Harman-Kardon Comprehensive Guide to AVR 435 and Harman Kardon 435 System Configuration and Setup

Page 26

System Configuration

Manual Setup

In most cases it is simpler, easier and more accu- rate to let EzSet/EQ take care of entering the sys- tem parameters for speaker “size”, speaker crossover, channel output and individual channel delay time. However, if you feel that your listen- ing room or system components are best suited to manual entry of these settings, the AVR 435 also allows you to enter or trim any of these tra- ditional system parameters. Even if you do make the settings manually, we recommend that you run the EzSet/EQ tests first so that a baseline set- ting is established, and then make your adjust- ments from there. Note that once EzSet/EQ has been run you do not need to adjust all system settings, only those that you want to adjust.

To view or change the current settings, press the OSD Button Lon the remote to bring up the MASTER MENU (Figure 1). Next, press the ¤ Navigation Button Eas needed until the cursor is on the MANUAL SETUP line. Press the Set Button Fto view the MANUAL SETUP menu (Figure 8).

* M A N U A L S E T U P *

E Z S E T E Q : O F F O N E Z S E T A D J U S T

S P E A K E R S I Z E

S P E A K E R X O V E R

D E L A Y A D J U S T

C H A N N E L A D J U S T

B A C K T O M A S T E R M E N U

Figure 8

If you have already run the EzSet/EQ calibration system, the first line of the menu enables you to hear the difference between the settings estab- lished by EzSet/EQ. The default setting is ON, which plays the incoming source with the EzSet/EQ settings. To hear the system in a Bypass mode, with none of the equalization filters in the circuit path, press the / Navigation Button

Eso that OFF is highlighted. Note that once changed, this setting will remain until you change it again in this menu. While you may want to use this menu option to hear the differ- ence that EzSet/EQ makes, we recommend that you leave the setting on to take advantage of the benefits of EzSet/EQ’s advanced room correction technology.

The EZSET ADJUST line on the menu enables you to set the system’s Tilt, or high-fre- quency boost. To make this adjustment, first make sure that EZSET EQ line is set to ON, as this item is not available when EzSet EQ is not in the signal path. When the cursor is on the EZSET ADJUST line, press the Set Button F, and then press the / Navigation Button Eto enter the desired setting. When you have completed your adjustment, press the Navigation Button Eto move the cursor

down to the BACK TO MANUAL SETUP line and press the Set Button F.

Note on Manual Setup Menus: Each of the four major manual setup menus (Speaker Size, Speaker Crossover, Delay Adjust and Channel Adjust) includes a line that reads EZSET SETTINGS. When the default setting of OFF is shown you are able to make any required adjustments that are available on that menu. However, you may change the setting to ON at any time to recall the settings established when EzSet/EQ was last run. It is also important to note that when the EzSet/EQ settings are in use, the AVR will not allow any changes to be made. To trim the settings press the / Navigation Button Euntil the cursor is on the EZSET SETTINGS line on the menu in use and press the / Navigation Button E to change the setting to OFF. This will allow you to make changes to the settings on that menu.

Speaker Setup

Although using EzSet/EQ to enter the settings for speaker “size” and crossover point, you may wish to make changes to those settings, or to manually enter a complete speaker profile for your system. In addition, for systems where you with to have separate speaker configuration set- tings for each input, rather than use the same settings for all inputs, you may also configure that option in these menus. Two separate menus are used to enter this information, and you may change the data on either or both, as needed.

The SPEAKER SIZE menu tells the AVR about the bass reproduction capabilities of your speakers. This, in turn, determines which speakers receive bass information that is derived from audio tracks or specifically intended for reproduc- tion by low-frequency-capable speakers by the use of a low-frequency effects (“LFE”) channel in digital program sources. In addition, by telling the AVR whether speakers are available for the Surround Back channels, the information on this menu is used to determine which surround modes may be used (e.g., modes such as Dolby Digital EX, Dolby Pro Logic IIx, or DTS-ES, requir- ing SBL/SBR speakers, are only available when a speaker is present in those channels).

