Allstar Products Group LT 50 owner manual Adjustments / Important Safety Instructions

Page 17

E:ADJUSTMENTS / IMPORTANT SAFETY INSTRUCTIONS

Adjustment #3: Obstruction Sensing (Closing Direction) cont.

When the door comes into contact with a 2” x 4” laid flat on the garage floor and stops intends of reversing, move the close limit stop away from the power head unit. It is advised that you move the close limit stop one link at a time and run opener through another close cycle, until the door reverses when it comes into contact with the 2” x 4”.

Adjustment #4: Positive Mechanical Lock Adjustment

110057-1

 

 

 

 

 

The garage door opener is designed with an automatic mechanical

 

 

 

“Latch”

locking system. This lock secures the door in the fully closed

 

 

 

position.

 

 

 

To adjust, activate your opener and allow the door to go to its

 

 

 

fully closed position. Loosen the two screws on the rail stop and

 

 

 

move it behind behind the chain latch assembly with a gap of 1/2”

 

 

 

between “stop” and “latch”.

 

 

 

Checking the Travel Timer

 

 

 

Your opener is shipped with the jumper disconnected, allowing the operator to run continuously for up to 29 seconds, then stop in the Open cycle or reverse in the closing cycle.

If your unit will run for only 17 seconds, the operator has mistakenly been shipped with the jumper intact on the control board (perhaps the control board was replaced with a board that still has the jumper installed). On all doors having over 9 feet of travel, it is necessary to cut the run timer jumper on the motor control board to allow the opener to run for 29 seconds. Disconnect the power from the opener before removing cover and cutting the jumper. MAKE SURE YOU DISCONNECT THE POWER BEFORE CUTTING THE JUMPER. THE RUN TIMER WILL NOT CHANGE IF THE JUMPER IS CUT WITH THE POWER CONNECTED.

This jumper is located under operator cover on the control board, as illustrated.

 

 

Stop Limits

Rail “Stop”

 

 

1/2”

110057-2

Cut and

Separate

 

 

IMPORTANT SAFETY INSTRUCTIONS

 

 

 

 

 

WARNING

TO REDUCE THE RISK OF SEVERE INJURY OR

 

 

DEATH, READ AND FOLLOW ALL INSTRUCTIONS!

•Ensure authorized personnel only operate the door. NEVER let children operate or play with door controls. Keep the Remote Control away from children.

•ALWAYS keep a moving door in sight and keep people and objects away from the door area until the door is completely closed. NO ONE SHOULD CROSS THE PATH OF A MOVING DOOR.

•TEST THE DOOR OPENER MONTHLY. The door MUST reverse upon contact with a 1-1/2” high object (or a 2 X 4 board laid flat) on the floor. After adjusting the sensitivity or the limit of travel, ALWAYS RETEST the Opener. Failure to ADJUST THE OPENER PROPERLY may result in SERIOUS INJURY OR DEATH.

•If possible, USE THE MANUAL RELEASE only when the door is closed. Use caution when using the Release with the door open. WEAK OR BROKEN SPRINGS MAY ALLOW THE DOOR TO CLOSE RAPIDLY, CAUSING SEVERE INJURY OR DEATH.

•KEEP THE GARAGE DOOR PROPERLY BALANCED. See the door owner's manual. An improperly balanced door MAY CAUSE SEVERE INJURY OR DEATH. Have a QUALIFIED SERVICE PERSON MAKE REPAIRS TO CABLES, SPRING ASSEMBLIES AND OTHER HARDWARE.

•SAVE THIS INSTRUCTION MANUAL.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Allstar LT Table of Contents Optional Features Product FeaturesStandard Features Tools Required Component IdentificationAssembly Instructions Page Reinforce the Header Wall Installing the OperatorSectional Doors and ONE-PIECE Doors With Track Door Bracket Installation Mount Power Head to CeilingConnecting The Electrical Power Install a Rough Service lamp bulb 75 WattConnect the standard wall Push Button Provided to Terminals 1 & 0 on the Openers rearWire Connect the Photosystem Optional Safe Finish Photosystem InstallationFinal Installation of Photosystem Units Mounting the Photosystem Wall Brackets Select a mountingAlignment and Initial Test of Safe Finish Photosystem AT this Point Plug Connect the Power to the OperatorConnecting the Door Arm to the Door Connecting Door Arm to TrolleyPhotoelectric Obstruction Test Important Test Opener Obstruction Sensing FeatureTance is inadequate Try moving Adjustment #1 Opening Travel AdjustmentsAdjustment #2 Opening and Closing Force Adjustment #3 Obstruction Sensing at Close Limit PositionAdjustment #3 Obstruction Sensing Closing Direction Adjustments / Important Safety InstructionsAdjustment #4 Positive Mechanical Lock Adjustment Checking the Travel TimerOperation of Your Opener Operating InstructionsOptional Three Function Wall Station HOW to Operate the Door Manually Manual Release DisconnectOptional Pneumatic Door Edge Installation Safe Finish Wiring Diagram / Door Edge InstallationInstallation Checklist Maintenance Schedule / Installation ChecklistMaintenance of Your Opener Symptom Probable CAUSE/SOLUTION Troubleshooting GuideParts Breakdown & Listing Allstar Corporation Downingtown, PA Manufacturer’s Limited Warranty

LT 50 specifications

Allstar Products Group LT 50 is a versatile and innovative product that has garnered attention for its efficiency and practicality. Designed with the modern consumer in mind, the LT 50 excels in various applications, making it a valuable addition to any home or workspace.

One of the standout features of the LT 50 is its impressive performance capabilities. Equipped with a powerful motor, this device is engineered to deliver quick and reliable results, whether it’s for light-duty tasks or more demanding jobs. The motor is designed to operate quietly, which enhances user experience, allowing for use in environments where noise might be a concern.

The LT 50 integrates advanced technologies that contribute to its ease of use and versatility. It boasts an ergonomic design, which ensures that the user can comfortably handle the device for extended periods. This thoughtful design extends to its controls, which are user-friendly and intuitive. The layout of buttons and switches allows for seamless operation, making it ideal for both seasoned users and novices alike.

Built with durability in mind, the LT 50 uses high-quality materials that withstand wear and tear over time. This longevity ensures that the product remains reliable throughout its lifespan, providing excellent value for consumers who seek dependable performance. Additional safety features are incorporated to prevent accidents and enhance user protection, making it a smart choice for families.

In terms of versatility, the LT 50 can be adapted for a range of tasks. Whether it’s household projects, maintenance work, or creative endeavors, this product has proven to be highly efficient. Its compact size makes it easy to store, and its lightweight construction facilitates portability, allowing users to take it wherever it's needed without hassle.

Furthermore, the LT 50 boasts excellent energy efficiency, making it an environmentally friendly option. By minimizing energy consumption while maximizing performance, it aligns perfectly with sustainable practices, catering to the growing number of eco-conscious consumers.

In conclusion, Allstar Products Group LT 50 is a well-rounded product that emphasizes performance, durability, and user-friendliness. Its innovative features and reliable technology make it an essential tool for everyday tasks, ensuring that consumers can tackle projects with ease and confidence. With the LT 50, users can expect nothing short of quality and efficiency in their endeavors.
Top Page Image Contents