Allstar Products Group LT 50 owner manual Install a Rough Service lamp bulb 75 Watt

Page 10

C: INSTALLING THE OPERATOR

STEP 7: Install a Rough Service lamp bulb (75 Watt

 

maximum) firmly in the light socket. Light bulbs in Door Openers are

110051-3

 

subject to vibration during normal operation which may shorten their

 

life spans. Rough Service bulbs, available at most hardware stores,

 

are recommended.

 

 

STEP 8: Connect the standard wall Push Button

 

provided to Terminals 1 & 0 on the Opener's rear

108385

panel using a length of 2-conductor, minimum 22 gauge

 

wire. For mounting the standard Push Button, select a

convenient location near an access door. MOUNT AT

LEAST 5 FT FROM THE FLOOR TO DISCOURAGE UNAUTHORIZED OPERATION OF THE DOOR. Install the push button warning label (as shown below) supplied with the Opener near this installation.

If you are installing a Deluxe Wall Push Button), See Page 19 for the proper wiring procedure.

WARNING

UNAUTHORIZED OPERATION OF THE DOOR CONTROLS RISKS INJURY OR DEATH . DO NOT ALLOW ANYONE UNFAMILIAR WITH THE DOOR OPERATION TO OPERATE ANY DOOR CONTROLS. MOUNT THE PUSHBUTTON AT LEAST 5 FT FROM THE FLOOR.

This door is operated by a limited duty operator. To prevent the motor protector from tripping - Do not exceed 6 door cycles per hour.

STEP 9: Connecting The Electrical Power

Consult the label on the rear

 

panel of the Opener to determine its proper working voltage. Normally it will be

WARNING

marked for 115V, 60 cycle operation. (If it is a 230V model the label will clearly

 

 

indicate this.) The Opener

IMPROPER WIRING COULD

Permanent Wiring Connection

must

be

permanently

Use an appropriate

 

wired

with a

proper

CAUSE ELECTROCUTION

L1 & L2

ground

 

connection

OR DAMAGE TO CIRCUITRY.

conduit connector

according

to

all

 

Connections

FOLLOW LOCAL BUILDING

Ground Wire &

 

applicable

local,

state,

 

and federal

building and

AND ELECTRICAL CODES.

Chassis Connection

 

 

 

electrical codes.

Run a

 

 

 

three

(3)

conductor

 

 

 

(minimum

#14,

copper

 

 

 

conductors only) wire from a 15 AMP circuit breaker to the operator in a

 

 

suitable conduit. Use an appropriate connector to secure the conduit to the

 

110442

operator chassis as shown.

Connect the incoming line and neutral power

 

 

wires (L1 and L2) at the terminal block according to the diagram. Secure the

 

 

incoming earth ground to the chassis ground screw as shown .

 

 

NOTE: GFI protection is recommended especially on steel door applications.

10

104350

 

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Allstar LT Table of Contents Standard Features Product FeaturesOptional Features Component Identification Tools RequiredAssembly Instructions Page Installing the Operator Reinforce the Header WallSectional Doors and ONE-PIECE Doors With Track Mount Power Head to Ceiling Door Bracket InstallationConnect the standard wall Push Button Install a Rough Service lamp bulb 75 WattConnecting The Electrical Power Provided to Terminals 1 & 0 on the Openers rearFinal Installation of Photosystem Units Optional Safe Finish Photosystem InstallationWire Connect the Photosystem Mounting the Photosystem Wall Brackets Select a mountingAT this Point Plug Connect the Power to the Operator Alignment and Initial Test of Safe Finish PhotosystemConnecting Door Arm to Trolley Connecting the Door Arm to the DoorImportant Test Opener Obstruction Sensing Feature Photoelectric Obstruction TestTance is inadequate Try moving Adjustment #2 Opening and Closing Force AdjustmentsAdjustment #1 Opening Travel Adjustment #3 Obstruction Sensing at Close Limit PositionAdjustment #4 Positive Mechanical Lock Adjustment Adjustments / Important Safety InstructionsAdjustment #3 Obstruction Sensing Closing Direction Checking the Travel TimerOperating Instructions Operation of Your OpenerHOW to Operate the Door Manually Manual Release Disconnect Optional Three Function Wall StationSafe Finish Wiring Diagram / Door Edge Installation Optional Pneumatic Door Edge InstallationMaintenance of Your Opener Maintenance Schedule / Installation ChecklistInstallation Checklist Troubleshooting Guide Symptom Probable CAUSE/SOLUTIONParts Breakdown & Listing Manufacturer’s Limited Warranty Allstar Corporation Downingtown, PA

LT 50 specifications

Allstar Products Group LT 50 is a versatile and innovative product that has garnered attention for its efficiency and practicality. Designed with the modern consumer in mind, the LT 50 excels in various applications, making it a valuable addition to any home or workspace.

One of the standout features of the LT 50 is its impressive performance capabilities. Equipped with a powerful motor, this device is engineered to deliver quick and reliable results, whether it’s for light-duty tasks or more demanding jobs. The motor is designed to operate quietly, which enhances user experience, allowing for use in environments where noise might be a concern.

The LT 50 integrates advanced technologies that contribute to its ease of use and versatility. It boasts an ergonomic design, which ensures that the user can comfortably handle the device for extended periods. This thoughtful design extends to its controls, which are user-friendly and intuitive. The layout of buttons and switches allows for seamless operation, making it ideal for both seasoned users and novices alike.

Built with durability in mind, the LT 50 uses high-quality materials that withstand wear and tear over time. This longevity ensures that the product remains reliable throughout its lifespan, providing excellent value for consumers who seek dependable performance. Additional safety features are incorporated to prevent accidents and enhance user protection, making it a smart choice for families.

In terms of versatility, the LT 50 can be adapted for a range of tasks. Whether it’s household projects, maintenance work, or creative endeavors, this product has proven to be highly efficient. Its compact size makes it easy to store, and its lightweight construction facilitates portability, allowing users to take it wherever it's needed without hassle.

Furthermore, the LT 50 boasts excellent energy efficiency, making it an environmentally friendly option. By minimizing energy consumption while maximizing performance, it aligns perfectly with sustainable practices, catering to the growing number of eco-conscious consumers.

In conclusion, Allstar Products Group LT 50 is a well-rounded product that emphasizes performance, durability, and user-friendliness. Its innovative features and reliable technology make it an essential tool for everyday tasks, ensuring that consumers can tackle projects with ease and confidence. With the LT 50, users can expect nothing short of quality and efficiency in their endeavors.
Top Page Image Contents