The SPEAKER X-OVERmenu is used to further tailor the bass management system by determining the frequencies at which bass infor- mation is sent to a specific speaker position. This menu also contains settings to route LFE infor- mation and to set the subwoofer high-pass filter order.

To configure the speakers in your system for use with the AVR 435, or to check the settings entered by EzSet/EQ, check the settings on the various sub-menu groups on the MANUAL SETUP menu, starting with the SPEAKER SIZE menu (Figure 9) and then check the other menus’ settings. To do this, go to the Manual Setup Menu (Figure 8) by first pressing the OSD Button Lto recall the Master Menu (Figure 1). Next, press the / Navigation Button Euntil the cursor is on the MANU- AL SETUP line on the menu in use and press the Set Button F. When the MANUAL SETUP Menu is shown, press the / Navigation Button Eagain until the cursor is on the SPEAKER SIZE line and press the Set Button F.

* S P E A K E R S I Z E *

L E F T / R I G H T : S M A L L

C E N T E R

:

S M A L L

 

S U R R O U N D :

S M A L L

 

S U R R B A C K :

N O N E M A I N

S U B

M O D E :

S U B

 

S U B

S I Z E :

1 0 i n / 2 5 0 m m

E Z S E T S E T T I N G S : O F F O N

B A C K T O M A N U A L S E T U P

Figure 9

On the SPEAKER SIZE menu (Figure 9), you will see either the factory default settings or, if EzSet/EQ has been run, the settings recorded by the test results. In the case for the main speaker channels, each speaker position (front left/right, center, surround left/right and surround back left/right) you have the option of telling the system if the speakers used are “small” or “large”. These descriptions do not describe the actual physical size of the speakers, but rather refer to the type of speaker. For each of these settings, select LARGE when the speakers in a particular position are traditional full-range loud- speakers. Use the SMALL setting for smaller, frequency-limited “satellite” speakers that do not reproduce sounds below 60Hz. In all cases except the front left/right speakers you may also select NONE. This tells the system that no speakers are present at the particular position, allowing the AVR to select the correct surround modes that are compatible with the number of speakers installed. For example, in order to use the Dolby Digital EX, Dolby Pro Logic IIx, DTS-ES Logic 7/7-channel and 7 Stereo modes, you must have either Large or Small speakers entered as the setting for the Surround Back channels.

