Graco 1050F, 1050H, 1050P, 1050A, 1050C, 1050S Fluid Temperature Range, Non-wetted external parts

Page 23

Technical Data

Non-wetted external parts

Aluminum (1050A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . aluminum, coated carbon steel Hastelloy (1050H). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . hastelloy, stainless steel, polypropylene

or aluminum (if used in center section)

Plastic (1050P, 1050C, and 1050F) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . stainless steel, polypropylene Stainless Steel (1050S) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . stainless steel, polypropylene or alumi-

num (if used in center section)

Reference Information

Maximum Storage Time (varies with conditions) . . . . . . . . . . . . . . . . . . . 2 years Maximum Lifetime (varies with operating conditions and maintenance) . 10 years Power Efficiency Factor (varies based on pump configuration,

operating parameters, and material) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.61 gal. air consumed/1 gal. fluid pumped at 70 psi (1.61 liter air con- sumed/1 liter fluid pumped at 4.8 bar)

*Sound power measured per ISO-9614-2.

**Sound pressure was tested 3.28 ft (1 m) from equipment.

All trademarks mentioned in this manual are the property of their respective owners.

Fluid Temperature Range

NOTICE

Temperature limits are based on mechanical stress only. Certain chemicals will further limit the fluid temperature range. Stay within the temperature range of the most-restricted wetted component. Operating at a fluid temperature that is too high or too low for the components of your pump may cause equipment damage.

 

 

 

 

Fluid Temperature Range

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Polypropylene or

 

 

 

 

Aluminum, Hastelloy, or

 

Conductive

 

 

 

 

Stainless Steel Pumps

 

Polypropylene Pumps

 

PVDF Pumps

Diaphragm/Ball/Seat Material

 

 

 

 

 

 

 

 

Fahrenheit

Celsius

 

Fahrenheit

Celsius

 

Fahrenheit

Celsius

 

 

 

 

 

 

 

 

 

Acetal (AC)

10° to 180°F

-12° to 82°C

 

32° to 150°F

0° to 66°C

 

10° to 180°F

-12° to 82°C

 

 

 

 

 

 

 

 

 

Buna-N (BN)

10° to 180°F

-12° to 82°C

 

32° to 150°F

0° to 66°C

 

10° to 180°F

-12° to 82°C

 

 

 

 

 

 

 

 

 

FKM Fluoroelastomer (FK)*

-40° to 275°F

-40° to 135°C

 

32° to 150°F

0° to 66°C

 

10° to 225°F

-12° to 107°C

 

 

 

 

 

 

 

 

 

Geolast® (GE)

-40° to 150°F

-40° to 66°C

 

32° to 150°F

0° to 66°C

 

10° to 150°F

-12° to 66°C

Polychloroprene overmolded

0° to 180°F

-18° to 82°C

 

32° to 150°F

0° to 66°C

 

10° to 180°F

-12° to 82°C

diaphragm (CO) or Poly-

 

 

 

 

 

 

 

 

chloroprene check balls

 

 

 

 

 

 

 

 

(CR or CW)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Polypropylene (PP)

32° to 150°F

0° to 66°C

 

32° to 150°F

0° to 66°C

 

32° to 150°F

0° to 66°C

 

 

 

 

 

 

 

 

 

PTFE overmolded

40° to 180°F

4° to 82°C

 

40° to 150°F

4° to 66°C

 

40° to 180°F

4.0° to 82°C

diaphragm (PO)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PTFE check balls or two-piece

40° to 220°F

4° to 104°C

 

40° to 150°F

4° to 66°C

 

40° to 220°F

4° to 104°C

PTFE/EPDM diaphragm (PT)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PVDF (PV)

10° to 225°F

-12° to 107°C

 

32° to 150°F

0° to 66°C

 

10° to 225°F

-12° to 107°C

 

 

 

 

 

 

 

 

 

Santoprene® (SP)

-40° to 180°F

-40° to 82°C

 

32° to 150°F

0° to 66°C

 

10° to 180°F

-12° to 82°C

TPE (TP)

-20° to 150°F

-29° to 66°C

 

32° to 150°F

0° to 66°C

 

10° to 150°F

-12° to 66°C

 

 

 

 

 

 

 

 

 

*The maximum temperature listed is based on the ATEX standard for T4 temperature classification. If you are operating in a non-explosive environment, FKM fluoroelastomer’s maximum fluid temperature in aluminum or stainless steel pumps is 320°F (160°C).

