Allstar Products Group AC9300 Adjustment #3 Setting Door Close Limit, Repeat this Test Monthly

Page 18

E: OPERATION AND ADJUSTMENT INSTRUCTIONS

Adjustment #3: Setting Door Close Limit

Confirm trolley close position 9” to 10” between the inside face of the door and the point where the door arm connects to the trolley (see illustration).

If adjustment of the close trolley position is necessary, activate the opener and move the trolley 12” to 18” to provide access to the “Limit Stop” devices (mounted on the chain). Move the limit stop to establish the correct trolley close position as above.

Relocation of “Limit Stop” toward the door increases down travel. Relocation of the limit stop away from the door reduces down travel. Note that each chain link provides 1/2” adjustment of trolley travel.

 

9”to10”

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Trolley

 

 

 

 

 

 

(Close Limit Position)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Chain

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Limit Stop

 

 

 

 

 

 

 

 

 

 

 

 

Door

Cushion Arm

 

 

 

 

 

 

 

Bracket

 

 

Assembly

 

 

 

 

 

 

 

 

 

 

110054-1

 

 

 

 

 

 

 

 

 

 

 

 

Adjustment #4: Obstruction Sensing (Closing Direction)

Your opener is designed to automatically reverse the door during closing travel whenever it comes into contact with an object up to the last 1-1/2 inch of travel above the floor. An object on the floor with a height of less than 1-1/2 inch will cause the door to stop. (Test according to the instructions below.)

If the opener reverses properly with a 2” x 4” laid flat on the garage floor (as the test below) and stops in the fully closed position, proceed to Adjustment #5.

If the door reverses when it comes into contact with the floor, move the close limit stop, located on the left side (inside looking out, see figure Adjustment #1), towards the power head unit. It is advised that you move the close limit stop one link at a time and run opener through another close cycle, until the door stops when it comes into contact with the floor.

WARNING

IF LIMITS ARE NOT ADJUSTED PROPERLY, THE EMERGENCY RELEASE MECHANISM MAY NOT WORK PROPERLY AND DOOR OPERATION COULD RESULT IN DOOR DAMAGE, SERIOUS PERSONAL INJURY OR DEATH!

When the door comes into contact with a 2” x 4” laid flat on the garage floor and stops intends of reversing, move the close limit stop away from the power head unit. It is advised that you move the close limit stop one link at a time and run opener through another close cycle, until the door reverses when it comes into contact with the 2” x 4”.

Important Test: Opener Obstruction Sensing Feature for Doors (both Sectional and One Piece)

A.Activate door to the Open position.

B.Place 2” x 4” laid flat on garage floor under path of the door. See Figure.

C Activate door to close position; upon contacting solid object, the door should stop, then reverse direction within 2 seconds and travel to the full open position.

Note: If the fails to pass this test, see Adjustment 3 above and move the Close Limit Stop one increment towards the door to increase down travel. Also review Steps 8 and 9, Page 10 for Sectional Doors or Step 10, Page 11 for One Piece Doors.

110055-3

Solid Test Object

REPEAT THIS TEST MONTHLY!

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Challenger AC9000 Series Table of Contents Product Features Standard FeaturesOptional Features Component Identification Tools RequiredAssembly Instructions Important Installation Instructions Installing the Operator Reinforce the Header WallHigh ARC Rise Horizontal Line Step Return to the Rail/WallConnecting Door Arm to Trolley 110054-2Step 9 Connecting the Door Arm to the DoorConnecting the Door Arm to the Door ONE Piece Doors Using Optional ONE Piece Door ARM AssemblyControl and Auxiliary Equipment FLOOR, OUT of Reach of ChildrenFinal Installation of Photosystem Units Safe Finish Photosystem InstallationWire Connect the Photosystem Control and Auxiliary EquiipmentInstallation of Radio Controls TransmitterOperation and Adjustment Instructions Turning on Power to the Operator Basic Operating ParametersHOW to Activate the Opener HOW to Operate the Door Manually Manual Release Disconnect HOW the Door Moves When the Opener is ActivatedHOW the Light Works and What IT Means When IT Flashes No ONE should Cross the Path of a Moving DoorAdjustment #1 Opening Travel Adjustment #2 Opening and Closing ForceOptional Three Function Deluxe Wall Station Adjustment #3 Setting Door Close Limit Adjustment #4 Obstruction Sensing Closing DirectionRepeat this Test Monthly Adjustment #6 Positive Mechanical Lock Adjustment Adjustment #7 Resetting the Travel TimerImportant Test Photoelectric Obstruction Test Safe Finish Wiring Diagram / Maintenance Schedule Maintenance of Your OpenerInstallation Checklist Solution Troubleshooting GuideSymptom Probable CAUSE/SOLUTION Probable CauseParts Breakdown & Listing Allstar Corporation Downingtown, PA

AC9300, AC9500, ACJ9500 specifications

Allstar Products Group has established a strong reputation in the field of automotive accessories, and their line of ACJ9500, AC9500, and AC9300 models exemplifies this commitment to quality and functionality. These units are designed to cater to a wide range of needs, enhancing vehicle performance and user convenience.

The ACJ9500 is particularly noteworthy for its impressive power output and versatility. It is equipped with a robust motor that delivers efficient performance, making it suitable for various applications, from automotive work to home improvement tasks. One of its standout features is the adjustable speed setting, allowing users to customize the airflow according to their specific needs. This model also includes a durable construction that ensures longevity, even under demanding conditions.

Moving on to the AC9500, this unit is celebrated for its compact design, which does not compromise on power or efficiency. It is lightweight and portable, making it an ideal choice for individuals who require a reliable tool that can be easily transported. The AC9500 is equipped with user-friendly controls that simplify operation, ensuring that even those with minimal experience can quickly get the hang of it. Its noiseless operation is another significant advantage, perfect for environments where quiet is essential.

The AC9300 model rounds out the lineup with its emphasis on energy efficiency. This unit utilizes cutting-edge technology, which minimizes power consumption while maintaining optimal performance. It is specifically designed to reduce energy waste, making it an environmentally friendly option for customers who are conscious of their ecological footprint. The AC9300 also features a unique ventilation system that enhances airflow, promoting better circulation and cooling, which is especially valuable in automotive applications.

In summary, the Allstar Products Group models ACJ9500, AC9500, and AC9300 deliver a combination of power, efficiency, and user-friendly features that cater to diverse needs. Their innovative technologies and durable designs showcase Allstar’s commitment to providing high-quality automotive accessories. Each model stands out for its specific strengths, making them suitable for different tasks and environments. Whether for professional or personal use, these models continue to meet the demands of consumers looking for reliability and performance in automotive tools. The combination of functionality and practicality ensures that Allstar's offerings remain competitive in the market.
Top Page Image Contents