Hoover C1660-900 Hose connection, ON-OFF-HUSH switch, Power Boost Switch, Handle positions

Page 4

2-2

A

Hose connection

Hose must be attached to cleaner base for floor cleaning.

To attach hose, use the end of the hose to push the cover (A) down and push hose onto opening.

Twist hose end slightly to tighten the con- nector.

2-3

B

ON-OFF-HUSH™ switch

Plug cord into electrical outlet.

To turn cleaner ON, push switch (B) up.

To turn cleaner OFF, push switch to middle position.

For quieter vacuuming, push switch down (HUSH) position.

Put Power Boost Switch in neutral when using ON or HUSH setting.

2-4

C

Power Boost Switch

Use the Power Boost Switch (C) to add extra cleaning power for cleaning heavily soiled areas and for picking up dry debris spills.

Push the switch forward for a temporary boost. When released, the boost will auto- matically go to the “neutral” position.

Push the switch back to lock it in the Boost position. To unlock, push the switch for- ward to the “neutral” position.

Use the lock position for larger areas or when using the cleaning tools.

The Boost can be used with either the ON or HUSH mode selected (see Fig. 2-3).

Put Power Boost Switch in neutral when using ON or HUSH setting.

2-5

2-6

2-7

Handle positions

The handle of your cleaner has three posi- tions; upright when using cleaning tools; operating position for general operation on carpet and floors; low for reaching under low furniture. Step on handle release pedal to lower handle.

Transporting cleaner

Put handle in upright position. Tilt cleaner back on rear wheels. Push forward.

Carrying handle

Use the carrying handle to lift the cleaner.

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents
Contents User’s ManualExtension cord instructions Grounding instructionsPacked inside extension wand How to use ON-OFF-HUSH switch Power Boost SwitchTransporting cleaner Hose connectionAdjustment Cleaning lightweight flexible rugsStair cleaning Carpet heightHow to clean tools Remove hoseReplacing hose Attach wand and toolsFilter assembly When to emptyHow to empty How to clean filter assemblyCleaning final filter Headlight replacementWhat to buy Belt replacement When to replaceHow to replace Disconnect cleaner from electrical outletLubrication Disconnect cleaner from electrical outletHoover part no Service Thermal protectorTurn cleaner OFF and disconnect from electrical outlet Clearing blockagesCheck dirt duct Check airflow pathContenido ¡Guarde estas instruccionesLea este manual antes de hacer funcionar la aspiradora Gracias por haber elegido un producto HooverPara comenzar Cómo usar la limpiadoraPosiciones Conexión para la mangueraInterruptor de encender/apagar/ Hush silencio Interruptor de ampliación de potenciaMantenimiento Conjunto del filtro Cómo limpiar el conjunto del filtroLimpieza del filtro final Reemplazo de la luz delanteraEl rodillo de escobillas del agitador Cuándo reemplazarlo Cómo reemplazarloLubricación Protector térmicoSi tiene un problema Eliminación de obstruccionesRevise el conducto para el polvo Revise el flujo de aireLire ces instructions Avant d’utiliser ’appareil ContenuMerci d’avoir choisi un produit Hoover Contenu de l’emballage Instructions de mise à la terreInstructions pour la rallonge Avec le manche en position de rangementAccessoires de nettoyage Connexion du tuyauInterrupteur Marche/Arrêt Interrupteur de surpuissanceChoix de l’accessoire approprié Installation de la rallonge et des accessoires de nettoyageNettoyage des accessoires Pour enlever le tuyauRemplacement de l’ampoule Remplacement de la courroieComment nettoyer l’ensemble du filtre ? Nettoyage du filtre terminalLe rouleau-brosse agitateur Quand le remplacer ?Déblocage des obstructions ’interrupteur de surpuissance est La position verrouilléPage Hoover y Son marcas registradas Hoover et