Bosch Appliances GWH 2700 ES LP, ESVVT, GWH 2700 ES NG manual For your safety

Page 3

Warning

1Warning

For your safety

Do not store or use gasoline or other flammable, combustible or corrosive vapors and liquids in the vicinity of this or any other appliance.

Warning: Carefully plan where you install the heater. Correct combustion air supply and flue pipe installation are very important. If a gas appliance is not installed correctly, fatal accidents can result, such as carbon monoxide poisoning or fire.

Warning: Exhaust gas must be vented to outside using stainless steel vent material suitable for category III vent systems and temperatures up to 480°F. Vent piping must be sealed gas-tight to prevent possibility of flue gas spillage, carbon monoxide emissions and risk of fire, resulting in severe personal injury or death. Approved vent terminators must be used when penetrating to the outside.

Warning: Place the heater in a location where water leaks will do NO DAMAGE to adjacent areas or lower floors.

Warning: Field wiring connections and electrical grounding must comply with local codes, or in the absence of local codes, with the latest edition of the National Electric Code, ANSI/NFPA 70, or in Canada, all electrical wiring must comply with the local codes and the Canadian Electrical Code, CSA C22.1 Part 1.

Warning: Shock hazard: line voltage is present. Before servicing the water heater, unplug power supply cord from outlet. Failure to do so could result in severe personal injury or death.

Warning: The heater must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures equal to or more than 0.5 psig.

Warning: The appliance should be located in an area where leakage of the heater or connections will not result in damage to the area adjacent to the appliance or to lower floors of the structure. When such locations cannot be avoided, it is recommended that a suitable drain pan, adequately drained, be installed under the appliance. The pan must not restrict combustion air flow.

Warning: The maximum inlet gas pressure must not exceed the value specified by the manufacturer and that the minimum value listed is for the purposes of input adjustment.

Warning: If a water heater is installed in a closed water supply system, such as one having a backflow preventer in the cold water supply line, means shall be provided to control thermal expansion. Contact the water supplier or local plumbing inspector on how to control this situation.

Warning: Keeping appliance area clear and free from combustible materials, gasoline and other flammable vapors and liquids.

Warning: Do not obstruct the flow of combustion and ventilation air.

Warning: Precautions must be taken prior to manually operating the relief valve to avoid contact with hot water coming out of the relief valve and to prevent water damage.

Caution: Label all wires prior to disconnection when servicing controls. Wiring errors can use improper and dangerous operation.

Verify proper operation after servicing.

Warning: In order for the freeze prevention kit to provide adequate protection,120V AC must always be supplied to the water heater.

6 720 608 542

3

Image 3
Contents What to do if you smell gas Intended for variable flow applicationsIndex For your safety Appliance details FeaturesSpecifications Technical data To remove combustion cover service only Unpacking the heaterGWH 2700 ES is not approved or designed for Venting General rules to follow for safe operationDimensions Dimensions and Minimum installation clearancesVenting Installation instructionsTools required for installation IntroductionInstallation instructions Horizontal venting systems only Venting SpecificationsFittings or Piping Equivalent Feet Maximum combustion air and exhaust pipe length Installation instructions Condensate drain requirementsTwin pipe termination clearances Minimum combustion air and exhaust pipe lengthCanadian installations1 Installations2 Canadian installations1 Horizontal twin pipe penetration Vent connections Vertical venting installation twin pipe penetra- tionVenting Flex ProTech Heat Fab Installation instructions Condensate drain installationExample Total equivalent vent length calculationExhaust IntakeAdjusting minimum power fan speed P2 Adjusting maximum power fan speed P1Level Vent length1 Speed P2 Installation instructions Twin pipe and Concentric pipe Combustion air requirementsProper location for installing your heater Heater placement and clearancesMounting installation Gas piping & connections GAS Line Sizing For Natural GAS Water quality Water connectionsGWH Domestic hot water recirculationOperating Pressure Test Connecting manometerMeasuring gas pressure Static Pressure TestElectrical power supply Electrical connectionsPosition of the fuses in control unit LCD Display functions Operation instructionsFor your safety read before operating your water heater PowerTemperature selection Program button Use of optional remote control Accessory part no. TSTAT2Reset button OperationWinterizing for seasonal use Maintenance and serviceAnnual maintenance table Every year Annual maintenanceAdjusting CO2 carbon dioxide Descaling using a pumpMineral scale build-up Once Gas Pressure is adequate Measuring CO2 combustion cover must be installedAdjusting CO2 Returning to Service% 3.0 % 60 ppm Final ReadingsProgram Description Factory Default Program valuesComment Diagnostic menu Control board diagnosticsWater is not hot enough TroubleshootingTroubleshooting Water is too hotHot water temperature fluctuates at tap Low water flow/pressureNoisy burner/heater during operation Lack of adequate gas pressure. Inadequate gas Error code diagnostics Problem solvingVenting may cause this failure Problem solving Display Cause SolutionOver-temperature detected by No flame ionization detected with Electrical diagram Electrical diagramSensor resistance charts Back Flow characteristics Functional scheme GWH 2700 ES Functional schemeInterior components diagram and parts list Interior components diagram and parts listInterior components Appliance overview Components diagram GroupDescription Reference Interior components diagram and parts list Group 1211 6720608158-73.1AL Interior components diagram and parts list Group 708 300 Components Protecting the environmentProtecting the environment PackingLimited Warranty Limited Warranty 6720608542