Harman-Kardon AVR 435 owner manual Technical Specifications

Page 57

Technical Specifications

Audio Section

Stereo Mode

Continuous Average Power (FTC)

80 Watts per channel, 20Hz–20kHz,

@ < 0.07% THD, both channels driven into 8 ohms

5/7 Channel Surround Modes

Power Per Individual Channel

Front L&R channels:

65 Watts per channel,

@ < 0.07% THD, 20Hz–20kHz into 8 ohms

Center channel:

65 Watts, @ < 0.07% THD, 20Hz–20kHz into 8 ohms

Surround (L & R Side, L & R Back) channels: 65 Watts per channel,

@ < 0.07% THD, 20Hz–20kHz into 8 ohms

Input Sensitivity/Impedance

 

Linear (High Level)

200mV/47kohms

Signal-to-Noise Ratio (IHF-A)

95dB

Surround System Adjacent Channel Separation

Analog Decoding

40dB

(Pro Logic, etc.)

 

Dolby Digital (AC-3)

55dB

DTS

55dB

Frequency Response

 

@ 1W (+0dB, –3dB)

10Hz– 130kHz

High Instantaneous

 

Current Capability (HCC)

±40 Amps

Transient Intermodulation

 

Distortion (TIM)

Unmeasurable

Rise Time

16 µsec

Slew Rate

40V/µsec**

Supplied Accessories

The following accessory items are supplied with the AVR 435.

If any of these items are missing, please contact Harman Kardon customer service at www.harmankardon.com.

A system remote control

A Zone II remote control

An microphone

Extender rod for microphone

An AM loop antenna

An FM wire antenna

Six AAA batteries

FM Tuner Section

 

Frequency Range

87.5 –108MHz

Usable Sensitivity

IHF 1.3 µV/13.2dBf

Signal-to-Noise Ratio

Mono/Stereo: 70/68dB (DIN)

Distortion

Mono/Stereo: 0.15/0.2%

Stereo Separation

40dB @ 1kHz

Selectivity

±400kHz: 70dB

Image Rejection

80dB

IF Rejection

90dB

AM Tuner Section

 

Frequency Range

520–1710kHz

Signal-to-Noise Ratio

45dB

Usable Sensitivity

Loop: 500µV

Distortion

1kHz, 50% Mod: 0.8%

Selectivity

±10kHz: 30dB

Video Section

 

Video Format

PAL/NTSC

Input Level/Impedance

1Vp-p/75 ohms

Output Level/Impedance

1Vp-p/75 ohms

Video Frequency Response

 

(Composite and S-Video)

10Hz–8MHz (–3dB)

Video Frequency

 

Response (Component)

10Hz-50MHz (-3dB)

General

 

Power Requirement

AC 220-240V/50Hz

Power Consumption

59W idle, 1040W maximum

 

(7 channels driven)

Dimensions (Max)

 

Width

440mm

Height

165mm

Depth

435mm

Weight

17.7 kg

Depth measurement includes knobs, buttons and terminal connections.

Height measurement includes feet and chassis.

All features and specifications are subject to change without notice.

Harman Kardon and Power for the Digital Revolution are registered trademarks of Harman International Industries, Incorporated.

is a trademark of Harman International Industries, Inc. (Patent No. 5,386,478).

*Manufactured under license from Dolby Laboratories.

“Dolby,” “Pro Logic,” “Pro Logic II,” "Pro Logix IIx" and the Double-D symbol are trademarks of Dolby Laboratories. Confidential Unpublished

Works. ©1992–1999 Dolby Laboratories, Inc. All rights reserved.

DTS and DTS Surround, DTS-ES and DTS Neo:6 are trademarks of Digital Theater Systems, Inc.

Logic 7 is a registered trademark of Harman International Industries, Incorporated.

A-BUS and A-BUS Ready are registered trademarks of Leisure Tech Electronics Pty Ltd Australia.

TiVo is a registered trademark of TiVo, Inc.

Replay TV is a registered trademark of Digital Networks North America, Inc.

