Allstar Products Group LT 50 owner manual Product Features, Standard Features, Optional Features

Page 3

The purpose of this booklet is to provide assembly,

installation and operation information concerning the Allstar LT 50 Commercial Vehicular Garage Door Openers and related Accessory Products.

NOTICE

IT IS IMPORTANT THAT THIS INSTRUCTION

MANUAL BE READ AND UNDERSTOOD

COMPLETELY BEFORE INSTALLATION OR

OPERATION IS ATTEMPTED.

NOTICE

THE IMPORTANT SAFEGUARDS AND

INSTRUCTIONS IN THIS MANUAL CANNOT COVER ALL POSSIBLE CONDITIONS AND SITUATIONS WHICH MAY OCCUR DURING ITS USE. IT MUST BE UNDERSTOOD THAT COMMON SENSE AND CAUTION MUST BE EXERCISED BY THE PERSON(S) INSTALLING, MAINTAINING AND OPERATING THE EQUIPMENT DESCRIBED HEREIN. DO NOT USE THIS EQUIPMENT FOR ANY OTHER THAN ITS INTENDED PURPOSE - OPERATING OVERHEAD GARAGE DOORS.

The Model LT 50 drawbar operators are used in the following applications:

-Restricted Duty, Limited Cycle Commercial installations only.

-Rate of operation shall not exceed 6 cycles of openings and closings per hour, maximum of 40 cycles per day.

-Indoor Use Only.

-Up to 12 foot high doors with a maximum weight of 400 pounds.

-Use with Safe Finish™ Photosystem (light beam across the door opening) or foam/pneumatic reversing edge door components - REQUIRED where the push button is out of sight of the door or any other automatic, remote or manual control is used to activate the door.

STANDARD FEATURES:

Sensing System: A built-in sensing system detects obstructions during door operation. If in the downward (close) travel mode, the Opener will sense an obstruction and reverse the direction of the door. In the open mode, the Opener will stop. Since all doors are different, the Sensing System has independent adjustments for customizing the level of force required for the normal opening and closing of specified doors. ( Page 16)

Close Limit Switch: In winter months it's common for small pieces of ice or packed snow to be trapped under the door. Ground swelling can also effect the close limit setting of the Opener. The LT 50 Close Limit Switch overrides the Sensing System during the last one inch of closing travel and prevents the door from reversing if it encounters an obstruction at this point.

PRODUCT FEATURES

Alternating Action Operation: The mechanical wall pushbutton functions in an Open/Stop/Close/Stop mode in normal operation. (Page 18)

Manual Release: A pull cord allows separation of the drive mechanism and manual operation of the door when desired, as in the event of a power failure. (Page 19)

Automatic Reconnection: Once power is restored, or automatic operation of the door is again desired, initiating operation in the normal manner (Push Button, Radio Control, etc.) will effect automatic reconnection of the Manual Release Mechanism. (Page 19)

Connections For Continuously Monitored Auxiliary Entrapment Protection Devices: The LT 50 Safe Finish™ Photosystem (light beam across the door opening) can be easily connected to the Opener. Control circuitry monitors the device continuously for proper operation. (Page 11) Consult the factory for compatibility of other auxiliary entrapment protection devices.

Momentary Contact To Close: The standard close operation mode is momentary contact of the mechanical Push Button, and a portable Radio Transmitter can be used to close the door (PageZ18). The internal Sensing System (described earlier) detects obstructions in the door’s path.

Constant Contact To Close: For utmost safety, after installation of a Safe Finish™ Photosystem, the standard operation mode can be configured to require constant contact on the mechanical Push Button to close the door if the photosystem fails or if there is a break or short in the wiring. In this mode of operation, a Radio Transmitter cannot be used to close the door. (Page 18)

Safe Finish™ Photosystem: An invisible infrared beam of light guards the door opening and reverses a downward moving door if the beam is broken by a stationary or moving object. The LT 50 motor control circuitry can be configured to constantly monitor the Safe Finish Photosystem for proper operation.

