Allstar Products Group LT 50 owner manual Tance is inadequate Try moving

Page 15

D: AUXILIARY EQUIPMENT

INSTALLATION OF RADIO CONTROLS:

The following instructions detail installation of Model 9931 Radio Controls. For other Radio models, see instructions pack- aged with product.

TRANSMITTER: To gain access to the Transmitter Coding Switches, remove the Battery Cover from the front of the Transmitter by slid- ing it toward the bot- tom of the Transmit- ter as

illustrated.

104384

RECEIVER: The Receiver Coding Switches can be ac- cessed by removing the small door from the back of the Receiver using a small screwdriver or knife.

104385

Setting The Coding Switches: When setting the Coding Switches THE FACTORY PRE-SET CODES MUST BE CHANGED TO PREVENT UNAUTHORIZED OPER- ATION. Transmitter and Receiver codes must be set IDENTICALLY. If just one Code Switch is mismatched, the Radio Controls will not function.

NOTE: For security reasons, it is advisable NOT to set all the switches in the same position.

Mounting The Receiver: After setting the Coding Switches, mount the Receiver on the rear panel of the Opener by connecting it to Terminals 1, 2 and 3. For proper operation, the Antenna Wire should be POINTED STRAIGHT DOWN toward the floor.

After installing the Radio Con- trols, check their operation by moving approximately 35 FT away from the garage door and pressing the Transmitter Button. Operation at this distance should be reliable.

104386

CODING BLOCK: Transmitter and Receiver Coding Switches are contained in identical Coding Blocks, consisting of nine small switches, labeled 1 - 9, each of which can be set in any of three positions, labeled +, 0, -

 

If the Transmitter

doesn't acti-

 

vate door operation, check that

 

all Coding Switches are set iden-

 

tically. If the operational dis-

POINT ANTENNA

tance is inadequate,

try moving

STRAIGHT DOWN

108386

the position of the Transmitter in

the car. If

the distance is still

inadequate, try

104388

bending the

Antenna Wire to a different angle. If

 

the distance is still inadequate, replace the Battery with a standard 9-Volt “transistor radio” Battery (NEED 1604). The Battery is located in the front compartment next to the Coding Switches.

The Transmitter may be hand held if desired by removing the Visor Clip from the rear of the Case as illustrated. Place your finger in the loop at the top of the visor, and your thumb on the top edge of the Transmitter. Push down with your thumb and

pull up with your finger. The clip will release and pull out easily.

WARNING

TO PREVENT THE RISK OF PERSONAL INJURY, DAMAGE TO DOOR OR PROPERTY, ONLY OPERATE DOOR CONTROLS WHEN DOOR IS IN CLEAR VIEW. KEEP REMOTE CONTROL AWAY FROM CHILDREN IN SECURE AREA.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Allstar LT Table of Contents Product Features Standard FeaturesOptional Features Tools Required Component IdentificationAssembly Instructions Page Reinforce the Header Wall Installing the OperatorSectional Doors and ONE-PIECE Doors With Track Door Bracket Installation Mount Power Head to CeilingProvided to Terminals 1 & 0 on the Openers rear Install a Rough Service lamp bulb 75 WattConnecting The Electrical Power Connect the standard wall Push ButtonMounting the Photosystem Wall Brackets Select a mounting Optional Safe Finish Photosystem InstallationWire Connect the Photosystem Final Installation of Photosystem UnitsAlignment and Initial Test of Safe Finish Photosystem AT this Point Plug Connect the Power to the OperatorConnecting the Door Arm to the Door Connecting Door Arm to TrolleyPhotoelectric Obstruction Test Important Test Opener Obstruction Sensing FeatureTance is inadequate Try moving Adjustment #3 Obstruction Sensing at Close Limit Position AdjustmentsAdjustment #1 Opening Travel Adjustment #2 Opening and Closing ForceChecking the Travel Timer Adjustments / Important Safety InstructionsAdjustment #3 Obstruction Sensing Closing Direction Adjustment #4 Positive Mechanical Lock AdjustmentOperation of Your Opener Operating InstructionsOptional Three Function Wall Station HOW to Operate the Door Manually Manual Release DisconnectOptional Pneumatic Door Edge Installation Safe Finish Wiring Diagram / Door Edge InstallationMaintenance Schedule / Installation Checklist Maintenance of Your OpenerInstallation Checklist Symptom Probable CAUSE/SOLUTION Troubleshooting GuideParts Breakdown & Listing Allstar Corporation Downingtown, PA Manufacturer’s Limited Warranty

LT 50 specifications

Allstar Products Group LT 50 is a versatile and innovative product that has garnered attention for its efficiency and practicality. Designed with the modern consumer in mind, the LT 50 excels in various applications, making it a valuable addition to any home or workspace.

One of the standout features of the LT 50 is its impressive performance capabilities. Equipped with a powerful motor, this device is engineered to deliver quick and reliable results, whether it’s for light-duty tasks or more demanding jobs. The motor is designed to operate quietly, which enhances user experience, allowing for use in environments where noise might be a concern.

The LT 50 integrates advanced technologies that contribute to its ease of use and versatility. It boasts an ergonomic design, which ensures that the user can comfortably handle the device for extended periods. This thoughtful design extends to its controls, which are user-friendly and intuitive. The layout of buttons and switches allows for seamless operation, making it ideal for both seasoned users and novices alike.

Built with durability in mind, the LT 50 uses high-quality materials that withstand wear and tear over time. This longevity ensures that the product remains reliable throughout its lifespan, providing excellent value for consumers who seek dependable performance. Additional safety features are incorporated to prevent accidents and enhance user protection, making it a smart choice for families.

In terms of versatility, the LT 50 can be adapted for a range of tasks. Whether it’s household projects, maintenance work, or creative endeavors, this product has proven to be highly efficient. Its compact size makes it easy to store, and its lightweight construction facilitates portability, allowing users to take it wherever it's needed without hassle.

Furthermore, the LT 50 boasts excellent energy efficiency, making it an environmentally friendly option. By minimizing energy consumption while maximizing performance, it aligns perfectly with sustainable practices, catering to the growing number of eco-conscious consumers.

In conclusion, Allstar Products Group LT 50 is a well-rounded product that emphasizes performance, durability, and user-friendliness. Its innovative features and reliable technology make it an essential tool for everyday tasks, ensuring that consumers can tackle projects with ease and confidence. With the LT 50, users can expect nothing short of quality and efficiency in their endeavors.
Top Page Image Contents