Bradford-White Corp EFR-1-60T1206EN, EFR160T120 How to reset the control from Lockout Conditions

Page 63

How to reset the control from Lockout Conditions:

WARNING

The following procedure is for service and installation personnel only. Resetting lockout conditions without correcting the malfunction can result in a hazardous condition.

If an error code is displayed (except for #4, low flame sense current), the water heater will be in a “lockout condition” with the water heater display showing the error code number and “Service Needed” in the status section of the display window. Error codes 62 (maximum number of retries detected) and 63 (maximum number if ignition recycles detected) are “Soft Lockouts” in which the control can be reset in the “User Mode” by pressing the lower right button under “Lockout Reset” shown in the lower right portion of the display. The control will also go through 3 attempts to relight the burners every hour in the soft lockout condition.

Resetting Error Codes in Soft Lockout Condition

Error Code Shown in

Water Heater Display

Status Service needed

SELECT Lockout RESET%

Press for 2 seconds

All other error codes will put the water heater into a “Hard Lockout” condition, in which the water heater will not operate and cannot be reset in the “User Mode”. To reset a hard lockout, first enter the “Service Mode” described earlier by pressing both the “Temperature Up” and “Select Buttons” at the same time for 3 seconds. Then press the lower right button under “Lockout Reset” in the water heater display and hold for 3 seconds.

Resetting Error Codes in Hard Lockout Condition

Error Code Shown in

Water Heater Display

Status Service Needed

 

%

SELECT

SET

&Step 1: Press for 3 seconds to enter service mode.

Status Service Needed

SELECT Lockout RESET

Step 2: Press for 3 seconds to reset control in service mode.

63

Page 62 Page 64
Image 63
Page 62 Page 64
Contents What to do if YOU Smell GAS With Troubleshooting GuideTable of Contents Page Do not Operate the Appliance Until the Leakage is Corrected Dimensions Inches Section II SpecificationsSection III General Information FeaturesTemperature and Pressure Relief Valve Condensate Elbow With Trap Do not Operate the Appliance Until the Leakage is Corrected Section IV Installation InstructionsUnpacking Minimum Clearance To Combustible Material Location Remove CrateAIR Requirements Confined Space Typical Installation IllustrationMechanical Exhausting of Room AIR Unconfined SpaceTypical Front Inlet Connection Typical Two Water Heater Connection Section V Water Connections Instructions for ConnectionsScalding Alternate Space Heating Water Connections Approximate TIME/TEMPERATURE Relationships in ScaldsSection VI Venting Page Venting Direct Vent InstallationCanadian US Installations2 Installations1 Direct Vent Terminal Clearances Page Typical Horizontal Direct Vent System Typical Vertical Direct Vent System Installation Cm PVC, Cpvc Power Vent InstallationPage Typical Horizontal Power Vent System Typical Vertical Power Vent System Installation Power Vent Maximum Vent Length Multiple INTAKE/EXHAUST Terminal Separation Distances Concentric Vent Terminal Installation Procedure Vertical InstallationRain Cap to Small Vent Pipe Assembly Vent Pipe Preparation Horizontal InstallationSection VII GAS Connections Initial PreparationSelection of Materials GAS Pressure Regulation GAS Meter Size Natural Gases onlySection Viii Electrical Connections Wiring Diagram and SchematicSequence of Operation Section IX Operating InstructionsGeneral Instructions To Fill the Water HeaterLighting and SHUT-DOWN Instructions For Your Safety Read Before LightingTemperature Adjustment Read Operational Status IndicatorOr Service Needed Reads Idle or HeatingSetpoint flashes for 10 seconds Press SET Button for setting to take effect immediatelyTo Decrease Setpoint Temperature Changes to C Press selectPress select Step Symbol F/C Stops FlashingPress Set Setpoint shown in FSection X Maintenance GeneralBurner Flame Check Sight Glass Location Maintenance ScheduleSediment and Lime Scale Removal Flushing Water HeaterDraining Water Heater Filling Water HeaterAnode Inspection and Replacement Drain Valve and Tank Access PanelRelief Valve Combustion System Inspection Vent and AIR Intake SystemSection XI Diagnostic and Troubleshooting Guide Max Setpoint Next to Temperature Setpoint value Max Setpoint value Water Heater Display Water Heater DisplayHeating No current error codes Max Setpoint Flashes Max Setpoint stops flashing Max Setpoint continues to flashTo Display Flame Sense Current of the Pilot Flame Sensor Display of Water TemperatureSetpoint Flashes To Display and Change Temperature SetpointSetpoint Stops Flashing Flashes Changes to C F/C FlashesSymbol Stops Flashing Press for 3 seconds to reset control in service mode How to reset the control from Lockout ConditionsResetting Error Codes in Soft Lockout Condition Resetting Error Codes in Hard Lockout ConditionError Code History To view previous error codesNo Current Error Code No Error Code Shown for Code Index Error Code IndexStored Error Code For Code Index #9 ExitingSELECTServiceSETMode Page Procedure for Checking Thermostat Sensors EF Series Water Heater Section XII Parts ListCombustion Surround Assembly Ignition Control Assembly Combustion Assembly pictured previous
Related manuals
Manual 76 pages 32.48 Kb

EFR-1-60T1206EN, EFR160T120 specifications

Bradford-White Corporation is a leading manufacturer of residential and commercial water heating solutions, and one of its standout products is the EFR160T120, also known as the EFR-1-60T1206EN. This innovative electric water heater is designed for those seeking reliable performance, energy efficiency, and long-lasting durability.

The EFR160T120 has an impressive capacity of 60 gallons, making it suitable for households with higher hot water demands. This model features a compact design, allowing it to fit into various installation spaces, such as utility rooms or small basements, without compromising on performance. Its vertical configuration and dimensions ensure that it occupies minimal floor space while delivering optimal hot water supply.

One of the most notable features of the EFR160T120 is its high-efficiency electric heating elements. This water heater is equipped with multiple heating elements that provide quick recovery rates, ensuring that hot water is readily available when it is needed most. The intelligent design employs a top-mounted thermostat that allows for accurate temperature control, promoting consistent hot water delivery for showers, baths, and household chores.

In terms of technology, the EFR160T120 incorporates advanced insulation technology that minimizes heat loss, enhancing energy efficiency. This feature not only contributes to reduced energy bills but also lowers carbon emissions, aligning with modern eco-conscious standards. The unit features an integrated temperature and pressure relief valve, which enhances safety by preventing excessive pressure build-up and protecting the tank from potential damage.

Durability is another strong suit of the EFR160T120, as it is constructed from high-quality materials. The tank is coated with a glass lining that protects against corrosion, extending the overall life of the unit. The heater is also backed by Bradford-White's reputation for quality craftsmanship, providing peace of mind for consumers.

Furthermore, the EFR160T120 is designed with user convenience in mind. Maintenance is straightforward, and replacement parts are readily available, which facilitates easy repairs and servicing. Overall, the Bradford-White EFR160T120 water heater stands out as a reliable and efficient choice for homes that require ample hot water supply without sacrificing space or energy efficiency.
Top Page Image Contents