A.O. Smith BTF-75 warranty Do not TRY to Light the Burner by Hand, What to do if YOU Smell GAS

Page 13

FOR YOUR SAFETY READ BEFORE OPERATING

WARNING: If you do not follow these instructions exactly, a fire or explosion

may result causing property damage, personal injury or loss of life.

BEFORE OPERATING: ENTIRE SYSTEM MUST BE FILLED WITH WATER AND AIR PURGED FROM ALL LINES.

A.This appliance does not have a pilot. It is equipped with an ignition device which automatically lights the burner.

DO NOT TRY TO LIGHT THE BURNER BY HAND.

B.BEFORE OPERATING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS:

Do not try to light any appliance.

Do not touch any electric switch;

do not use any phone in your building.

Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

If you cannot reach your gas supplier, call the fire department.

C.Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don’t try to repair it, call a qualified service technician. Force or attempted repair may result in a fire or explosion.

D.Do not use this appliance if any part has been under water. The heater must be replaced.

OPERATING INSTRUCTIONS

1.STOP! Read the safety information above on this label.

2.Turn the “ON/OFF” switch on the blower control box to the “OFF” position.

3.Set the thermostat to the lowest setting. Turn thermostat

dial fully counterclockwise until it stops.

4.This appliance is equipped with a device which automatically lights the burner.

DO NOT TRY TO LIGHT THE BURNER BY HAND.

5. Wait five (5) minutes

to clear out any gas. If

you then smell gas,

STOP! Follow "B" in the

safety information above on this label.

If you don't smell gas, go to the next step.

6.Set thermostat to desired setting.

7.Turn on all electrical power to the appliance.

8.If the appliance will not operate, follow the instructions "TO TURN OFF GAS TO APPLIANCE" and call your technician or gas supplier.

9.WATERTEMPERATUREADJUSTMENT

Turn temperature knob by hand to the desired temperature.

Hot is approximately 120°F.

CAUTION: Hotter water increases the risk of scald injury. Consult the instruction manual before changing temperatures.

WARNING: TURN OFF ALL ELECTRIC

POWERBEFORESERVICING

TO TURN OFF GAS TO APPLIANCE

A.Set thermostat to the lowest setting.

B.Turn off all the electric power to the appliance if service is to be performed.

13

Image 13
Contents SmartValve is a Registered Trademark of Honeywell Inc Commercial GAS, GLASS-LINED, TANK-TYPE Water HeaterALL Dimensions in Inches ROUGH-IN-DIMENSIONSRecovery Capacities ForewordGeneral Safety Information Table of ContentsInstallation Unconfined Space AIR RequirementsConfined Space Water ConnectionsClosed Water System Venting Single TemperatureRelief Valve Vent Pipe TerminationIf using 4 inch vent pipe If using 3 inch vent pipePlanning the Vent System Number Maximum Elbows Pipe FeetVent Terminal INSTALLATION, Sidewall Installation of Sidewall Vent SystemPreparation of Blower Assembly Power Vent Wiring Schematic Figure Installation of Vertical Vent System Installation of Vent SYSTEM, SidewallVent Pipe Preparation Initial PreparationCement PrimerMaking the Joint Step aGAS Connections OperationConnection of GAS Pipe To Operate the HeaterDo not TRY to Light the Burner by Hand WatertemperatureadjustmentWhat to do if YOU Smell GAS Do not TRY to Light the Burner by HandTemperature Regulation MaintenanceWater Temperature Adjusting Dial PurgingPower Venter Maintenance High Temperature CUT-OFF SwitchVenting System ValveTrouble Shooting Service and RepairCondensation Cathodic PROTECTION-ANODEVent Pipe TOO HOT TroubleshootingAbove 170 F Yellow FlameOFF Troubleshooting with the LEDFlash YES Check for Proper Voltage ATTurn on GAS Supply Plug Replace HSIClaim Procedure Service and Repair ExpensesTank ALL Other Parts