Hoover C1660-900 user manual Thermal protector, Service

Page 11

Thermal protector

An internal thermal protector has been designed into your cleaner to protect it from overheating.

When the thermal protector activates, the cleaner will stop running. If this happens, proceed as follows:

1.Turn the cleaner OFF and discon- nect it from the electrical outlet.

2.Check filters for dirt accumulation.

3.Refer to “Clearing blockages” section.

4.When cleaner is unplugged and the motor cools for 30 minutes, the thermal protector automatically resets and cleaning may continue.

If the thermal protector continues to activate after following the above steps, your cleaner may need servicing (see“Service” section).

Service

To obtain approved HOOVER service and genuine HOOVER parts, locate the nearest Authorized Factory Service

Center or Authorized Hoover Warranty Service Dealer (Depot) by:

checking the Yellow Pages under “Vacuum Cleaners - Household” OR -

checking the list of Factory Service Centers provided with this cleaner OR -

calling 1-800-944-9200for an automated referral of authorized service outlet locations (U.S. only).

Do not send your cleaner to The Hoover Company in North Canton for service, this will only result in delay.

If further assistance is needed, contact The Hoover Company Consumer Response Center, North Canton,

Ohio 44720, Phone: 330-499-9499.

In Canada, contact Hoover Canada, Burlington, Ontario L7R 4A8, Phone: 1-800-263-6376.

Always identify your cleaner by the com- plete model number when requesting information or ordering parts. (The model number appears on the bottom of the cleaner.)

4.If you have a problem

4.If you have a problem

If a minor problem occurs, it usually can be solved quite easily when the cause is found by using the check list.

Problem: Cleaner won’t run

Possible cause

Possible solution

Not firmly plugged into wall and/or extension cord

Plug unit in firmly

No voltage in wall plug

Check fuse or breaker

Blown fuse or tripped breaker

Replace fuse or reset breaker

Thermal protector activated

Allow cleaner to cool for 30 minutes (this will reset the thermal protector) (see pg. 11). Prob

Problem: Cleaner won’t pick up Possible cause

Possible solution

Broken or worn belt

Replace belt

•Agitator brush roll worn

Replace brush roll

Dirt cup full

Empty cup

Incorrect carpet height setting

Move nozzle control knob to lower setting

Blockage in air flow passage

Clear blockage

HEPA filter clogged

Clean HEPA filter as described in the “Filter assembly” section

Dirt cup not properly installed

Position dirt cup properly (Fig. 3-4)

Dirt cup lid not positioned properly or missing

Ensure that dirt cup lid is properly positioned

Filter assembly not installed properly

Ensure that the filter assembly is posi- tioned properly (Fig. 3-10)

Problem: Cleaner hard to push Possible cause

Possible solution

Incorrect carpet height setting

Move nozzle control knob to a higher setting

Problem: Cleaning tools won’t pick up

Possible cause

Possible solution

Dirt cup not properly installed

Position dirt cup properly (Fig. 3-4)

Blockage in hose

Clear blockage

Power Boost in “neutral” position

Move Power Boost switch to lock posi- tion.

Problem: Cleaner is not quieter when switched to HUSH mode

Possible cause

Possible solution

Power Boost switch in lock position

Push Power Boost switch forward to “neutral” position.

Problem: Smoky/burning smell detected

Possible cause

Possible solution

Belt broken or stretched

Replace agitator brush roll belt as described in Figs. 3-16 through 3-26 in the Maintenance section.

Continued

11

 

Image 11
Contents User’s Manual ContentsPacked inside extension wand Grounding instructionsExtension cord instructions How to use Hose connection ON-OFF-HUSH switchPower Boost Switch Transporting cleanerCarpet height AdjustmentCleaning lightweight flexible rugs Stair cleaningAttach wand and tools How to clean toolsRemove hose Replacing hoseHow to clean filter assembly Filter assemblyWhen to empty How to emptyWhat to buy Headlight replacementCleaning final filter Disconnect cleaner from electrical outlet Belt replacementWhen to replace How to replaceHoover part no Disconnect cleaner from electrical outletLubrication Thermal protector ServiceCheck airflow path Turn cleaner OFF and disconnect from electrical outletClearing blockages Check dirt ductGracias por haber elegido un producto Hoover Contenido¡Guarde estas instrucciones Lea este manual antes de hacer funcionar la aspiradoraCómo usar la limpiadora Para comenzarInterruptor de ampliación de potencia PosicionesConexión para la manguera Interruptor de encender/apagar/ Hush silencioMantenimiento Reemplazo de la luz delantera Conjunto del filtroCómo limpiar el conjunto del filtro Limpieza del filtro finalProtector térmico El rodillo de escobillas del agitador Cuándo reemplazarloCómo reemplazarlo LubricaciónRevise el flujo de aire Si tiene un problemaEliminación de obstrucciones Revise el conducto para el polvoMerci d’avoir choisi un produit Hoover ContenuLire ces instructions Avant d’utiliser ’appareil Avec le manche en position de rangement Contenu de l’emballageInstructions de mise à la terre Instructions pour la rallongeInterrupteur de surpuissance Accessoires de nettoyageConnexion du tuyau Interrupteur Marche/ArrêtPour enlever le tuyau Choix de l’accessoire appropriéInstallation de la rallonge et des accessoires de nettoyage Nettoyage des accessoiresNettoyage du filtre terminal Remplacement de l’ampouleRemplacement de la courroie Comment nettoyer l’ensemble du filtre ?Quand le remplacer ? Le rouleau-brosse agitateur’interrupteur de surpuissance est La position verrouillé Déblocage des obstructionsPage Hoover y Son marcas registradas Hoover et

C1660-900 specifications

The Hoover C1660-900 is a commercial-grade vacuum cleaner designed specifically for efficiency, durability, and ease of use in various cleaning environments. Known for its lightweight design and strong suction capabilities, this machine is ideal for businesses, schools, and other large spaces that require regular cleaning.

One of the standout features of the C1660-900 is its powerful 12-amp motor, which delivers exceptional suction performance. This robust motor enables the vacuum to pick up a wide range of debris, from fine dust to larger particles, ensuring that surfaces remain clean and hygienic. The machine operates with a high-efficiency filtration system. This filtration system captures dust and allergens, contributing to improved air quality in the environment it cleans.

The C1660-900 is designed with user comfort in mind. Weighing just over 8 pounds, this vacuum is easy to maneuver and can be used for extended periods without causing fatigue. The lightweight nature of the machine allows users to transport it effortlessly from one location to another, making it an ideal choice for commercial use.

Another key characteristic of the Hoover C1660-900 is its versatility. It comes equipped with a 40-foot power cord, providing an extended reach that minimizes the need for frequent outlet changes while cleaning. Additionally, the vacuum features a self-propelled design, which allows for smooth operation and reduces the effort needed to push or pull the machine during use.

The vacuum is also designed with practicality in mind. Its low-profile design allows it to easily clean underneath furniture and tight spaces, helping users achieve an optimal clean in traditionally hard-to-reach areas. The durable construction of the C1660-900 ensures that it can withstand the rigors of daily use, making it a reliable investment for any commercial cleaning operation.

Overall, the Hoover C1660-900 combines powerful suction, user-friendly design, and advanced filtration technology. These features make it a top contender for those seeking an effective cleaning tool that can handle the demands of commercial spaces while providing ease of use and reliable performance.