312877P

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents 1050P Polypropylene 1050C Conductive Important Safety InstructionsRelated Manuals ContentsDistributor Note To Specify the Configuration of a New PumpTo Order Replacement Parts To Find Your Nearest Distributor1050A A01A Configuration Number MatrixII 2 GD c IIC T4 Atex CertificationsSpecial Conditions for Safe USE Tighten Fasteners Before Setup InstallationFluid supply container Follow local code MountingGrounding Air Line Reed SwitchInstallation of Remote Pilot Air Lines To provide a remote exhaust Air Exhaust VentilationFluid Outlet Line Fluid Supply LineNK L Hastelloy 1050H or Stainless Steel 1050S Fluid Inlet and Outlet PortsAluminum 1050A Fluid pressure relief kit Aluminum pumps only, 1050A models Fluid Pressure Relief ValveFlush the Pump Before First Use Pressure Relief ProcedureStarting and Adjusting the Pump OperationMaintenance Torque sequence Torque InstructionsAluminum 1050A Dimensions and MountingCenter Flange 16.0 in mm Hastelloy 1050H and Stainless Steel 1050S Air Consumption Performance ChartsFluid Pressure Technical Data Non-wetted external parts Fluid Temperature RangeGraco Information Graco Standard Husky Pump Warranty
Related manuals
Manual 32 pages 37.64 Kb

1050P, 1050S, 1050H, 1050C, 1050F specifications

The Graco 1050P is a paint sprayer designed to meet the needs of both professional contractors and DIY enthusiasts. It boasts a range of features and technologies that enhance its performance, efficiency, and ease of use, making it a reliable choice for various painting projects.

One of the standout features of the Graco 1050P is its powerful motor. With a maximum pressure of up to 2800 PSI, this unit is capable of handling thick materials, ensuring a smooth and even application. The robust motor allows users to spray a variety of coatings, including stains, sealers, and even heavy-duty paints, making it versatile for different jobs.

The Graco 1050P incorporates industry-leading Airless Technology, allowing for a high-quality finish without the need for thinning paint. This technology minimizes overspray and ensures that the paint is evenly distributed on the surface, reducing the time needed for touch-ups. The sprayer is equipped with a professional-grade spray gun that enhances control and accuracy, enabling users to achieve precise lines and coverage.

Another important characteristic of this sprayer is its lightweight and portable design. Weighing in at just under 50 pounds, the Graco 1050P is easy to maneuver, making it suitable for both large and small projects. The integrated handle and durable wheels add to its mobility, allowing users to transport it easily around job sites.

The Graco 1050P also features a convenient reversible tip design. This innovation allows users to quickly switch between different spray patterns and sizes, maximizing versatility based on project requirements. If a clog occurs, reversing the tip can clear it instantly, minimizing downtime and maintaining productivity.

For added convenience, the unit is equipped with a durable paint hose that extends up to 75 feet, providing ample reach for those hard-to-reach areas. Its filter system helps keep dirt and debris out of the paint, ensuring a clean application every time.

Safety is a priority with the Graco 1050P, which comes with an easy-to-use pressure relief valve. This feature prevents accidental discharge of paint and enhances user protection while operating the sprayer.

In summary, the Graco 1050P is a feature-packed paint sprayer built for both performance and convenience. Its powerful motor, airless technology, portability, and versatile design make it a top choice for any painting professional or DIYer looking to achieve flawless results.
Top Page Image Contents