Avalon Stoves 1190 owner manual Outside Air Boot Installation Part number

Page 43

Optional Equipment

43

Outside Air Boot Installation (Part number 99200134)

The outside air boot routes outside air to the stove for combustion. Refer to the section "Outside Air Requirements" on page 11 for installation concerns. The directions below detail installation.

1. Install the cover plate following the directions below (use the correct cover plate).

Remove the two screws on the cover plate to remove the piece that fits over the air control rod. Then replace the piece when the cover plate is in place.

Air Control Rod

The cover plate has a clip which attaches it underneath the air control.

2.Refer to the illustration below to determine the location and size of the hole penetrating the floor. Cut the hole prior to locating the stove.

3.Attach gasket to the bottom edge of the lower air boot section (near the screen). Attach gasket on top of the flanges on the upper air boot section. Slide the two sections together with both seams facing the rear (do not attach the two sections at this time).

4.Follow the directions below for attaching the upper section of the air boot (with gasket) to the stove.

5.Slide the lower section down until it contacts the hearth. Attach the two sections together following the directions

 

 

Use a

Bottom of Stove

 

screwdriver to

 

 

 

 

pry out the

Attach the included

 

knock-out.

gasket to all four top

 

 

 

edges of the air boot.

 

 

 

 

 

Attach the air boot with

 

 

the two screws included

 

 

with the kit.

 

 

 

 

1/4" Nutdriver

 

 

Use the included screws to attach

 

 

the two telescoping portions of air

 

 

boot together. The included drill bit

 

5-1/8”

should be used to drill the hole.

 

 

8-7/8”

 

Make sure the air boot is expanded

 

to the correct size before drilling.

Attach gasket to the bottom

 

 

 

 

edge of the air boot.

 

 

 

 

 

9/64” Drill Bit

5/16" Nutdriver

 

 

The hole in the floor (and hearth)

 

 

must be a minimum 16 square

 

 

inches. It should be 1/2” smaller

 

 

than the footprint of the air boot in

Floor (and hearth)

 

each dimension to allow for the

 

 

gasket to seal.

© Travis Industries

93508061

4050526

Image 43
Contents Olympic Introduction Important Information 2IntroductionSave Your Bill of Sale Table of Contents Ashes Safety PrecautionsMobile Travis Industries, Inc. grants no warranty, implied orFeatures & Specifications Stove Installation Considerations Planning The InstallationPreparation for Installation Additional Accessories Needed for InstallationClearances Stove Placement RequirementsMinimum Clearance Singlewall Reduced Connector Floor Protection RequirementsTop View Corner Installation Top View Straight InstallationDrafting Chimney RequirementsPerformance Outside Air Requirements Chimney Termination RequirementsAlcove Installation Requirements Mobile Home Requirements Not the connector manufacturers clearanceCathedral Ceiling with a Factory Built Chimney Standard Ceiling with a Factory Built ChimneyHearth Stove Positive Connection Exterior Factory Built ChimneyInterior or Exterior Masonry Chimney Hearth Stove Direct ConnectionInstallation Considerations Standard vs. Cook-Top InstallationsTop Air Chamber Extension Fireplace Requirements Fireplace SizeHearth Requirements Insert Placement RequirementsMasonry Fireplace Requirements Drafting Performance Leveling Bolt InstallationBlock-Off Plate Template Block-Off Plate InstallationInsert with Direct Connection Masonry Fireplace Insert with Positive ConnectionInsert with Face Seal Connection Opening the Door Safety NoticeOperating Your Appliance Before Your First FireBypass Operation Starting a Fire Approximate Air Control Settings Adjusting the Burn RateAsh Removal Normal Operating Sounds Optional Blower OperationRe-Loading the Stove Overnight BurnWood Cutting and Storage Why Dry Wood is KeyHints for Burning Selecting WoodTroubleshooting Remove Ash if necessary Daily Maintenance while stove is in useClean the Glass if necessary Maintaining Your ApplianceDoor and Glass Inspection Monthly Maintenance while appliance is in useCreosote Formation and Need for Removal Firebrick and Baffle Inspection Yearly MaintenanceCleaning the Air Duct and Blower if applicable Touch Up PaintReplacing the Door Handle Door PartsReplacing the Glass Replacing the Door GasketFirebox Parts Floor and Side Firebrick Removal & ReplacementAir Tube Removal & Replacement Baffle Removal & ReplacementYears 6 & 7 Coverage Parts only Limited 7 Year WarrantyYears 1 & 2 Coverage Parts & Labor Years 3 Through 5 Coverage Parts & LaborListing Label Listing InformationPedestal Optional EquipmentOutside AIR Equipment Outside Air Installation for wood stoves onlyInstall the wire clip following the directions below Rear Blower Installation Part numberOutside Air Boot Installation Part number Z e Size on Insert w trim Surround Panels see s belowFront Blower To Switch the Power Cord to the Left SideIndex

1190 specifications

Avalon Stoves has long been recognized for its commitment to quality, efficiency, and performance in the realm of home heating. Among its stellar offerings, the Avalon Stoves 1190 stands out as a testament to modern innovation and classic design. This wood-burning stove caters to both functionality and aesthetics, making it an ideal addition to any home.

One of the main features of the Avalon 1190 is its impressive heating capacity. With the ability to produce up to 70,000 BTUs, this stove is capable of heating large spaces, making it perfect for open-concept layouts or larger living areas. The stove's firebox is designed to accommodate logs up to 18 inches, allowing for longer burn times and less frequent reloading.

In addition to its heating capabilities, the Avalon 1190 incorporates advanced technologies that enhance its efficiency. One notable feature is the clean-burn technology, which significantly reduces emissions while maximizing heat output. This technology not only promotes a healthier environment but also aligns with eco-friendly practices, creating a more sustainable heating option for homeowners.

The Avalon 1190 is also equipped with a secondary combustion system, which ensures that more of the wood’s energy is utilized during the burn process. This results in hotter fires and minimal smoke production, further contributing to its efficient performance. The stove's design also includes a built-in air wash system that helps keep the glass clean, allowing for a clear view of the mesmerizing flames.

Another characteristic that sets the Avalon 1190 apart is its aesthetic appeal. With a sleek and contemporary design, the stove is available in several finishes, including classic black, cast iron, and even a stylish porcelain enamel. This versatility ensures that it can seamlessly integrate into any home décor, from rustic to modern settings.

Moreover, the Avalon 1190 comes with a reliable warranty, underscoring the manufacturer's confidence in the product’s durability. Constructed with high-quality materials, this wood stove is built to last, providing warmth and comfort for years to come.

In conclusion, the Avalon Stoves 1190 is a perfect blend of high performance, innovative technology, and elegant design. Whether it’s for heating a cozy living room or creating an inviting ambiance, the Avalon 1190 remains a top choice for discerning homeowners seeking a dependable wood-burning solution. Its efficient heating capabilities, coupled with eco-friendly features, make it a model of contemporary living that respects both comfort and the environment.