Moxa Technologies AWK-1200-AP Fragmentation Threshold, RTS Threshold, Beacon Period, WDS Enable

Page 26

MOXA AirWorks AWK-1200-AP User’s Manual

Web Console Configuration

Fragmentation Threshold

This setting should remain at its default value of 2346. Setting the Fragmentation value too low may result in poor performance.

RTS Threshold

This setting should remain at its default value of 2346. If you encounter inconsistent data flow, only minor modifications to the value are recommended.

Beacon Period

Beacons are packets sent by a wireless Access Point to synchronize wireless devices. Specify a Beacon Period value of between 20 and 1000. The default value is set to 100 milliseconds.

DTIM Interval

A DTIM is a countdown informing clients of the next window for listening to broadcast and multicast messages. When the wireless Access Point has buffered broadcast or multicast messages for associated clients, it sends the next DTIM with a DTIM Interval value. Wireless clients detect the beacons and awaken to receive the broadcast and multicast messages. The default value is 1. Valid settings are between 1 and 255.

802.11d Enable

Enables 802.11d operation. 802.11d is a wireless specification for operation in additional regulatory domains. This supplement to the 802.11 specifications defines the physical layer requirements (channelization, hopping patterns, new values for current MIB attributes, and other requirements to extend the operation of 802.11 WLANs to new regulatory domains, or countries). The current 802.11 standard defines operation in only a few regulatory domains (countries). This supplement adds the requirements and definitions necessary to allow 802.11 WLAN equipment to operate in markets not served by the current standard. Enable this option if you are operating in one of these “additional regulatory domains.”

Transmit Power

Normally, the wireless transmitter operates at 100% power. In some circumstances, however, there might be a need to isolate specific frequencies to a smaller area. By reducing the power of the radio, you can prevent transmissions from reaching beyond your corporate/home office or designated wireless area.

WDS Enable

When WDS is enabled, this access point functions as a wireless repeater and is able to wirelessly communicate with other APs via WDS links. Note that WDS is incompatible with WPA -- both features cannot be used at the same time. A WDS link is bidirectional; so this AP must know the MAC Address (creates the WDS link) of the other AP, and the other AP must have a WDS link back to this AP. Make sure the APs are configured with same channel number.

WDS AP MAC Address

Specifies one-half of the WDS link. The other AP must also have the MAC address of this AP to create the WDS link back to this AP.

3-7

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Moxa AirWorks AWK-1200-AP User’s Manual First Edition, JulyDisclaimer Copyright NoticeTrademarks Table of Contents Appendix C Regulatory Compliance Information Introduction Overview Package ChecklistProduct Features System RequirementsInline Power Injector PoE Getting Started Locating the Data Input and PoE Ports First Time Installation and ConfigurationInterface on the Inline Power Injector Interface on the AWK-1200-AP UnitDevice Figures Mounting the AWK-1200-AP on a Wall or MastWhat to Check before You Install the AWK-1200-AP StepWeb Configuration Basic ConfigurationBasic Configuration Steps Web Access ProceduresWeb Configuration Structure LAN Settings HelpConfiguring the Wireless Ssid Wireless Network Name also called the SsidConfiguring Wireless Encryption Changing the Supervisor Account & Password Upgrading the Firmware Updating the FirmwareMoxa AirWorks AWK-1200-AP User’s Manual Getting Started Web Console Configuration Wireless BasicWPA-Personal and WPA-Enterprise Super G ModeMode WPA-Personal WPA-EnterpriseMAC Address Filter Enable MAC Address FilterAdvanced Add/Edit MAC Address Filter SettingsAdvance Wireless MAC Address ListWDS Enable 802.11d EnableTransmit Power Fragmentation ThresholdAdmin ToolsTime Restore Configuration from FileSave Configuration To Wireless Network Setup Wizard SystemFirmware Reboot the DeviceRestore all Settings to the Factory Defaults Device Info Firmware UpgradeStatus Firmware InformationMAC Address SignalLAN Computers RateWhat to View Apply Log Settings NowLogs View LevelsStatistics Errors Specifications WlanRegulatory Approvals Default Settings BasicDhcp Advanced Wireless MAC Address FilterFirmware Federal Communications Commission FCC Requirements, Part Regulatory Compliance Information15.21 Prohibition of co-location Regulatory information / Disclaimers MPE Statement Safety InformationSafety Information
Top Page Image Contents