Allstar Products Group AC9500, AC9300, ACJ9500 Connecting the Door Arm to the Door ONE Piece

Page 11

C:INSTALLING THE OPERATOR

Step 10: Connecting the Door Arm to the Door - ONE PIECE

DOORS (USING OPTIONAL ONE PIECE DOOR ARM ASSEMBLY)

Attach door arm brackets to the top surface of the door on the center line.

Reposition Open and Close limit stops so trolley stops in locations as shown. Assemble the door arm by screwing curved rod into straight tube section. Allow approximately 6” of rod to project outside of the straight tube.

Release trolley with red knob handle and move to a convenient position between

Closed Limit

Stop Location

110055-1

 

 

 

Open Limit

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Stop Location

 

 

 

 

 

 

 

 

 

 

 

Fully Closed

 

 

Trolley

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Fully Open

Door Arm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Door Arm

 

 

 

 

Connection

 

 

 

Open Door

 

Door Arm Bracket

 

Door Arm

Closed Door

 

 

 

 

 

 

 

 

 

6”

Door

Brackets

Straight Tube

Bolt/Nut

110054-2

Open and Close limits. Connect curved rod section to trolley.

Slide door arm and trolley toward door; connect the tube assembly to the door bracket with the 3/8” diameter bolt and locking nut, tightening enough to allow for door arm pivot. Do not overtighten the locking nut.

Press door control button and run opener through full open and close cycles, adjusting the limit stops as required to fully open and close the door. At full closed position, the door arm assembly should compress approximately one inch.

STEP 11: Connecting The Electrical Power Consult the label on the rear panel of the Opener to determine its proper working voltage. Normally it will be marked for 115V, 60 cycle operation. (If it is an export model designed for 220V, 50 cycle operation, the label will clearly indicate this.) The Opener must be plugged into a properly grounded receptacle within 3 FT of the Power Unit. A GFI Type receptacle is recommended. Do not use 2-prong adapters and do not use extension cords for anything more than temporary hook-up and testing purposes. Receptacle wiring should be No. 14 or heavier, and must be in compliance with local building and electrical codes.

110053-1Permanent Wiring Connection

Using the two wires (black & white) that were left when you cut off the line cord, splice in the permanent connections.

Normal

 

Ground Wire

Connection

 

 

 

 

 

 

 

WARNING

IMPROPER WIRING COULD CAUSE ELECTROCUTION OR DAMAGE TO CIRCUITRY. FOLLOW LOCAL BUILDING AND ELECTRICAL CODES.

If local codes require permanent wiring, a GFI type circuit breaker is recommended to protect the line. Remove the Strain Relief Bushing and withdraw the Line Cord from the rear of the Power Unit to expose the three insulated connectors. Cut the wire at the rubber jacket of the Line Cord and wire in permanently, employing proper wiring practices. Discard Strain Relief. It is not used with permanent wiring.

Step 12: Install a Rough Service lamp bulb (75 Watt maximum) firmly in the light socket. Light bulbs in Door Openers are subject to vibration during normal operation which may shorten their life spans. Rough Service bulbs, available at most hardware stores, are recommended. Fit Light Diffuser tabs into the panel tabs as shown.

110051-3

Clips

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Challenger AC9000 Series Table of Contents Optional Features Product FeaturesStandard Features Tools Required Component IdentificationAssembly Instructions Important Installation Instructions Reinforce the Header Wall Installing the OperatorHigh ARC Rise Horizontal Line Return to the Rail/Wall Step110054-2Step 9 Connecting the Door Arm to the Door Connecting Door Arm to TrolleyDoors Using Optional ONE Piece Door ARM Assembly Connecting the Door Arm to the Door ONE PieceFLOOR, OUT of Reach of Children Control and Auxiliary EquipmentControl and Auxiliary Equiipment Safe Finish Photosystem InstallationWire Connect the Photosystem Final Installation of Photosystem UnitsTransmitter Installation of Radio ControlsHOW to Activate the Opener Operation and Adjustment InstructionsTurning on Power to the Operator Basic Operating Parameters No ONE should Cross the Path of a Moving Door HOW the Door Moves When the Opener is ActivatedHOW the Light Works and What IT Means When IT Flashes HOW to Operate the Door Manually Manual Release DisconnectOptional Three Function Deluxe Wall Station Adjustment #1 Opening TravelAdjustment #2 Opening and Closing Force Repeat this Test Monthly Adjustment #3 Setting Door Close LimitAdjustment #4 Obstruction Sensing Closing Direction Important Test Photoelectric Obstruction Test Adjustment #6 Positive Mechanical Lock AdjustmentAdjustment #7 Resetting the Travel Timer Maintenance of Your Opener Safe Finish Wiring Diagram / Maintenance ScheduleInstallation Checklist Probable Cause Troubleshooting GuideSymptom Probable CAUSE/SOLUTION SolutionParts Breakdown & Listing Allstar Corporation Downingtown, PA

AC9300, AC9500, ACJ9500 specifications

Allstar Products Group has established a strong reputation in the field of automotive accessories, and their line of ACJ9500, AC9500, and AC9300 models exemplifies this commitment to quality and functionality. These units are designed to cater to a wide range of needs, enhancing vehicle performance and user convenience.

The ACJ9500 is particularly noteworthy for its impressive power output and versatility. It is equipped with a robust motor that delivers efficient performance, making it suitable for various applications, from automotive work to home improvement tasks. One of its standout features is the adjustable speed setting, allowing users to customize the airflow according to their specific needs. This model also includes a durable construction that ensures longevity, even under demanding conditions.

Moving on to the AC9500, this unit is celebrated for its compact design, which does not compromise on power or efficiency. It is lightweight and portable, making it an ideal choice for individuals who require a reliable tool that can be easily transported. The AC9500 is equipped with user-friendly controls that simplify operation, ensuring that even those with minimal experience can quickly get the hang of it. Its noiseless operation is another significant advantage, perfect for environments where quiet is essential.

The AC9300 model rounds out the lineup with its emphasis on energy efficiency. This unit utilizes cutting-edge technology, which minimizes power consumption while maintaining optimal performance. It is specifically designed to reduce energy waste, making it an environmentally friendly option for customers who are conscious of their ecological footprint. The AC9300 also features a unique ventilation system that enhances airflow, promoting better circulation and cooling, which is especially valuable in automotive applications.

In summary, the Allstar Products Group models ACJ9500, AC9500, and AC9300 deliver a combination of power, efficiency, and user-friendly features that cater to diverse needs. Their innovative technologies and durable designs showcase Allstar’s commitment to providing high-quality automotive accessories. Each model stands out for its specific strengths, making them suitable for different tasks and environments. Whether for professional or personal use, these models continue to meet the demands of consumers looking for reliability and performance in automotive tools. The combination of functionality and practicality ensures that Allstar's offerings remain competitive in the market.
Top Page Image Contents