A.O. Smith 317443-000 instruction manual Operational Problems, Fault And Alert Conditions

Page 52

Operational Problems

Read and understand this instruction manual and the safety messages herein before installing, operating or servicing this water heater.

Failure to follow these instructions and safety messages could result in death or serious injury.

This manual must remain with the water heater.

This section of the manual is intended to be an aid in correcting common operational problems, it is not all inclusive. The installer may be able to observe and correct certain problems which might arise when the water heater is first put into operation or when it is re-fired after a prolonged shutdown. However, only qualified service agents should perform any service procedures on the water heater.

Note: Call the technical support phone number listed on the back cover of this manual for further technical assistance or to locate a qualified service agent in your area.

Rough Starting, Rough Operation

Fire and Explosion Hazard

Do not use water heater with any gas other than the gas shown on the rating plate.

Excessive gas pressure to gas valve can cause serious injury or death.

Turn off gas lines during installation.

Contact a qualified installer or service agency for installation and service.

•Undersized supply gas line (low volume of supply gas).

•Low Gas Pressure.

•Excessive supply gas pressure.

•Excessive manifold (offset) gas pressure.

•Incorrect Fuel Type

•Vent (exhaust) gas recirculation at the vent and intake air pipe terminations on Direct Vent installations.

•Excessive equivalent lengths of intake air and/or vent (exhaust) piping installed.

•Clogged/blocked intake air screen(s).

•Clogged/blocked Main Burner.

Momentary Ignition

CAUTION

Burn Hazard

•The combustion chamber and burner sleeve and housing become very hot during operation.

•Do not reach into the burner housing or combustion chamber if the water heater

is still hot.

• Allow the water heater to cool and always use gloves when handling the main burner.

If the Main Burner ignites momentarily but does not sustain ignition allow the water heater to try to ignite up to two more times until control system locks out and the Ignition Failure Fault message is displayed on the control system's LCD. If the water heater is experiencing rough starts - see Rough Starting, Rough Operation on this page. For momentary ignition problems without rough starting check the following:

•Incorrect manifold (offset) gas pressure.

•Undersized supply gas line (low volume of supply gas).

•Low Gas Pressure

•See the list of possible causes and things to check and repair for the Ignition Failure Fault message.

•Clogged/blocked intake air screen(s).

•Clogged/blocked Main Burner.

Not Enough Or No Hot Water

•No power to the water heater, check breaker, fuses and the water heater on/off switch.

•Hot water supply valve(s) to fixtures closed.

•Operating Set Point is set too low, Differential setting is set too high.

•Temperature Probe Offset setting are causing the heating cycles to terminate prematurely.

•The heating capacity of the water heater has been exceeded, the water heater is unable to meet demand.

•Colder incoming water temperature lengthening the time required to heat water to desired temperature.

•Hot water piping leaks, open faucets, water heater drain valve leaking or open.

•Sediment or lime scale accumulation may be affecting water heater operation.

Water Is Too Hot

•Operating Set Point is set too high.

•Temperature Probe Offset settings improperly set.

Noisy Operation

•Normal operating noise of electrical components; Combustion Blower, transformer hum, relay contact closure.

Replacement Parts

Replacement parts may be ordered from the manufacturer, authorized service agencies or distributors. When ordering parts be sure to have the complete water heater Model Number, Serial Number and Series Number available. This information can be found on the rating plate affixed to the water heater.

Refer to the parts list for more information or call the parts department or technical support phone number listed on the back cover of this manual for further assistance.

Fault And Alert Conditions

Fault Conditions

When the control system declares a Fault condition it will display a Fault message on the control system's LCD with an exclamation "!" mark. The control system will lock out and disable heating operation until the condition is corrected. The water heater must be serviced by a qualified service agent before operation can be restored.

Alert Conditions

When the control system declares an Alert condition it will display an Alert message on the control system's LCD with a question "?"

