Avalon Stoves 1190 owner manual Standard vs. Cook-Top Installations, Installation Considerations

Page 17

Fireplace Insert Installation (for qualified installers only)

17

SAFETY NOTICE:

Please read this entire manual before you install and use your new room heater. Failure to follow instructions may result in property damage, bodily injury, oreven death. Contact local building orfire officials about restrictions and installation inspection requirements in yourarea.

Planning The Installation

We suggest that you have an authorized Travis Industries dealer install your fireplace insert. If you install the fireplace insert yourself, your authorized dealer should review your installation plans.

Check with local building officials for any permits required for installation of this fireplace insert and notify your insurance company before proceeding with installation.

Preparation for Installation

Check for damage to the exterior of the fireplace insert (dents should be reported, scratches can be fixed by applying touch up paint).

Check the interior of the firebox (replace cracked firebrick and make sure baffle is in place).

The fireplace insert can be lightened by removing the firebricks and baffle (pg 36) - replace before operation.

Additional Accessories Needed for Installation

Surround Panels (see page 44)

Standard vs. Cook-Top Installations

The top air chamber extension is shipped separately with the heater (see the following page for details). When installed, the unit is considered a “Standard Model” for Insert Placement and Fireplace Requirements. If it is not installed, the unit is considered a “Cook-Top Model” for Insert Placement and Fireplace Requirements.

Installation Considerations

Installation Type

Considerations

 

 

Insert with Positive Flue (Full Reline)

• Utilizes existing masonry fireplace

(Page 23)

• Provides best draft

• Easiest to clean

 

Insert with Direct Connect Flue

• Utilizes existing masonry fireplace

(Page 23)

• Provides good draft

• Requires fireplace block-off plate - see page 22

 

Insert with Face Seal Connection

• Utilizes existing masonry fireplaces with cross section

(Page 24)

of 28" to 144"

• Provides marginal draft

 

NOTE: Before installing verify with local building

• Easiest to install

officials that this type of installation is

• Requires the optional surround panels and insulation

approved in your area.

(see "Surround Panels" on page 44).

© Travis Industries

93508061

4050526

Image 17
Contents Olympic Save Your Bill of Sale 2IntroductionIntroduction Important Information Table of Contents Ashes Safety PrecautionsMobile Travis Industries, Inc. grants no warranty, implied orFeatures & Specifications Preparation for Installation Planning The InstallationAdditional Accessories Needed for Installation Stove Installation ConsiderationsMinimum Clearance Singlewall Reduced Connector Stove Placement RequirementsFloor Protection Requirements ClearancesTop View Corner Installation Top View Straight InstallationPerformance Chimney RequirementsDrafting Outside Air Requirements Chimney Termination RequirementsAlcove Installation Requirements Mobile Home Requirements Not the connector manufacturers clearanceCathedral Ceiling with a Factory Built Chimney Standard Ceiling with a Factory Built ChimneyHearth Stove Positive Connection Exterior Factory Built ChimneyInterior or Exterior Masonry Chimney Hearth Stove Direct ConnectionInstallation Considerations Standard vs. Cook-Top InstallationsTop Air Chamber Extension Fireplace Requirements Fireplace SizeMasonry Fireplace Requirements Insert Placement RequirementsHearth Requirements Drafting Performance Leveling Bolt InstallationBlock-Off Plate Template Block-Off Plate InstallationInsert with Direct Connection Masonry Fireplace Insert with Positive ConnectionInsert with Face Seal Connection Operating Your Appliance Safety NoticeBefore Your First Fire Opening the DoorBypass Operation Starting a Fire Ash Removal Adjusting the Burn RateApproximate Air Control Settings Re-Loading the Stove Optional Blower OperationOvernight Burn Normal Operating SoundsHints for Burning Why Dry Wood is KeySelecting Wood Wood Cutting and StorageTroubleshooting Clean the Glass if necessary Daily Maintenance while stove is in useMaintaining Your Appliance Remove Ash if necessaryCreosote Formation and Need for Removal Monthly Maintenance while appliance is in useDoor and Glass Inspection Cleaning the Air Duct and Blower if applicable Yearly MaintenanceTouch Up Paint Firebrick and Baffle InspectionReplacing the Glass Door PartsReplacing the Door Gasket Replacing the Door HandleFirebox Parts Floor and Side Firebrick Removal & ReplacementAir Tube Removal & Replacement Baffle Removal & ReplacementYears 1 & 2 Coverage Parts & Labor Limited 7 Year WarrantyYears 3 Through 5 Coverage Parts & Labor Years 6 & 7 Coverage Parts onlyListing Label Listing InformationPedestal Optional EquipmentOutside AIR Equipment Outside Air Installation for wood stoves onlyInstall the wire clip following the directions below Rear Blower Installation Part numberOutside Air Boot Installation Part number Z e Size on Insert w trim Surround Panels see s belowFront Blower To Switch the Power Cord to the Left SideIndex

1190 specifications

Avalon Stoves has long been recognized for its commitment to quality, efficiency, and performance in the realm of home heating. Among its stellar offerings, the Avalon Stoves 1190 stands out as a testament to modern innovation and classic design. This wood-burning stove caters to both functionality and aesthetics, making it an ideal addition to any home.

One of the main features of the Avalon 1190 is its impressive heating capacity. With the ability to produce up to 70,000 BTUs, this stove is capable of heating large spaces, making it perfect for open-concept layouts or larger living areas. The stove's firebox is designed to accommodate logs up to 18 inches, allowing for longer burn times and less frequent reloading.

In addition to its heating capabilities, the Avalon 1190 incorporates advanced technologies that enhance its efficiency. One notable feature is the clean-burn technology, which significantly reduces emissions while maximizing heat output. This technology not only promotes a healthier environment but also aligns with eco-friendly practices, creating a more sustainable heating option for homeowners.

The Avalon 1190 is also equipped with a secondary combustion system, which ensures that more of the wood’s energy is utilized during the burn process. This results in hotter fires and minimal smoke production, further contributing to its efficient performance. The stove's design also includes a built-in air wash system that helps keep the glass clean, allowing for a clear view of the mesmerizing flames.

Another characteristic that sets the Avalon 1190 apart is its aesthetic appeal. With a sleek and contemporary design, the stove is available in several finishes, including classic black, cast iron, and even a stylish porcelain enamel. This versatility ensures that it can seamlessly integrate into any home décor, from rustic to modern settings.

Moreover, the Avalon 1190 comes with a reliable warranty, underscoring the manufacturer's confidence in the product’s durability. Constructed with high-quality materials, this wood stove is built to last, providing warmth and comfort for years to come.

In conclusion, the Avalon Stoves 1190 is a perfect blend of high performance, innovative technology, and elegant design. Whether it’s for heating a cozy living room or creating an inviting ambiance, the Avalon 1190 remains a top choice for discerning homeowners seeking a dependable wood-burning solution. Its efficient heating capabilities, coupled with eco-friendly features, make it a model of contemporary living that respects both comfort and the environment.