Avalon Stoves 1190 owner manual Surround Panels see s below, Z e Size on Insert w trim

Page 44

44

Optional Equipment

Surround Panels (see part #'s below)

S i z e

Size on Insert (w trim)

PART #

8"

45 1/4" wide by 28 7/8" high

99300312

10"

49 1/4" wide by 30 7/8" high

99300313

12"

53 1/4" wide by 32 7/8" high

99300314

INSTALLATION INSTRUCTIONS

Avalon Pendleton-45 and Rainier-45:

Remove the brass trim along the top of the stove.

1. With the insert 12” from

the fireplace, install the

side surround panels (see

the directions to the

right).

2. Adjust the position of the

side panels so they are:

1) aligned with the top of

the insert; 2) both the

same distance back from

the front of the insert; 3)

perpendicular to the floor

(use the top panel, if

necessary, to judge

alignment). Tighten the

screws that hold the side

panels in place.

Side

Panel

Button Plugs

(pry out with a screwdriver)

Attach the side panels with the included screws (hint: pre-thread the holes prior to installing the panels).

3. Install the top panel and

trim following the

directions to the right.

5/16" Nutdriver

Insulation Installation (required for face seal installations only)

1.With the insert drawn 6" from the fireplace, glue the insulation strip included with the surround panel kit to the back of the panels using RTV silicon or stove gasket cement. The insulation should be installed so it overlaps the fireplace opening to form a seal between the panels and the fireplace face. Let the silicon or cement dry.

2.Push the insert into the fireplace, allowing the insulation to form a seal between the panels and the fireplace. Use a screwdriver to tuck any exposed insulation behind the panels.

Spring

Clips

Install the top panel so the tabs insert into the joggle clips on the top panel

5/16" Nutdriver

Top Trim

Top

Panel

Micro (1/16”)

Standard

Screwdriver

Top Trim

"L" Bracket

Right Side

Trim

Optional Trim Installation:

Insert one leg of each "L" bracket into the top and side trim piece. Align the trim to form a precise corner, then tighten the two set screws with a small standard screwdriver. Slide the trim over the panels. Place the spring clips behind the panels at the locations shown. This keeps the trim tight against the panel.

Optional Knock-Out

An optional knock-out is provided on both sides if the power cord is routed behind the surround panel.

© Travis Industries

93508061

4050526

Image 44
Contents Olympic Save Your Bill of Sale 2IntroductionIntroduction Important Information Table of Contents Safety Precautions AshesTravis Industries, Inc. grants no warranty, implied or MobileFeatures & Specifications Planning The Installation Preparation for InstallationAdditional Accessories Needed for Installation Stove Installation ConsiderationsStove Placement Requirements Minimum Clearance Singlewall Reduced ConnectorFloor Protection Requirements ClearancesTop View Straight Installation Top View Corner InstallationPerformance Chimney RequirementsDrafting Chimney Termination Requirements Outside Air RequirementsAlcove Installation Requirements Not the connector manufacturers clearance Mobile Home RequirementsStandard Ceiling with a Factory Built Chimney Cathedral Ceiling with a Factory Built ChimneyExterior Factory Built Chimney Hearth Stove Positive ConnectionHearth Stove Direct Connection Interior or Exterior Masonry ChimneyStandard vs. Cook-Top Installations Installation ConsiderationsTop Air Chamber Extension Fireplace Size Fireplace RequirementsMasonry Fireplace Requirements Insert Placement RequirementsHearth Requirements Leveling Bolt Installation Drafting PerformanceBlock-Off Plate Installation Block-Off Plate TemplateInsert with Positive Connection Insert with Direct Connection Masonry FireplaceInsert with Face Seal Connection Safety Notice Operating Your ApplianceBefore Your First Fire Opening the DoorBypass Operation Starting a Fire Ash Removal Adjusting the Burn RateApproximate Air Control Settings Optional Blower Operation Re-Loading the StoveOvernight Burn Normal Operating SoundsWhy Dry Wood is Key Hints for BurningSelecting Wood Wood Cutting and StorageTroubleshooting Daily Maintenance while stove is in use Clean the Glass if necessaryMaintaining Your Appliance Remove Ash if necessaryCreosote Formation and Need for Removal Monthly Maintenance while appliance is in useDoor and Glass Inspection Yearly Maintenance Cleaning the Air Duct and Blower if applicableTouch Up Paint Firebrick and Baffle InspectionDoor Parts Replacing the GlassReplacing the Door Gasket Replacing the Door HandleFloor and Side Firebrick Removal & Replacement Firebox PartsBaffle Removal & Replacement Air Tube Removal & ReplacementLimited 7 Year Warranty Years 1 & 2 Coverage Parts & LaborYears 3 Through 5 Coverage Parts & Labor Years 6 & 7 Coverage Parts onlyListing Information Listing LabelOptional Equipment PedestalOutside Air Installation for wood stoves only Outside AIR EquipmentRear Blower Installation Part number Install the wire clip following the directions belowOutside Air Boot Installation Part number Surround Panels see s below Z e Size on Insert w trimTo Switch the Power Cord to the Left Side Front BlowerIndex

1190 specifications

Avalon Stoves has long been recognized for its commitment to quality, efficiency, and performance in the realm of home heating. Among its stellar offerings, the Avalon Stoves 1190 stands out as a testament to modern innovation and classic design. This wood-burning stove caters to both functionality and aesthetics, making it an ideal addition to any home.

One of the main features of the Avalon 1190 is its impressive heating capacity. With the ability to produce up to 70,000 BTUs, this stove is capable of heating large spaces, making it perfect for open-concept layouts or larger living areas. The stove's firebox is designed to accommodate logs up to 18 inches, allowing for longer burn times and less frequent reloading.

In addition to its heating capabilities, the Avalon 1190 incorporates advanced technologies that enhance its efficiency. One notable feature is the clean-burn technology, which significantly reduces emissions while maximizing heat output. This technology not only promotes a healthier environment but also aligns with eco-friendly practices, creating a more sustainable heating option for homeowners.

The Avalon 1190 is also equipped with a secondary combustion system, which ensures that more of the wood’s energy is utilized during the burn process. This results in hotter fires and minimal smoke production, further contributing to its efficient performance. The stove's design also includes a built-in air wash system that helps keep the glass clean, allowing for a clear view of the mesmerizing flames.

Another characteristic that sets the Avalon 1190 apart is its aesthetic appeal. With a sleek and contemporary design, the stove is available in several finishes, including classic black, cast iron, and even a stylish porcelain enamel. This versatility ensures that it can seamlessly integrate into any home décor, from rustic to modern settings.

Moreover, the Avalon 1190 comes with a reliable warranty, underscoring the manufacturer's confidence in the product’s durability. Constructed with high-quality materials, this wood stove is built to last, providing warmth and comfort for years to come.

In conclusion, the Avalon Stoves 1190 is a perfect blend of high performance, innovative technology, and elegant design. Whether it’s for heating a cozy living room or creating an inviting ambiance, the Avalon 1190 remains a top choice for discerning homeowners seeking a dependable wood-burning solution. Its efficient heating capabilities, coupled with eco-friendly features, make it a model of contemporary living that respects both comfort and the environment.