Harman-Kardon AVR 510 Reassigning Device Control Selectors, Resetting the Remote Memory

Page 40

Programming the Remote

Reassigning Device Control Selectors

Although each Input Selector e is normally assigned to the category of product shown on the remote, it is possible to reassign one of these but- tons to operate a second device of another type. For example, if you have two VCRs but no satellite receiver, you may program the “SAT” button to operate a second VCR. Before following the nor- mal programming steps for either Three-Digit entry or Auto Search code entry, you must first reassign the button with the following steps:

1.Press the Input Selector e you wish to reassign and the Mute button 38 at the same time until the red light appears under the Input Selector e and the Program/SPL Indicator c flashes amber.

2.Press the Input Selector e for the device you wish to program into the reassigned button.

3.Enter the three-digit code for the specific model you wish the reassigned button to operate.

4.Press the same Input Selector e pressed in Step 1 once again to store the selection. The red LED under the re-assigned Input Selector will flash three times and then go out.

Example: To use the CBL/SAT button to oper- ate a second VCR, first press the CBL/SAT Input Selector e and the Mute button

38 at the same time until the red light glows under the CBL/SAT e button. Press the VCR e button, followed by the three-digit code for the specific model you wish to control. Finally, press the CBL/SAT e button again.

Resetting the Remote Memory

As you add components to your home-theater sys- tem, occasionally you may wish to totally repro- gram the remote control without the confusion of any commands, macros or ”Punch-Through“ pro- gramming that you may have done. To do this, it is possible to reset the remote to the original factory defaults and command codes by following these steps. Note, however, that once the remote is reset, all commands or codes that you have entered will be erased and will need to be re- entered:

1.Press any of the Input Selector buttons e and the ”O“ button r at the same time until the Program/SPL Indicator c begins to flash amber.

2.Press the ”3“ button r three times.

3.The red LED under the Input Selector e will go out and the Program/SPL Indicator c will stop flashing and turn green.

4.The Program/SPL Indicator c will remain green until the remote is reset. Note that this may take a while, depending on how many commands are in the memory and need to be erased.

5.When the Program/SPL Indicator c goes out, the remote has been reset to the factory settings.

