three screws.

4.Route the power cord rearward between the side panel and the pedestal and plug into a 120 volt outlet.

5.Open the right side panel and remove the two screws on the right side of the firebox.

6.Use the two screws to fasten the blower cham- ber cover plate to the firebox. This plate pre- vents air from the blower escaping from the air chamber.

7.Close side panels.

Operation

Turn the speed control knob clockwise until it clicks. This is the full speed position. Turning the knob farther in the clockwise direction will gradu-

ally reduce the blower speed. To turn the blower “OFF” turn the knob counterclockwise until it clicks.

This blower is equipped with a three-prong (grounding) plug for protection against shock hazard and should be plugged directly into a properly grounded three-prong receptacle. Do not cut or remove the grounding prong from the plug.

Blower Chamber Cover

Image 19
Contents Harman Conquest Gas Stove Safety NoticeFor Your Safety What to do if YOU Smell GAS Table of Contents Introduction4 Operation OPERATION5Pilot Flames OPERATION6Ratings Natural SPECIFICATIONS7Corner Clearances SpecificationsAlcove Clearances Installation Part Numbers for SimpsonDura-Vent Pipe and Fittings Use Only Approved Venting8 x Description Rear Vent ConquestRequirements for Terminating the Venting Damper Settings INSTALLATION13Feet Natural Gas Conversion Kit Changing to Natural GasNatural Gas Kit INSTALLATION15 Deflector plate INSTALLATION16Log Placement Ember PlacementTile Kit Installing TilesConnecting the Optional Thermostat Installation OptionsRemote Control Kit Optional Blower Replacing the Gasket MaintenanceCleaning the Glass Removing the Glass FrontInspecting the Venting MAINTENANCE21Cleaning the Log Set and Firebox Cleaning the BurnersOptional Blower Wiring MAINTENANCE22Diagram 120 Volt WHI # Model ConquestGlass gasket 7’/unit PartsBurner Parts MAINTENANCE25Replace YesBad Replace Piezo Ignitor Turn on gas valve Replenish supplyReplace Valve Trouble ShootingGood Check inlet pressureIs Pilot lit BadInput Btu/h 27,500 Converted ByDate Optional Blower LabelOrifice Size 11 WCYear Limited Warranty Commercial Harman Gold WarrantyHarman Gold Warranty Year Transferable Limited Warranty Residential

Conquest Gas Stove specifications

The Harman Stove Company Conquest Gas Stove represents a pinnacle of design and technology in home heating solutions. This high-efficiency gas stove is engineered to deliver not only warmth but also aesthetics, making it an attractive addition to any living space.

One of the standout features of the Conquest Gas Stove is its advanced heating capability. With its large firebox, this stove can produce an impressive 44,000 BTUs, ensuring ample warmth for larger rooms or open-concept areas. The stove is designed to provide consistent heat over extended periods, creating a cozy atmosphere regardless of the outdoor temperature.

Efficiency is a key characteristic of the Conquest model, boasting an impressive efficiency rating of up to 85%. This means that more of the gas consumed is converted into usable heat, allowing homeowners to save on energy costs while enjoying a sustained warmth. The stove features a sealed combustion system that draws air from outside, providing a clean burn and enhancing energy efficiency.

The Harman Conquest Gas Stove is also equipped with innovative technology, including adjustable heat output and variable blower speeds that allow users to customize their heating needs. The easy-to-use digital control provides precise temperature adjustments, ensuring that the room temperature can be maintained at the desired level effortlessly.

Aesthetically, the Conquest Gas Stove is designed to fit seamlessly into various home decor styles. Its attractive cast iron body is available in multiple finishes, providing versatility to complement any interior. The large viewing window, framed by stylish cast iron, enhances the beauty of the flames, creating an enchanting visual centerpiece in any living area.

Safety is another critical aspect of the Conquest Gas Stove. It comes equipped with advanced safety features, including an automatic shut-off valve and a safety thermocouple that ensures the stove operates safely under all conditions.

In conclusion, the Harman Stove Company Conquest Gas Stove combines high efficiency, modern technology, and exquisite design to deliver a top-tier heating solution. With its robust output, customizability, aesthetic appeal, and safety features, the Conquest model exemplifies what homeowners can expect from a premium gas stove. It is a perfect choice for those looking to enhance their heating system while enjoying the timeless charm of traditional stove design.