Casablanca Fan Company 55012, 55010, 55011 operation manual Switch Housing

Page 14

Switch Housing

www.CasablancaFanCo.com

1.888.227.2178

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Screw two (2) housing assembly screws

Feed the wire plug through the center

 

 

Insert the third screw, found in

 

from the

 

hardware bag halfway into

hole of the upper switch housing, then

 

the

 

hardware bag, into place and then

 

the motor housing. It does not matter

wrap keyhole slots around the screws and

 

 

 

tighten all three (3) screws.

 

which two screw holes you choose.

twist counterclockwise.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Make sure the upper switch housing is securely

 

 

 

 

 

 

 

 

 

 

 

 

 

 

attached to the mounting plate. Failure to properly

 

 

 

 

 

 

 

 

 

 

 

 

 

 

secure all 3 assembly screws could result in the switch

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

housing fixture falling.

 

 

 

 

 

 

 

14

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

M6007-01 • 06/14/12 • © Casablanca Fan Company

Image 14
Contents Table of Contents What to Expect with Your Installation Ladder Pliers Screwdrivers 11/32 Wrench Power Drill Drill Bit OptionalTools Needed Fan from a vaulted or angled ceiling See previous Mounting OptionsStandard Ceiling Mounting Outlet Box Style Required Remove all four 4 mounting Isolators Ceiling Bracket InstallationMounting Isolator For angled ceilings, point Opening toward peak Ceiling Bracket Installation Preparation Remove the shipping blocks fromDownrod Setscrew so that the downrod Remove the pre-installed Hand tighten the downrod atTighten the setscrew Leave at least 8 extendingPut the wires and downrod through FanWiring Using an orange wire Connector from Hardware bagCanopy HolesBlades Blades sold separatelySwitch Housing Which two screw holes you choose Twist counterclockwiseComing from the switch housing Colored markings on the connectorsMaintenance & Cleaning To switch the direction of air flowTroubleshooting Fan doesn’t work