40PROGRAMMING THE REMOTE

Image 40
Contents AVR 510 Audio/ Video Receiver AVR 510 Audio/ Video Receiver Description and Features IntroductionWhile complex digital systems are hard Multiple Digital Inputs and OutputsImportant Safety Information Safety InformationUnpacking Front Panel Controls Set Button  Input Indicators Ò Delay# Digital Optical 3 Input Preset Stations Selector Press this Main Information Display Û into the AVR 510’s memoryNight Mode Indicator This indicator Front Panel Information DisplayFor more information on the Channel Indicators Rear Panel Connections Rear Panel Connections Main Remote Control Functions AVR SelectorMain Remote Control Functions Dialog center channel intelligibility at low volume levels` Preset Up/Down When the tuner is 37 6-Ch. Direct Input Press this buttonTo select the component connected to Channel Direct Input ª as the sourceZone II Remote Control Functions Between the AM and FM bandsInstallation and Connections System InstallationAudio Equipment Connections Connect the analog output of a CD player to the CD inputsSystem and Power Connections Video Equipment ConnectionsVideo Connection Notes Multiroom IR LinkAC Power Connections External Audio Power Amplifier ConnectionsExternal Audio Decoder Connection System Configuration Speaker Selection and PlacementSpeaker Placement System SetupUsing the On-Screen Display Plug the AC Power Cord into an unswitched AC outletSetting the System Configuration Memories Surround Setup Input SetupOr the ⁄/¤ buttons n on the remote Delay Settings Buttons on the remote will take you to the delay settingsNight Mode Settings Speaker Setup SurroundIf no subwoofer is connected to Output Level AdjustmentInformation Display Y Manual Output Level Adjustment Using EzSetAVR 510 off using the Main Power Switch Additional Input Adjustments Basic Operation OperationSource Selection Surround Mode Chart Surround Mode Selection Digital Audio PlaybackSelecting a Digital Source Dolby DigitalAddition to the bitstream indicators, Digital Status IndicatorsNight Mode PCM Audio Playback Tuner OperationMP3 Audio Playback Output Level Trim Adjustment Preset TuningRecalling Preset Stations Volume Control Ó 34 îMemory Backup Channel Direct InputAdvanced Features Turn-On Volume LevelSemi-OSD Settings Display Brightness AVR 510’s Main Information DisplayFull-OSD Time-Out Adjustment Multiroom Setup InstallationMultiroom Operation Multiroom OperationProgramming the Remote Programming the RemoteErasing Learned Codes Learning CodesMacro Programming Erasing Macro Commands Mode Selector/Channel Down button kPress the AVR Selector f Programmed Device FunctionsChannel Control Punch-Through Volume Punch-ThroughTransport Control Punch-Through Resetting the Remote Memory Reassigning Device Control SelectorsFunction List Preset Up Preset DownTune Up DirectSetup Code Table TV 084 001 011 030 033 042 044 100 107 115 154 160 167 168175 176 021 031Setup Code Table VCR 159 057 058147 166 070 074 078 086 114 125 150 167 172Setup Code Table CD 037 038 045 046 171 175 202 203 020 036 056 057 064 065 089 090 091 092 096 099 104 212015 075 109 119 158 183 204 039 051 138 149 209Setup Code Table Tape Setup Code Table AudioSetup Code Table DVD Setup Code NumberSetup Code Table SAT Setup Code Table CBL 111 112 213 053 214055 056 061 099 100 101 207 063 115Troubleshooting Guide Processor ResetInformation from nonencoded programs Lights, motors or other electrical appliancesPage Technical Specifications Harman Kardon, Incorporated Part No. J90200012000

AVR 510 specifications

The Harman-Kardon AVR 510 is a high-performance AV receiver that has garnered attention for its impressive sound quality and versatile functionality. As part of Harman Kardon's esteemed line of audio equipment, the AVR 510 is designed to elevate the home entertainment experience, making it a favored choice for audiophiles and casual listeners alike.

One of the standout features of the AVR 510 is its powerful amplification system. With a robust output of up to 75 watts per channel, the receiver can drive a variety of speaker configurations, ensuring clear and dynamic sound across the frequency spectrum. This capability allows users to enjoy an immersive audio experience whether they are watching movies, playing video games, or listening to music.

The AVR 510 also supports multiple surround sound formats, including Dolby Digital and DTS. This enables users to experience rich, cinematic soundscapes that enhance the overall viewing experience. The inclusion of advanced processing technologies ensures that audio playback is accurate, highlighting the nuances in sound that make movies and music come alive.

Connectivity is another key aspect of the AVR 510, featuring a range of input options to accommodate various devices. With several HDMI inputs, digital optical and coaxial inputs, as well as analog audio connections, this receiver can seamlessly integrate with Blu-ray players, gaming consoles, and streaming devices. It also includes an AM/FM tuner, allowing users to enjoy their favorite radio stations.

The user interface of the AVR 510 is designed for convenience, featuring an intuitive on-screen menu that guides users through setup and operation. The inclusion of a remote control further enhances usability, allowing for easy access to settings and adjustments from across the room.

Additionally, the AVR 510 is equipped with Harman Kardon's proprietary technologies, such as Halosonic processing, which optimizes sound quality for various listening environments. This ensures that users can enjoy consistent audio performance regardless of their room's acoustics.

In conclusion, the Harman-Kardon AVR 510 stands out as a versatile and powerful AV receiver that enhances home entertainment through its detailed sound reproduction, robust connectivity options, and user-friendly design. Whether for serious movie watching or casual music listening, the AVR 510 delivers an exceptional audio experience that is hard to match.