Features and components

The Eliminator (self-cleaning system)

These units include The Eliminator (Self-Cleaning System) installed in the front water inlet, See Figure 1. The Eliminator inlet tube can only be used in the front water inlet connection. Do not install the Eliminator inlet tube in either the top or back inlet water connection. The Eliminator must be oriented correctly for proper function. There is a marked range on the pipe nipple portion of the Eliminator, that must be aligned with the top of the inlet spud. A label above the jacket hole has an arrow that will point to the marked portion of the pipe nipple if the orientation is correct. If the arrow does not point within the marked range on the pipe nipple, adjust the pipe nipple to correct. A pipe union is supplied with the Eliminator to reduce the probability of misaligning the Eliminator accidentally while tightening the connection to the inlet water supply line. Improper orientation of the Eliminator can cause poor performance of the heater and can significantly reduce outlet water temperatures during heavy draws.

Note: The Eliminator may have 1, 3 or 7 cross tubes.

FIGURE 1

High Limit Switch

The digital thermostat (Figure 2) contains the high limit (energy cutoff) switch. The high limit switch interrupts main burner gas flow should the water temperature reach 203°F (95°C).

In the event of high limit switch operation, the appliance cannot be restarted unless the water temperature is reduced to approximately 120°F (49°C). The high limit reset button on the front of the control then needs to be depressed.

Continued manual resetting of high limit control, preceded by higher than usual water temperature is evidence of high limit switch operation. The following is a possible reason for high limit switch operation:

•A malfunction in the thermostatic controls would allow the gas valve to remain open causing water temperature to exceed the thermostat setting. The water temperature would continue to rise until high limit switch operation.

Contact your dealer or service agent if continued high limit switch operation occurs.

Electronic Ignition Control

Each heater is equipped with an ignition module. The solid state ignition control (Figure 3), ignites the main burner by utilizing a silicon nitride igniter. The silicon nitride igniter shuts off during the heating cycle and the main burner flame is sensed through a remote flame sensor integral to the silicon nitride igniter assembly.

The ignition control will try to ignite the main burner three times before lockout. Then it waits one hour before trying again to ignite the main burners. This is a continuous cycle.

IGNITION CONTROL BOARD

FIGURE 3

Exhaust Inducer (blower assy.)

All models are equipped with an exhaust inducer. The inducer assists in drawing in fresh air to the unit for combustion and then assists in dispensing the combustion by-products into the venting leading outside.

The exhaust inducer is equipped with a gravity controlled damper to reduce the amount of heat loss through the flue, improving efficiency.

DIGITAL THERMOSTAT

FIGURE 2

EXHAUST INDUCER

FIGURE 4

Uncrating

The heater is shipped with the inducer already installed. The wiring conduit runs from the thermostat to the inducer. Before turning unit on, check to make sure the wiring conduit is securely plugged into the inducer.

(A)BCG3 85T500-8N, (A)BCG3 85T500-8P specifications

American Water Heater has long been a trusted name in the industry, providing high-quality solutions for residential and commercial water heating needs. Among its impressive lineup of products, the (A)BCG3 85T500-8P and (A)BCG3 85T500-8N models stand out due to their outstanding efficiency, performance, and innovative technologies.

These water heaters are primarily classified as high-efficiency gas water heaters, designed to meet a variety of usage demands. With a robust design and advanced technological features, they cater to homes and businesses that require reliable and energy-efficient hot water solutions.

One of the most notable features of the (A)BCG3 85T500-8P and (A)BCG3 85T500-8N models is their remarkable thermal efficiency. They are engineered to optimize energy usage, which not only helps reduce utility bills but also minimizes environmental impacts. This energy efficiency is achieved through advanced insulation and heat exchange technologies that maintain water temperature with minimal energy expenditure.

Both models come equipped with a powerful gas burner that allows for rapid heating, making them ideal for high-demand scenarios. The innovative burner technology ensures even heat distribution, significantly reducing recovery time and ensuring that hot water is available whenever needed.

In terms of safety, American Water Heater has incorporated several features to protect users and the unit itself. These include safety shut-off valves and temperature control features that prevent overheating and provide peace of mind.

Durability is another hallmark of these models. Constructed with high-quality materials, they resist the wear and tear commonly associated with traditional water heaters. Furthermore, the design of the (A)BCG3 85T500-8P and (A)BCG3 85T500-8N emphasizes ease of maintenance, allowing for simpler servicing and reduced downtime.

Finally, both models are backed by American Water Heater's commitment to customer satisfaction, supported by comprehensive warranties and reliable customer service. This assurance adds value to their products, making them a preferred choice for consumers seeking efficient and dependable water heating solutions.

In conclusion, the (A)BCG3 85T500-8P and (A)BCG3 85T500-8N models exemplify American Water Heater’s dedication to innovation and efficiency, making them excellent options for anyone in need of advanced water heating technology.