ROUGH-IN-DIMENSIONS
TOP VIEW
*INSTALL IN ACCORDANCE WITH LOCAL CODES
|
|
|
|
|
|
|
|
|
|
|
|
|
| FIGURE 1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
| ALL DIMENSIONS IN INCHES |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Model |
| Units | A |
| B |
| C |
| D | E |
| F |
| G |
| H |
| J |
|
| K |
| L |
|
| M |
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
| Inches | 66 5/16 |
| 58 1/2 |
| 29 5/8 | 25 3/8 | 15 3/16 | 4 |
|
| 14 |
|
| 16 |
| 1 1/4 |
| 1 |
| 1/2 |
| 11 | 15/16 |
|
|
| |||||||||||
|
|
|
|
|
| cm | 168.4 |
| 148.6 |
| 75.2 | 64.5 | 38.6 |
| 10.2 |
| 35.6 |
| 40.6 |
| 3.2 |
| NPT |
| NPT |
| 30.3 |
|
|
| ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
| RECOVERY CAPACITIES |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||||
|
| Input |
| Approx. | Approx. | Temp. °C |
| 17 | 22 |
| 28 |
| 33 |
| 39 | 44 | 50 |
|
| 56 |
| 61 |
| 67 |
| 72 | 78 | |||||||||||||
Model | Rating |
| Rating |
| Gal. |
| Liter |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
| Btu/Hr |
| KW/Hr |
| Cap. |
| Cap. | Rise ° F |
| 30 | 40 |
| 50 |
| 60 |
| 70 | 80 | 90 |
| 100 |
| 110 |
| 120 |
| 130 | 140 | ||||||||||||
80,000 |
| 23.4 |
|
| 74 |
|
| 284 |
| LPH |
| 979 | 734 |
| 587 |
| 489 |
| 419 | 367 | 326 |
| 294 |
| 267 |
| 245 |
| 226 | 210 | ||||||||||
|
|
|
|
|
|
|
|
|
|
|
| GPH |
| 259 | 194 |
| 155 |
| 129 |
| 111 | 97 | 86 |
|
| 78 |
| 71 |
| 65 |
| 60 | 55 | |||||||
Recovery capacity based on 80% thermal efficiency.
FOREWORD
The design of model
Installation diagrams are found in this manual. These diagrams will serve to provide the installer with a reference for the materials and method of piping necessary. It is highly essential that all water and gas piping be installed as shown on the diagrams.
In addition to these instructions, the equipment shall be installed in accordance with those installation regulations in force in the local area
where the installation is to be made. These shall be carefully followed in all cases. Authorities having jurisdiction should be consulted before installations are made.
The installation must conform to these instructions and the local code authority having jurisdiction. In the absence of local codes, the installation must comply with the latest editions of the National Fuel Gas Code, ANSI Z223.1/NFPA 54. The NFPA. This is available from the Canadian Standards Association, 8501 East Pleasant Valley Road, Cleveland, OH 44131, or the National Fire Protection Association, 1 Batterymarch Park, Quincy, MA 02269.
2