52

Page 51 Page 53
Image 52
Page 51 Page 53
Contents Printed Whenever maintenance adjustment or service is required317443-000 Table of contents Safe installation, use and service ApprovalsPrecautions Hydrogen Gas Flammable General safety informationGrounding Instructions General safety information Fire or Explosion Hazard Preparing For The Installation IntroductionAbbreviations Used QualificationsFeatures and components Replacement Parts and Deliming ProductsInstallation consideration Rough in DimensionsRough-In-Dimensions Recovery capacity based on 96% thermal efficiencyProperty Damage Hazard Locating The Water HeaterInsulation Blankets Combustion AIR and VentilationUnconfined Space Confined Space Fresh Air Openings For Confined SpacesOutdoor Air Through Two Openings Outdoor Air Through One OpeningOutdoor Air Through Two Horizontal Ducts Air From Other Indoor SpacesInstalling the new water heater Power SupplyChemical Vapor Corrosion Water PipingDishwashing Machines Mixing ValvesSpace heating and potable water system Thermal Expansion Closed Water SystemsValve and Pipe Insulation if supplied Temperature-Pressure Relief Valve Valve Discharge Pipe RequirementsGas piping Condensate PipingHigh Altitude Installations Sediment Traps Filling the Water HeaterVent Pipe Termination VentingPlanning the Vent System Installation of Vent System Vent Terminal INSTALLATION, SidewallInstallation Requirements Commonwealth of Massachusetts Installation of Carbon Monoxide DetectorsApproved Carbon Monoxide Detectors SignageTermination Clearances Sidewall Power Vent Power VentTermination Clearances Sidewall Direct Vent Direct VentInstallation Sequence Sequence of INSTALLATIONS, aVent Termination a Direct Vent terminal installation Vent Terminals Supplied with Heater Must be UsedFlat Roof Installation Concentric vent installation Safety ConsiderationsKIT Components Description QtyConcentric Termination Flat Roof Clearance MULTI-CONCENTRIC Vent Terminations Direct vent diagram Vent Pipe Preparation Step B Step EStep F Step GBlower Prover Switch Blocked Exhaust SwitchBlocked Intake Switch ON/OFF SwitchPower Vent Wiring Schematic Figure What to do if YOU Smell GAS Do not try to light the burner by handDo not TRY to Light the Burner by Hand Temperature regulation HI Limit Switch ECOOverview Control system operationControl System Navigation Icon Description Status IconsOperating States Control System MenusUser Settings & Control System Menus Temperatures Operating Set Point And Differential AdjustmentTemperatures Heater StatusECO Contact , Blocked Inlet PS , Blocked Outlet PS , Blower Blower Low On , Blower High On displays whetherDisplay Settings Heater InformationCurrent Fault Fault HistoryFault Occurrence Restore Factory DefaultsService Contact Information Service Contact InformationStart UP Conditions For your informationOperational Conditions Periodic maintenance Temperature-Pressure Relief Valve OperationVenting System Inspection Anode ROD InspectionTo drain the water heater storage tank ServiceTo Flush the Water Heater Storage Tank Maintenance Temperature-Pressure Relief Valve TestLeakage checkpoints Troubleshooting Installation ChecklistSequence Of Operation Flow Chart YES noOperational Problems Fault And Alert ConditionsResetting Control System Lock Outs Diagnostic ChecksFault And Alert Messages AC ReversedBlower Prover Failure Page Page Page Limited Warranty Fill in Warranty and Keep for Future Reference

100 Power Vent DV Series 120, 317443-000 specifications

The A.O. Smith 317443-000,100 Power Vent DV Series 120 is an advanced water heating solution designed to enhance efficiency and performance for residential applications. As part of A.O. Smith's renowned lineup, this model embodies the company's commitment to innovation and energy conservation.

One of the main features of the DV Series 120 is its power venting capability. This technology allows for flexible installation options, as it can vent vertically or horizontally, accommodating various home configurations. It utilizes a fan-assisted venting system, which efficiently expels exhaust gases, ensuring safe operation even in tight spaces.

The unit's energy efficiency is another standout characteristic. Equipped with a high-efficiency gas burner, the DV Series 120 optimizes fuel consumption, resulting in lower utility bills while providing reliable hot water when needed. Its impressive Energy Factor (EF) ratings make it an environmentally friendly choice, aligning with modern standards for green building practices.

Durability is also a significant focus of the A.O. Smith 317443-000,100 Power Vent model. Constructed with a glass-lined tank and a robust anode rod, this water heater is designed to resist corrosion and extend its lifespan. This construction enhances performance reliability while minimizing maintenance needs, making it a smart investment for homeowners.

Smart technologies are integrated into the DV Series 120, featuring an intelligent control system that provides various operational insights. The built-in diagnostic features allow homeowners to monitor performance and identify potential issues early, reducing the likelihood of unexpected failures. This control system can also enable more precise temperature management, enhancing both comfort and efficiency.

Safety is paramount in the design of the A.O. Smith 317443-000,100. The unit comes equipped with safety features such as a built-in flame rollout sensor and an automatic shut-off system to protect against potential hazards. These features ensure peace of mind for users, allowing them to confidently rely on their hot water supply.

In summary, the A.O. Smith 317443-000,100 Power Vent DV Series 120 stands out as a high-efficiency water heating solution, combining innovative venting technologies, durability, smart features, and safety mechanisms. This model is an ideal choice for homeowners seeking a reliable and efficient hot water system that meets modern energy standards.
Top Page Image Contents