Avalon Stoves 1190 owner manual Rear Blower Installation Part number

Page 42

42

Optional Equipment

Rear Blower Installation (Part number 99000138)

The rear blower improves heat transfer by pushing heated air through the convection channel. Operating instructions are described in the section "Blower Operation" on page 29.

1.The stove should be in place with the legs installed prior to installing the rear blower.

2.Follow the directions below to install the thermodisk.

These wires pass through the left side convection channel.

Air

Control

Rod

Thermodisk Assembly

 

Insert the thermodisk

Bend metal up or down

assembly 4" to 5" inside

here to create a snug fit

the convection channel.

3. Install the wire clip following the directions below.

Use a screwdriver to pry out the knock-out.

Slide the wire clip over the edge of the strip of metal between the two knock-outs.

Wire Clip

Snap Disk

Wires

Feed the two snap disk wires into the eye of the wire clip. Remove all slack from the wire, making sure not to dislodge the snap disk. Pinch the eye of the wire clip to secure the wires.

WARNING:

To prevent electrical shock, the wires must be secured so they do not contact the firebox above the convection channel.

4. Attach the blower following the directions below.

Attach the quick-connects

a leading from the snap disk to the quick-connects from the blower (orientation does not matter).

b

The blower attaches to the stove with the three

 

included screws. Use a 3/8” socket driver or wrench.

 

3/8" Nutdriver

NOTE:

Prior to attaching the blower, tuck all excess wire into the area inside the blower.

c

Plug the power cord into a 110 V. outlet after installing the

 

blower.

© Travis Industries

93508061

4050526

Image 42
Contents Olympic 2Introduction Introduction Important InformationSave Your Bill of Sale Table of Contents Safety Precautions AshesTravis Industries, Inc. grants no warranty, implied or MobileFeatures & Specifications Additional Accessories Needed for Installation Planning The InstallationPreparation for Installation Stove Installation ConsiderationsFloor Protection Requirements Stove Placement RequirementsMinimum Clearance Singlewall Reduced Connector ClearancesTop View Straight Installation Top View Corner InstallationChimney Requirements DraftingPerformance Chimney Termination Requirements Outside Air RequirementsAlcove Installation Requirements Not the connector manufacturers clearance Mobile Home RequirementsStandard Ceiling with a Factory Built Chimney Cathedral Ceiling with a Factory Built ChimneyExterior Factory Built Chimney Hearth Stove Positive ConnectionHearth Stove Direct Connection Interior or Exterior Masonry ChimneyStandard vs. Cook-Top Installations Installation ConsiderationsTop Air Chamber Extension Fireplace Size Fireplace RequirementsInsert Placement Requirements Hearth RequirementsMasonry Fireplace Requirements Leveling Bolt Installation Drafting PerformanceBlock-Off Plate Installation Block-Off Plate TemplateInsert with Positive Connection Insert with Direct Connection Masonry FireplaceInsert with Face Seal Connection Before Your First Fire Safety NoticeOperating Your Appliance Opening the DoorBypass Operation Starting a Fire Adjusting the Burn Rate Approximate Air Control SettingsAsh Removal Overnight Burn Optional Blower OperationRe-Loading the Stove Normal Operating SoundsSelecting Wood Why Dry Wood is KeyHints for Burning Wood Cutting and StorageTroubleshooting Maintaining Your Appliance Daily Maintenance while stove is in useClean the Glass if necessary Remove Ash if necessaryMonthly Maintenance while appliance is in use Door and Glass InspectionCreosote Formation and Need for Removal Touch Up Paint Yearly MaintenanceCleaning the Air Duct and Blower if applicable Firebrick and Baffle InspectionReplacing the Door Gasket Door PartsReplacing the Glass Replacing the Door HandleFloor and Side Firebrick Removal & Replacement Firebox PartsBaffle Removal & Replacement Air Tube Removal & ReplacementYears 3 Through 5 Coverage Parts & Labor Limited 7 Year WarrantyYears 1 & 2 Coverage Parts & Labor Years 6 & 7 Coverage Parts onlyListing Information Listing LabelOptional Equipment PedestalOutside Air Installation for wood stoves only Outside AIR EquipmentRear Blower Installation Part number Install the wire clip following the directions belowOutside Air Boot Installation Part number Surround Panels see s below Z e Size on Insert w trimTo Switch the Power Cord to the Left Side Front BlowerIndex

1190 specifications

Avalon Stoves has long been recognized for its commitment to quality, efficiency, and performance in the realm of home heating. Among its stellar offerings, the Avalon Stoves 1190 stands out as a testament to modern innovation and classic design. This wood-burning stove caters to both functionality and aesthetics, making it an ideal addition to any home.

One of the main features of the Avalon 1190 is its impressive heating capacity. With the ability to produce up to 70,000 BTUs, this stove is capable of heating large spaces, making it perfect for open-concept layouts or larger living areas. The stove's firebox is designed to accommodate logs up to 18 inches, allowing for longer burn times and less frequent reloading.

In addition to its heating capabilities, the Avalon 1190 incorporates advanced technologies that enhance its efficiency. One notable feature is the clean-burn technology, which significantly reduces emissions while maximizing heat output. This technology not only promotes a healthier environment but also aligns with eco-friendly practices, creating a more sustainable heating option for homeowners.

The Avalon 1190 is also equipped with a secondary combustion system, which ensures that more of the wood’s energy is utilized during the burn process. This results in hotter fires and minimal smoke production, further contributing to its efficient performance. The stove's design also includes a built-in air wash system that helps keep the glass clean, allowing for a clear view of the mesmerizing flames.

Another characteristic that sets the Avalon 1190 apart is its aesthetic appeal. With a sleek and contemporary design, the stove is available in several finishes, including classic black, cast iron, and even a stylish porcelain enamel. This versatility ensures that it can seamlessly integrate into any home décor, from rustic to modern settings.

Moreover, the Avalon 1190 comes with a reliable warranty, underscoring the manufacturer's confidence in the product’s durability. Constructed with high-quality materials, this wood stove is built to last, providing warmth and comfort for years to come.

In conclusion, the Avalon Stoves 1190 is a perfect blend of high performance, innovative technology, and elegant design. Whether it’s for heating a cozy living room or creating an inviting ambiance, the Avalon 1190 remains a top choice for discerning homeowners seeking a dependable wood-burning solution. Its efficient heating capabilities, coupled with eco-friendly features, make it a model of contemporary living that respects both comfort and the environment.