Avalon Stoves 1190 Planning The Installation, Preparation for Installation, Packing List

Page 7

Stove Installation (for qualified installers only)

7

SAFETY NOTICE:

Please read this entire manual before you install and use your new room heater. Failure to follow instructions may result in property damage, bodily injury, oreven death. Contact local building orfire officials about restrictions and installation inspection requirements in yourarea.

Planning The Installation

We suggest that you have an authorized Travis Industries dealer install your stove. If you install the stove yourself, your authorized dealer should review your installation plans.

Check with local building officials for any permits required for installation of this stove and notify your insurance company before proceeding with installation.

Preparation for Installation

Check for damage to the exterior of the stove (dents should be reported, scratches can be fixed by applying touch up paint).

Check the interior of the firebox (replace cracked firebrick and make sure baffle is in place).

The stove can be lightened by removing the firebricks and baffle (pg 36) - replace before operation.

Additional Accessories Needed for Installation

Legs or Pedestal

Packing List

Top Air Chamber Extension (used for inserts only)

Damper Rod (for the Top Air Chamber Extension)

(4) Screws (for the Top Air Chamber Extension)

Pull Tool (used to adjust the damper when hot)

Stove Installation Considerations

The table below details the six most common types of installations and the considerations for each type. Alternative methods of installation are available if they comply with local building codes.

Installation Type

Considerations

 

 

Standard Ceiling with a Factory Built Chimney

Requires ceiling and roof penetration

(Page 14)

Provides best draft

 

 

Cathedral Ceiling with a Factory Built Chimney

Cathedral style chimney support required

(Page 14)

Provides best draft

 

 

Exterior Factory Built Chimney

Uses two elbows to route chimney outside

(Page 15)

Exterior chimney is hidden from the room

 

Elbows reduce draft

 

Optional exterior chase reduces cold air blockage

Hearth Stove Positive Connection

Utilizes existing masonry chimney

(Page 15)

Provides good draft due to full reline

 

Easier to clean than direct or horizontal hearth stove

Hearth Stove Direct Connection

Utilizes existing masonry chimney

(Page 16)

Requires construction of a "block-off plate"

 

Draft reduced due to elbows & chimney cross section

Interior Masonry Chimney

Utilizes existing masonry chimney

(Page 16)

 

 

 

 

 

© Travis Industries

93508061

4050526

Image 7
Contents Olympic Introduction Important Information 2IntroductionSave Your Bill of Sale Table of Contents Ashes Safety PrecautionsMobile Travis Industries, Inc. grants no warranty, implied orFeatures & Specifications Stove Installation Considerations Planning The InstallationPreparation for Installation Additional Accessories Needed for InstallationClearances Stove Placement RequirementsMinimum Clearance Singlewall Reduced Connector Floor Protection RequirementsTop View Corner Installation Top View Straight InstallationDrafting Chimney RequirementsPerformance Outside Air Requirements Chimney Termination RequirementsAlcove Installation Requirements Mobile Home Requirements Not the connector manufacturers clearanceCathedral Ceiling with a Factory Built Chimney Standard Ceiling with a Factory Built ChimneyHearth Stove Positive Connection Exterior Factory Built ChimneyInterior or Exterior Masonry Chimney Hearth Stove Direct ConnectionInstallation Considerations Standard vs. Cook-Top InstallationsTop Air Chamber Extension Fireplace Requirements Fireplace SizeHearth Requirements Insert Placement RequirementsMasonry Fireplace Requirements Drafting Performance Leveling Bolt InstallationBlock-Off Plate Template Block-Off Plate InstallationInsert with Direct Connection Masonry Fireplace Insert with Positive ConnectionInsert with Face Seal Connection Opening the Door Safety NoticeOperating Your Appliance Before Your First FireBypass Operation Starting a Fire Approximate Air Control Settings Adjusting the Burn RateAsh Removal Normal Operating Sounds Optional Blower OperationRe-Loading the Stove Overnight BurnWood Cutting and Storage Why Dry Wood is KeyHints for Burning Selecting WoodTroubleshooting Remove Ash if necessary Daily Maintenance while stove is in useClean the Glass if necessary Maintaining Your ApplianceDoor and Glass Inspection Monthly Maintenance while appliance is in useCreosote Formation and Need for Removal Firebrick and Baffle Inspection Yearly MaintenanceCleaning the Air Duct and Blower if applicable Touch Up PaintReplacing the Door Handle Door PartsReplacing the Glass Replacing the Door GasketFirebox Parts Floor and Side Firebrick Removal & ReplacementAir Tube Removal & Replacement Baffle Removal & ReplacementYears 6 & 7 Coverage Parts only Limited 7 Year WarrantyYears 1 & 2 Coverage Parts & Labor Years 3 Through 5 Coverage Parts & LaborListing Label Listing InformationPedestal Optional EquipmentOutside AIR Equipment Outside Air Installation for wood stoves onlyInstall the wire clip following the directions below Rear Blower Installation Part numberOutside Air Boot Installation Part number Z e Size on Insert w trim Surround Panels see s belowFront Blower To Switch the Power Cord to the Left SideIndex

1190 specifications

Avalon Stoves has long been recognized for its commitment to quality, efficiency, and performance in the realm of home heating. Among its stellar offerings, the Avalon Stoves 1190 stands out as a testament to modern innovation and classic design. This wood-burning stove caters to both functionality and aesthetics, making it an ideal addition to any home.

One of the main features of the Avalon 1190 is its impressive heating capacity. With the ability to produce up to 70,000 BTUs, this stove is capable of heating large spaces, making it perfect for open-concept layouts or larger living areas. The stove's firebox is designed to accommodate logs up to 18 inches, allowing for longer burn times and less frequent reloading.

In addition to its heating capabilities, the Avalon 1190 incorporates advanced technologies that enhance its efficiency. One notable feature is the clean-burn technology, which significantly reduces emissions while maximizing heat output. This technology not only promotes a healthier environment but also aligns with eco-friendly practices, creating a more sustainable heating option for homeowners.

The Avalon 1190 is also equipped with a secondary combustion system, which ensures that more of the wood’s energy is utilized during the burn process. This results in hotter fires and minimal smoke production, further contributing to its efficient performance. The stove's design also includes a built-in air wash system that helps keep the glass clean, allowing for a clear view of the mesmerizing flames.

Another characteristic that sets the Avalon 1190 apart is its aesthetic appeal. With a sleek and contemporary design, the stove is available in several finishes, including classic black, cast iron, and even a stylish porcelain enamel. This versatility ensures that it can seamlessly integrate into any home décor, from rustic to modern settings.

Moreover, the Avalon 1190 comes with a reliable warranty, underscoring the manufacturer's confidence in the product’s durability. Constructed with high-quality materials, this wood stove is built to last, providing warmth and comfort for years to come.

In conclusion, the Avalon Stoves 1190 is a perfect blend of high performance, innovative technology, and elegant design. Whether it’s for heating a cozy living room or creating an inviting ambiance, the Avalon 1190 remains a top choice for discerning homeowners seeking a dependable wood-burning solution. Its efficient heating capabilities, coupled with eco-friendly features, make it a model of contemporary living that respects both comfort and the environment.