OPTIONAL FEATURES:

Digital Radio Controls: The LT 50 Opener covered in this Manual can be fitted with optional Radio Controls. Up to 19,683 private codes can be easily selected without use of tools. (PageZ15)

Deluxe Wall Push Button: A feature-packed accessory unit, the Deluxe Wall Station allows access to all of the Opener's functions. Open/Close button permits full control of the door’s operation. The Opener's built-in light can be turned on or off independent of door operation. A Security Switch allows the Opener to be deactivated for extended periods of time. (Page 19)

Keyless Entry System: A tamper resistant outdoor keypad, the optional Keyless Entry System permits entry to the garage without use of key or radio transmitter. Easily programmable, it accommodates four separate access codes of 4 digits. Lighted Buttons enhance nighttime use.

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Allstar LT Table of Contents Product Features Standard FeaturesOptional Features Tools Required Component IdentificationAssembly Instructions Page Reinforce the Header Wall Installing the OperatorSectional Doors and ONE-PIECE Doors With Track Door Bracket Installation Mount Power Head to CeilingProvided to Terminals 1 & 0 on the Openers rear Install a Rough Service lamp bulb 75 WattConnecting The Electrical Power Connect the standard wall Push ButtonMounting the Photosystem Wall Brackets Select a mounting Optional Safe Finish Photosystem InstallationWire Connect the Photosystem Final Installation of Photosystem UnitsAlignment and Initial Test of Safe Finish Photosystem AT this Point Plug Connect the Power to the OperatorConnecting the Door Arm to the Door Connecting Door Arm to TrolleyPhotoelectric Obstruction Test Important Test Opener Obstruction Sensing FeatureTance is inadequate Try moving Adjustment #3 Obstruction Sensing at Close Limit Position AdjustmentsAdjustment #1 Opening Travel Adjustment #2 Opening and Closing ForceChecking the Travel Timer Adjustments / Important Safety InstructionsAdjustment #3 Obstruction Sensing Closing Direction Adjustment #4 Positive Mechanical Lock AdjustmentOperation of Your Opener Operating InstructionsOptional Three Function Wall Station HOW to Operate the Door Manually Manual Release DisconnectOptional Pneumatic Door Edge Installation Safe Finish Wiring Diagram / Door Edge InstallationMaintenance Schedule / Installation Checklist Maintenance of Your OpenerInstallation Checklist Symptom Probable CAUSE/SOLUTION Troubleshooting GuideParts Breakdown & Listing Allstar Corporation Downingtown, PA Manufacturer’s Limited Warranty

LT 50 specifications

Allstar Products Group LT 50 is a versatile and innovative product that has garnered attention for its efficiency and practicality. Designed with the modern consumer in mind, the LT 50 excels in various applications, making it a valuable addition to any home or workspace.

One of the standout features of the LT 50 is its impressive performance capabilities. Equipped with a powerful motor, this device is engineered to deliver quick and reliable results, whether it’s for light-duty tasks or more demanding jobs. The motor is designed to operate quietly, which enhances user experience, allowing for use in environments where noise might be a concern.

The LT 50 integrates advanced technologies that contribute to its ease of use and versatility. It boasts an ergonomic design, which ensures that the user can comfortably handle the device for extended periods. This thoughtful design extends to its controls, which are user-friendly and intuitive. The layout of buttons and switches allows for seamless operation, making it ideal for both seasoned users and novices alike.

Built with durability in mind, the LT 50 uses high-quality materials that withstand wear and tear over time. This longevity ensures that the product remains reliable throughout its lifespan, providing excellent value for consumers who seek dependable performance. Additional safety features are incorporated to prevent accidents and enhance user protection, making it a smart choice for families.

In terms of versatility, the LT 50 can be adapted for a range of tasks. Whether it’s household projects, maintenance work, or creative endeavors, this product has proven to be highly efficient. Its compact size makes it easy to store, and its lightweight construction facilitates portability, allowing users to take it wherever it's needed without hassle.

Furthermore, the LT 50 boasts excellent energy efficiency, making it an environmentally friendly option. By minimizing energy consumption while maximizing performance, it aligns perfectly with sustainable practices, catering to the growing number of eco-conscious consumers.

In conclusion, Allstar Products Group LT 50 is a well-rounded product that emphasizes performance, durability, and user-friendliness. Its innovative features and reliable technology make it an essential tool for everyday tasks, ensuring that consumers can tackle projects with ease and confidence. With the LT 50, users can expect nothing short of quality and efficiency in their endeavors.
Top Page Image Contents