Hoover UH70600 manual Service, Hoover Cleaning Performance, Lubrication, Trouble shooting

Edge groomer replacement

When to replace

The edge groomers, located on both sides of the front of the cleaner, should be replaced when they appear worn.

What to buy

When purchasing edge groomers, ask

for HOOVER part No. 39511004.

3-28

Replacing edge groomers

Disconnect cleaner from electrical outlet.

Warning - Brush roll can start sud- denly. Unplug cleaner when it is turned over.

Remove bottom plate as described in Fig. 3-9.

Lift off both old edge groomers and slide new edge groomers into position as shown.

Reposition bottom plate and secure with 4 Phillips head screws (Fig. 3-14).

Thermal protector

An internal thermal protector has been designed into your cleaner to protect it from overheating.

When the thermal protector activates, the cleaner will stop running. If this happens, proceed as follows:

1.Turn the cleaner OFF and discon- nect it from the electrical outlet.

2.Check secondary and final filters for dirt accumulation.

3.Refer to “Clearing blockages” sec-

tion.

4.When cleaner is unplugged and the motor cools for 30 minutes, the thermal protector automatically resets and cleaning may continue.

If the thermal protector continues to acti- vate after following the above steps, your cleaner may need servicing (see “Service” section).

Lubrication

The motor is equipped with bearings that contain sufficient lubrication for the life of the motor. The addition of lubricant could cause damage. Therefore, do not add lubricant to motor bearings. The agitator is equipped with two ball bearings that should be lubricated peri- odically by a Hoover Factory Service Center or an Authorized Hoover Warranty Service Dealer (Depot).

Service

To obtain approved HOOVER service and genuine HOOVER parts, locate the nearest Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer (Depot) by:

•checking the Yellow Pages under “Vacuum Cleaners - Household” OR-

•checking the list of Factory Service Centers provided with this cleaner OR -

•Visit us online at www.hoover.com to find the service outlet nearest you (click on the “Service” button)

OR -

•calling 1-800-944-9200for an automated referral of authorized

service outlet locations (U.S. only). Do not send your cleaner to The Hoover Company in North Canton for service, this will only result in delay.

If further assistance is needed, contact The Hoover Company Consumer Response Center, North Canton, Ohio 44720 Phone: 330-499-9499.

In Canada, contact Hoover Canada, Burlington, Ontario L7R 4A8, Phone: 1-800-263-6376.

Always identify your cleaner by the complete model number when request- ing information or ordering parts. (The model number appears on the back of the handle.)

Hoover Cleaning Performance

This Hoover Cleaning Performance System is for comparing the relative pro- gressive performance of Hoover uprights only and not for comparison with any other brands. The majority of this rating is based upon the ASTM International Carpet Cleaning Effective- ness Testing (ASTM Test F608). Other performance factors include Hose Power (ASTM Test F558), Surface Litter Cleaning, Hard Floor Cleaning, Edge Cleaning, cleaning Width and Air Filtration.

4. Trouble shooting

If a minor problem occurs, it usually can be solved quite easily when the cause is found by using the checklist below.

Problem: Cleaner won’t run

Possible Cause

Possible Solution

•Not firmly plugged in

•Plug unit in firmly

•No voltage in wall plug

•Check fuse or breaker

•Blown fuse or tripped breaker

•Replace fuse or reset breaker

•Thermal protector activated

•Allow cleaner to cool for 30 minutes (this will reset the thermal protector)

Problem: Cleaner / tools won’t pick up

Possible Cause

Possible Solution

•Broken or worn belt(s)

•Replace belt(s)

•Brush roll worn

•Replace brush roll

•Filter bag full

•Change filter bag

•Incorrect carpet height setting

•Move carpet height control to lower setting

•Blockage in air flow passage

•Clear blockage (see “Clearing block- ages section)

Problem: Cleaner hard to push

Possible Cause

Possible Solution

•Incorrect carpet height setting

•Move carpet height control to a higher setting

Problem: Cleaner won’t self-propel

Possible Cause

Possible Solution

•Flat belt broken or worn

•Replace belt

•Self-propel button in OFF position

•Slide button to ON

Problem: Brush roll not turning

Possible Cause

Possible Solution

•Brush roll in OFF position

•Move brush roll control to ON position (carpet)

•Flat belt broken or worn

•Replace belt

Continued 13