Allstar Products Group AC9500, AC9300, ACJ9500 owner manual Adjustment #1 Opening Travel

Page 17

E:OPERATION AND ADJUSTMENT INSTRUCTIONS

OPTIONAL THREE FUNCTION DELUXE WALL STATION

When the Wall Station is connected to the operator per instructions supplied with the wall station, it will provide the following features:

1.“OFF-ON” will prevent inadvertent operation of the door from any other push button, radio or keyless entry device. It will also as additional protection from unwanted operation during absence of the owner. This feature is to be activated only when the door is at the full open or close position and never while the door is moving.

2.“LIGHT” button allows the convenience light to be turned on and stay on until turned off by a second push of the button or activation of the door cycle.

3.“UP/DOWN” button provides normal opening and closing of the door by momentary activation of this push button. Function of door cycle is described above - “How the Door Moves When the Opener is Activated”.

DO NOT USE ADJUSTMENTS TO COMPENSATE FOR A POORLY WORKING DOOR. THIS WILL INTERFERE WITH THE PROPER OPERATION OF THE REVERSING MECHANISM AND MAY DAMAGE THE DOOR.

Adjustment #1: Opening Travel

Your opener is assembled at the factory with the trolley in the forward position with the open limit stops snapped in place on the chain, set for a standard door.

If you door is non-standard, move BOTH open limit stops, located just behind the trolley. As an example: For a 6 FT, 6 INCH door, move both open limit stops six inches or 12 links toward the power head unit.

To confirm final opening travel adjustment, activate the opener to bring the foor to the fully open position. When properly adjusted, center of the open limit stops should come to rest opposite the load adjusting nut.

110056-1

 

 

 

 

Load Adjusting Nut

 

 

 

 

 

 

 

 

 

Limit Stops

 

 

NOTE: If the door drifts forward, move the open limit stops toward the power head unit. If the door does not drift forward it is still advised that you perform one additional check. Operate manual release on the trolley and allow the door to seek its natural fully open position, then move the open limit stops to align trolley to this position. If the door does not open fully at its natural open position, it indicates a door spring or hardware problem that should be referred to a door system professional.

(See instruction label on side of track for proper limit stop location.)

Limit Stops

Chain

Leave One Link Open Between

the Two Open Limit Stops

Adjustment #2: Opening and Closing Force

 

 

 

 

Hex nuts for adjusting force are located on either side of the rail at the motor end.

 

 

 

 

 

110056-2

 

 

Close Adjustment Nut

The left hex nut, labeled “CLOSE”, adjusts the closing force; the right hex nut,

 

 

 

 

 

 

labeled “OPEN”, adjusts the opening force.

 

 

 

 

Turning the hex nuts clockwise increases force; counterclockwise decreases force.

 

 

 

 

Your garage door opener is built with a safety system that allows the door to reverse

 

 

 

 

in the close direction and stop in the open direction. This must be adjusted so your

 

 

 

 

opener does not use excessive force in the down direction or react to the weight of the

 

 

 

 

door during upward travel.

 

 

 

 

To help determine that the force is not excessive, grasp the door handle or bottom

 

 

 

 

Open Adjustment Nut

edge during downward travel. The opener should reverse to this force. Do not stand

 

 

 

 

 

 

 

 

under the door during this test.

 

 

 

 

If the handle is hard to hold and the door does not reverse, adjust the CLOSE hex nut to decrease force until the door reacts properly.

Repeat the adjustment procedure for upward travel. The door should stop without using excessive force.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Challenger AC9000 Series Table of Contents Optional Features Product FeaturesStandard Features Tools Required Component IdentificationAssembly Instructions Important Installation Instructions Reinforce the Header Wall Installing the OperatorHigh ARC Rise Horizontal Line Return to the Rail/Wall Step110054-2Step 9 Connecting the Door Arm to the Door Connecting Door Arm to TrolleyDoors Using Optional ONE Piece Door ARM Assembly Connecting the Door Arm to the Door ONE PieceFLOOR, OUT of Reach of Children Control and Auxiliary EquipmentWire Connect the Photosystem Safe Finish Photosystem InstallationFinal Installation of Photosystem Units Control and Auxiliary EquiipmentTransmitter Installation of Radio ControlsHOW to Activate the Opener Operation and Adjustment InstructionsTurning on Power to the Operator Basic Operating Parameters HOW the Light Works and What IT Means When IT Flashes HOW the Door Moves When the Opener is ActivatedHOW to Operate the Door Manually Manual Release Disconnect No ONE should Cross the Path of a Moving DoorOptional Three Function Deluxe Wall Station Adjustment #1 Opening TravelAdjustment #2 Opening and Closing Force Repeat this Test Monthly Adjustment #3 Setting Door Close LimitAdjustment #4 Obstruction Sensing Closing Direction Important Test Photoelectric Obstruction Test Adjustment #6 Positive Mechanical Lock AdjustmentAdjustment #7 Resetting the Travel Timer Maintenance of Your Opener Safe Finish Wiring Diagram / Maintenance ScheduleInstallation Checklist Symptom Probable CAUSE/SOLUTION Troubleshooting GuideSolution Probable CauseParts Breakdown & Listing Allstar Corporation Downingtown, PA

AC9300, AC9500, ACJ9500 specifications

Allstar Products Group has established a strong reputation in the field of automotive accessories, and their line of ACJ9500, AC9500, and AC9300 models exemplifies this commitment to quality and functionality. These units are designed to cater to a wide range of needs, enhancing vehicle performance and user convenience.

The ACJ9500 is particularly noteworthy for its impressive power output and versatility. It is equipped with a robust motor that delivers efficient performance, making it suitable for various applications, from automotive work to home improvement tasks. One of its standout features is the adjustable speed setting, allowing users to customize the airflow according to their specific needs. This model also includes a durable construction that ensures longevity, even under demanding conditions.

Moving on to the AC9500, this unit is celebrated for its compact design, which does not compromise on power or efficiency. It is lightweight and portable, making it an ideal choice for individuals who require a reliable tool that can be easily transported. The AC9500 is equipped with user-friendly controls that simplify operation, ensuring that even those with minimal experience can quickly get the hang of it. Its noiseless operation is another significant advantage, perfect for environments where quiet is essential.

The AC9300 model rounds out the lineup with its emphasis on energy efficiency. This unit utilizes cutting-edge technology, which minimizes power consumption while maintaining optimal performance. It is specifically designed to reduce energy waste, making it an environmentally friendly option for customers who are conscious of their ecological footprint. The AC9300 also features a unique ventilation system that enhances airflow, promoting better circulation and cooling, which is especially valuable in automotive applications.

In summary, the Allstar Products Group models ACJ9500, AC9500, and AC9300 deliver a combination of power, efficiency, and user-friendly features that cater to diverse needs. Their innovative technologies and durable designs showcase Allstar’s commitment to providing high-quality automotive accessories. Each model stands out for its specific strengths, making them suitable for different tasks and environments. Whether for professional or personal use, these models continue to meet the demands of consumers looking for reliability and performance in automotive tools. The combination of functionality and practicality ensures that Allstar's offerings remain competitive in the market.
Top Page Image Contents