Avalon Stoves 1190 owner manual Optional Blower Operation, Re-Loading the Stove, Overnight Burn

Page 29

Operating Your Appliance

29

Optional Blower Operation

The blower will turn on once the stove is up to temperature. This is typically 15 to 30 minutes after starting the fire. Follow the directions below to alter the blower speed.

OFF

HIGH

LOW

Turn the dial all the way counter-

The high position is all the way counter-

Turn the dial all the

clockwise until it clicks off.

clockwise, without clicking off.

way clockwise.

OFF

HI

LO

 

BLOWER

 

CONTROL

 

OFF

HI

LO

 

BLOWER

 

CONTROL

 

OFF

HI

LO

 

BLOWER

 

CONTROL

 

The blower may be used to affect heat output (i.e.: to reduce heat output, turn the blower down).

Route the power cord in a location where it will not come in contact with the appliance or become hot.

Re-Loading the Stove

Follow the directions below to minimize smoke spillage while re-loading the stove.

1.Open the air control all the way (push it in). Open the bypass (pull it out).

2.Open the door slightly. Let the airflow inside the firebox to stabilize before opening the door fully.

3.Load wood onto the fire.

Overnight Burn

This stove is large enough to accommodate burn times up to eight hours. Follow the steps below to achieve an overnight burn.

1.Move the air control to high burn and let the stove become hot (burn for approximately 15 minutes).

2.Load as much wood as possible. Use large pieces if possible.

3.Let the stove burn on high for 15 minutes to keep the stove hot, then turn the air control to low.

4.In the morning the stove should still be hot, with embers in the coal bed. Stir the coals and load small pieces of wood to re-ignite the fire, if desired.

Differences if chimney height and draft may lower overall burn times.

Normal Operating Sounds

Creaks and Clicks:

The 3/16" and 1/4" steel may creak or click when the stove heats up and cools down - this is normal.

Blower Sounds:

The blower will make a slight "humm" as it pushes air through the stove.

Hint:

Make sure the leveling bolts on legs are extended - preventing the hearth from amplifying any vibrations.

© Travis Industries

93508061

4050526

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Olympic Save Your Bill of Sale 2IntroductionIntroduction Important Information Table of Contents Ashes Safety PrecautionsMobile Travis Industries, Inc. grants no warranty, implied orFeatures & Specifications Preparation for Installation Planning The InstallationAdditional Accessories Needed for Installation Stove Installation ConsiderationsMinimum Clearance Singlewall Reduced Connector Stove Placement RequirementsFloor Protection Requirements ClearancesTop View Corner Installation Top View Straight InstallationPerformance Chimney RequirementsDrafting Outside Air Requirements Chimney Termination RequirementsAlcove Installation Requirements Mobile Home Requirements Not the connector manufacturers clearanceCathedral Ceiling with a Factory Built Chimney Standard Ceiling with a Factory Built ChimneyHearth Stove Positive Connection Exterior Factory Built ChimneyInterior or Exterior Masonry Chimney Hearth Stove Direct ConnectionInstallation Considerations Standard vs. Cook-Top InstallationsTop Air Chamber Extension Fireplace Requirements Fireplace SizeMasonry Fireplace Requirements Insert Placement RequirementsHearth Requirements Drafting Performance Leveling Bolt InstallationBlock-Off Plate Template Block-Off Plate InstallationInsert with Direct Connection Masonry Fireplace Insert with Positive ConnectionInsert with Face Seal Connection Operating Your Appliance Safety NoticeBefore Your First Fire Opening the DoorBypass Operation Starting a Fire Ash Removal Adjusting the Burn RateApproximate Air Control Settings Re-Loading the Stove Optional Blower OperationOvernight Burn Normal Operating SoundsHints for Burning Why Dry Wood is KeySelecting Wood Wood Cutting and StorageTroubleshooting Clean the Glass if necessary Daily Maintenance while stove is in useMaintaining Your Appliance Remove Ash if necessaryCreosote Formation and Need for Removal Monthly Maintenance while appliance is in useDoor and Glass Inspection Cleaning the Air Duct and Blower if applicable Yearly MaintenanceTouch Up Paint Firebrick and Baffle InspectionReplacing the Glass Door PartsReplacing the Door Gasket Replacing the Door HandleFirebox Parts Floor and Side Firebrick Removal & ReplacementAir Tube Removal & Replacement Baffle Removal & ReplacementYears 1 & 2 Coverage Parts & Labor Limited 7 Year WarrantyYears 3 Through 5 Coverage Parts & Labor Years 6 & 7 Coverage Parts onlyListing Label Listing InformationPedestal Optional EquipmentOutside AIR Equipment Outside Air Installation for wood stoves onlyInstall the wire clip following the directions below Rear Blower Installation Part numberOutside Air Boot Installation Part number Z e Size on Insert w trim Surround Panels see s belowFront Blower To Switch the Power Cord to the Left SideIndex

1190 specifications

Avalon Stoves has long been recognized for its commitment to quality, efficiency, and performance in the realm of home heating. Among its stellar offerings, the Avalon Stoves 1190 stands out as a testament to modern innovation and classic design. This wood-burning stove caters to both functionality and aesthetics, making it an ideal addition to any home.

One of the main features of the Avalon 1190 is its impressive heating capacity. With the ability to produce up to 70,000 BTUs, this stove is capable of heating large spaces, making it perfect for open-concept layouts or larger living areas. The stove's firebox is designed to accommodate logs up to 18 inches, allowing for longer burn times and less frequent reloading.

In addition to its heating capabilities, the Avalon 1190 incorporates advanced technologies that enhance its efficiency. One notable feature is the clean-burn technology, which significantly reduces emissions while maximizing heat output. This technology not only promotes a healthier environment but also aligns with eco-friendly practices, creating a more sustainable heating option for homeowners.

The Avalon 1190 is also equipped with a secondary combustion system, which ensures that more of the wood’s energy is utilized during the burn process. This results in hotter fires and minimal smoke production, further contributing to its efficient performance. The stove's design also includes a built-in air wash system that helps keep the glass clean, allowing for a clear view of the mesmerizing flames.

Another characteristic that sets the Avalon 1190 apart is its aesthetic appeal. With a sleek and contemporary design, the stove is available in several finishes, including classic black, cast iron, and even a stylish porcelain enamel. This versatility ensures that it can seamlessly integrate into any home décor, from rustic to modern settings.

Moreover, the Avalon 1190 comes with a reliable warranty, underscoring the manufacturer's confidence in the product’s durability. Constructed with high-quality materials, this wood stove is built to last, providing warmth and comfort for years to come.

In conclusion, the Avalon Stoves 1190 is a perfect blend of high performance, innovative technology, and elegant design. Whether it’s for heating a cozy living room or creating an inviting ambiance, the Avalon 1190 remains a top choice for discerning homeowners seeking a dependable wood-burning solution. Its efficient heating capabilities, coupled with eco-friendly features, make it a model of contemporary living that respects both comfort and the environment.
Top Page Image Contents