26SYSTEM CONFIGURATION

Image 26
Contents Power for the Digital Revolution AVRTable of Contents Declaration of ConformityIntroduction Description and FeaturesAVR 435’s power simple to use Zone II remote is includedUnpacking Introduction / Safety InformationImportant Safety Information Front Panel Controls To select between the Optical Coaxial ÓMore information Rear Panel Connections Digital Audio Outputs Connect theseUnswitched Outlet Switched Outlet AC Power Cord Jack Connect the ACRemote IR Carrier Output The output AVR 435 when appropriate upgrades are available+ and negative terminals Main Remote Control Functions Light ButtonMain Remote Control Functions Channel Direct Inputs the inputMain Remote Control Functions Main Remote Control Functions ∆ Play Forward/Reverse/Stop K Mute Zone II Remote Control FunctionsMulti IR input jack Infrared sensor that is connected to the AVR’sVideo Equipment Connections Installation and ConnectionsAudio Equipment Connections Video Connection Notes Scart A/V ConnectionsAny of the Video Audio Inputs Important Note for Adapter CablesIf you use a unit providing RGB signals on a Important Note for the Use SCART-Cinch AdaptersSystem and Power Connections Speaker Placement Speaker SelectionSystem Setup System ConfigurationUsing the On-Screen Display Input Setup‹/ › Navigation Button Eso that OUT Audio SetupInput Select Button ÛGon the front panel Press the ⁄/¤ Navigation Button EandBack T O Main Menu line and press the Set Button F Surround SetupSo that the cursor is next to Using EzSet/EQ Night Mode SettingsC K N E a R E L D C K M a S T E R M E N U Manual Setup Speaker SetupSurround Speaker Crossover Setting Delay Settings Once to move to the next lineManual Setup menu Output Level AdjustmentWhen the delay settings are complete, press Button on the remoteVolume until you can hear the test noise clearly On the remoteAdditional Input Adjustments Surround Mode Chart OperationMix of the in-phase material of the left and right channels Delay time not adjustableNo delay available DTS Neo6 MusicSource Selection Controls and Use of HeadphonesBasic Operation Channel/8-Channel Direct InputDolby Digital Surround Mode SelectionDigital Audio Playback MP3 Audio Playback Rear panelPCM Audio Playback Or front panel *ÓSelecting a Digital Source Digital Bitstream IndicatorsSpeaker/Channel Indicators Tape Recording Night ModeAudio, while the main feature is available Puts for Tape OutputsNormal output level adjustment for Output Level Adjustment With Source SignalsMemory Backup Dim FunctionSemi-OSD Settings Advanced FeaturesTurn On Volume Level Front-Panel-Display FadeDigital Auto-Poll Settings Advanced Features / Multiroom OperationFull-OSD Time Out Adjustment Multiroom OperationMultiroom Operation Surround Amplifier Channel AssignmentMultiroom Operation / Tuner Operation Basic Tuner OperationRDS Operation RDS TuningTuner Operation RDS Display OptionsAppears Configuring the RemotePreprogrammed Code Entry Fappears Learning CommandsAutomatic Code Entry Device Priority Programming the RemoteLearning Codes for an Input Selector Changing DevicesWill scroll to its right. For example, press Macro ProgrammingRecording a Macro At the next menu screen press Power On VID 2/TV VID 3/Cable AVR Logic 7 OErasing a Macro Read a MacroReturning the Volume Control Settings to Default Operation Punch-Through ConfigurationVolume Punch-Through Red. Press the ⁄¤ Navigation ButtonsTransport Punch-Through Returning the Channel Control Settings to Default OperationRenaming Record Pand Skip Up/Down‹/› Navigation Buttons Eas required Renaming Individual KeysAt this point you have two options Resetting the RemoteBacklight Options See page 34 for more informationAdditional Notes on Configuring and Operating the Remote Power Switch 1 is pushed Troubleshooting GuideProcessor Reset Press the AVR SelectorTechnical Specifications Harman Consumer Group International

AVR 435 specifications

The Harman-Kardon AVR 435 is a versatile and powerful home theater receiver that has made a significant mark in the world of audio-visual entertainment. Known for its impressive audio quality and advanced features, this unit caters to both casual listeners and audiophiles looking for a rich experience.

At the heart of the AVR 435 is its 7.1 channel configuration, providing a robust sound system that envelops listeners in an immersive audio experience. Each channel is powered by high-performance amplifiers, delivering a total output of 100 watts per channel. This ensures dynamic sound reproduction, whether you are watching movies, playing games, or listening to music.

One of the standout features of the AVR 435 is its support for various surround sound formats, including Dolby Digital, DTS, and Dolby Pro Logic II. This enables the receiver to decode multiple audio streams, producing an authentic surround sound experience. The inclusion of Harman-Kardon's proprietary Logic 7 processing further enhances the spatial sound, making it particularly effective for movie watching and multi-channel music.

The AVR 435 also boasts extensive connectivity options. With multiple HDMI inputs, digital audio inputs, and component video inputs, it facilitates easy connection to a wide range of devices such as Blu-ray players, gaming consoles, and streaming devices. This flexibility ensures that users can integrate their home theater system seamlessly.

Moreover, the receiver features a built-in AM/FM tuner, allowing access to a variety of radio stations, and provides pre-set options for user convenience. An intuitive on-screen setup guide makes configuration simple, allowing users to adjust settings according to their personal preferences.

Another notable characteristic is the inclusion of a room EQ feature, which helps optimize sound performance based on the specific acoustics of your space. This ensures that users receive the best possible audio quality regardless of their room layout.

The design of the AVR 435 emphasizes both style and functionality. Its sleek, modern aesthetic fits seamlessly into any home decor, while the layout of controls is user-friendly. Whether using the remote control or the front panel, navigating through the various functions is straightforward.

In conclusion, the Harman-Kardon AVR 435 represents a powerful blend of sound quality, advanced technology, and user-friendly features. It stands as a solid choice for anyone eager to create an exceptional home theater experience.