Hoover Self-Propelled Powered Hand Tool Lubrication, Edge groomer replacement, Thermal protector

Page 12

3-22

 

C

E

6.With curved ends down, slide end plates (C) of brush roll into slots (E) on tool.

3-23

B

7.Replace belt guard (B) making sure not to pinch brush bristles in guard. Turn agitator, making sure it rotates freely.

Replace and tighten screws.

3-24

A

8.To replace bottom plate (A), insert the four tabs on edge of bottom plate into slots on front of tool.

Pivot bottom plate down and snap closed.

Powered hand tool

Belt replacement

The powered hand tool belt is designed to last a long time and is not normally replaced. However, if the belt is crack- ed, gouged or broken, it should be

replaced.

3-25

The belt can be seen through the top of the nozzle or by removing the bottom plate and belt guard (Figs. 3-19 and 3-20.

Replacing belt

When replacing belt, ask for HOOVER

part No. 38528037.

1.Remove bottom plate, belt guard and brush roll as described in Figs. 3-19 through 3-21.

3-26

F

 

E

2.Grasp turbine (E) and pull firmly to remove.

3.Remove belt from turbine pulley (F). Replace with new belt.

3-27

H

G

4.With flat sides of turbine retainers (G) pointing down, slide retainers into grooves (H) in tool housing and snap into place.

5.Replace brush roll, belt guard, and bottom plate as described in Figs. 3-21 through 3-24.

Edge groomer replacement

When to replace

The edge groomers, located on both sides of the front of the cleaner, should be replaced when they appear worn.

What to buy

When purchasing edge groomers, ask

for HOOVER part No. 39511004.

3-28

12

Replacing edge groomers

Disconnect cleaner from electrical outlet.

Warning - Brush roll can start sud- denly. Unplug cleaner when it is turned over.

Remove bottom plate as described in Fig. 3-9.

Lift off both old edge groomers and slide new edge groomers into position as shown.

Reposition bottom plate and secure with 4 Phillips head screws (Fig. 3-13).

Lubrication

The motor is equipped with bearings that contain sufficient lubrication for the life of the motor. The addition of lubricant could cause damage. Therefore, do not add lubricant to motor bearings. The agitator is equipped with two ball bearings that should be lubricated peri- odically by a Hoover Factory Service Center or an Authorized Hoover Warranty Service Dealer (Depot).

Thermal protector

An internal thermal protector has been designed into your cleaner to protect it from overheating.

When the thermal protector activates, the cleaner will stop running. If this happens, proceed as follows:

1.Turn the cleaner OFF and discon- nect it from the electrical outlet.

2.Check secondary and final filters for dirt accumulation.

3.Refer to “Clearing blockages” sec-

tion.

4.When cleaner is unplugged and the motor cools for 30 minutes, the thermal protector automatically resets and cleaning may continue.

If the thermal protector continues to activate after following the above steps, your cleaner may need servicing (see “Service” section).

Page 11 Page 13
Image 12
Page 11 Page 13
Contents This product was designed for easy Assembly See Review this manual before Operating cleaner Fill in and retainEnglish pp.1-14 Carton contents IndexStep I Attach handle OperationsCleaner description ON-OFF SwitchSelf-propel feature Transporting cleanerCarrying cleaner Carpet height adjustmentHandle positions Brush roll controlCleaning tools Maintenance Headlight replacement Secondary and final filtersBelt replacement Brush roll replacementReplacing flat belt Powered hand tool Agitator brush roll replacementReplacing brush roll Edge groomer replacement LubricationThermal protector Service Hoover Cleaning PerformanceTrouble shooting Clearing blockagesFull Two Year Warranty If blockage occurs during powered hand tool useDomestic Use Checking under bottom plateManual del usuario Anote y guardeLea este manual antes de Usar la aspiradora Español págIndice Cómo ensamblar la aspiradoraCómo usar Contenido de la caja5Para transportar 2Interruptor de encender-apagar3Mecanismo de autopropulsión 4Para trasladarMantenimiento Filtros secundario y final Reemplazo del foco delanteroReemplazo de las correas Reemplazo del rodillo de escobillas Accesorio de mano turboaccionadoReemplazo del limpiaorillas LubricaciónServicio Rendimiento deLocalizacion de averias Desatascamiento de obstrucciones1Inspección del paso de aire 2Comprobación debajo de la place inferiorGarantía completa por dos años Uso domésticoPage Manuel de lutilisateur Remplir et à conserverLire ce manuel avant dutiliser laspirateur Mode d’emploi Assemblage de l’aspirateur1Description de l’aspirateur Contenu de la caisse4Déplacement de l’aspirateur 9Commande d’ agitateur2Commutateur ON- OFF marche-arrêt 3Fonction d’auto- propulsionEntretien Remplacement de la courroie 5Remplacement du filtre finalRemplacement du phare Le filtre secondaire et le filtre finalRemplacement de l’agitateur Accessoire portatif à turbineDépannage Garantie de deux ans Débouchages1Inspection du passage de l’air 2Vérification sous la Plaque inférieure

Self-Propelled Powered Hand Tool specifications

The Hoover Self-Propelled Powered Hand Tool represents a major advancement in cleaning technology, designed to make home maintenance easier and more efficient. This innovative tool effectively merges user-friendly features with robust functionality, making it a must-have for both everyday cleaning tasks and more challenging jobs.

One of the standout characteristics of the Hoover Self-Propelled tool is its self-propelling technology. This unique feature allows the tool to move forward with minimal effort from the user. By harnessing the power of motorized assistance, cleaning becomes less physically taxing. Whether tackling carpets or hard floors, users can enjoy reduced fatigue and improved maneuverability, making cleaning a quicker, less strenuous process.

In addition to its self-propelling capability, the Hoover tool is equipped with a range of specialized cleaning modes. These modes can be easily switched depending on the surface type, allowing for optimal dirt removal across various flooring materials. For instance, the brush roll can automatically adjust its height to meet the specific demands of carpeted areas, while a gentle suction setting can be utilized for delicate surfaces such as upholstery or curtains.

The Hoover Self-Propelled Hand Tool also boasts advanced filtration technologies, crucial for maintaining a healthy living environment. With a high-efficiency particulate air (HEPA) filter, this tool captures fine particles and allergens, ensuring that the air remains clean as you clean your home. This feature is particularly beneficial for allergy sufferers, who can breathe easier knowing that indoor air quality is significantly improved.

Durability is another important characteristic of the Hoover Self-Propelled tool. Constructed from high-quality materials, it is designed to withstand regular use while still maintaining peak performance. Its ergonomic design not only enhances usability but also ensures comfort during extended cleaning sessions.

Additionally, the tool comes with a variety of attachments, further enhancing its versatility. From specialized brush heads for pet hair removal to crevice tools for tight spaces, these attachments broaden the cleaning capabilities of the Hoover tool, making it suitable for a wide range of applications beyond mere floor cleaning.

In summary, the Hoover Self-Propelled Powered Hand Tool embodies a perfect blend of innovative technology, user-centric design, and superior cleaning efficiency. Its self-propelling feature, adaptable cleaning modes, advanced filtration system, and robust construction make it an essential tool for maintaining a spotless home with minimal effort.
Top Page Image Contents