**Without input anti slewing and output isolation networks.

TECHNICAL SPECIFICATIONS 57

Image 57
Contents AVR Power for the Digital RevolutionDeclaration of Conformity Table of ContentsAVR 435’s power simple to use Description and FeaturesIntroduction Zone II remote is includedIntroduction / Safety Information Important Safety InformationUnpacking Front Panel Controls Coaxial Ó More informationTo select between the Optical Digital Audio Outputs Connect these Rear Panel ConnectionsSwitched Outlet AC Power Cord Jack Connect the AC Unswitched OutletAVR 435 when appropriate upgrades are available + and negative terminalsRemote IR Carrier Output The output Light Button Main Remote Control FunctionsChannel Direct Inputs the input Main Remote Control FunctionsMain Remote Control Functions Main Remote Control Functions Multi IR input jack Zone II Remote Control Functions∆ Play Forward/Reverse/Stop K Mute Infrared sensor that is connected to the AVR’sInstallation and Connections Audio Equipment ConnectionsVideo Equipment Connections Any of the Video Audio Inputs Scart A/V ConnectionsVideo Connection Notes Important Note for Adapter CablesImportant Note for the Use SCART-Cinch Adapters If you use a unit providing RGB signals on aSystem and Power Connections Speaker Selection Speaker PlacementUsing the On-Screen Display System ConfigurationSystem Setup Input SetupInput Select Button ÛGon the front panel Audio Setup‹/ › Navigation Button Eso that OUT Press the ⁄/¤ Navigation Button EandSurround Setup So that the cursor is next toBack T O Main Menu line and press the Set Button F Night Mode Settings Using EzSet/EQC K N E a R E L D C K M a S T E R M E N U Speaker Setup Manual SetupSurround Speaker Crossover Setting Once to move to the next line Delay SettingsWhen the delay settings are complete, press Output Level AdjustmentManual Setup menu Button on the remoteOn the remote Volume until you can hear the test noise clearlyAdditional Input Adjustments Operation Surround Mode ChartNo delay available Delay time not adjustableMix of the in-phase material of the left and right channels DTS Neo6 MusicBasic Operation Controls and Use of HeadphonesSource Selection Channel/8-Channel Direct InputSurround Mode Selection Digital Audio PlaybackDolby Digital PCM Audio Playback Rear panelMP3 Audio Playback Or front panel *ÓDigital Bitstream Indicators Speaker/Channel IndicatorsSelecting a Digital Source Audio, while the main feature is available Night ModeTape Recording Puts for Tape OutputsMemory Backup Output Level Adjustment With Source SignalsNormal output level adjustment for Dim FunctionTurn On Volume Level Advanced FeaturesSemi-OSD Settings Front-Panel-Display FadeFull-OSD Time Out Adjustment Advanced Features / Multiroom OperationDigital Auto-Poll Settings Multiroom OperationSurround Amplifier Channel Assignment Multiroom OperationBasic Tuner Operation Multiroom Operation / Tuner OperationTuner Operation RDS TuningRDS Operation RDS Display OptionsConfiguring the Remote Preprogrammed Code EntryAppears Learning Commands Automatic Code EntryFappears Learning Codes for an Input Selector Programming the RemoteDevice Priority Changing DevicesMacro Programming Recording a MacroWill scroll to its right. For example, press Erasing a Macro Power On VID 2/TV VID 3/Cable AVR Logic 7 OAt the next menu screen press Read a MacroVolume Punch-Through Punch-Through ConfigurationReturning the Volume Control Settings to Default Operation Red. Press the ⁄¤ Navigation ButtonsRenaming Returning the Channel Control Settings to Default OperationTransport Punch-Through Record Pand Skip Up/DownRenaming Individual Keys ‹/› Navigation Buttons Eas requiredBacklight Options Resetting the RemoteAt this point you have two options See page 34 for more informationAdditional Notes on Configuring and Operating the Remote Processor Reset Troubleshooting GuidePower Switch 1 is pushed Press the AVR SelectorTechnical Specifications Harman Consumer Group International

AVR 435 specifications

The Harman-Kardon AVR 435 is a versatile and powerful home theater receiver that has made a significant mark in the world of audio-visual entertainment. Known for its impressive audio quality and advanced features, this unit caters to both casual listeners and audiophiles looking for a rich experience.

At the heart of the AVR 435 is its 7.1 channel configuration, providing a robust sound system that envelops listeners in an immersive audio experience. Each channel is powered by high-performance amplifiers, delivering a total output of 100 watts per channel. This ensures dynamic sound reproduction, whether you are watching movies, playing games, or listening to music.

One of the standout features of the AVR 435 is its support for various surround sound formats, including Dolby Digital, DTS, and Dolby Pro Logic II. This enables the receiver to decode multiple audio streams, producing an authentic surround sound experience. The inclusion of Harman-Kardon's proprietary Logic 7 processing further enhances the spatial sound, making it particularly effective for movie watching and multi-channel music.

The AVR 435 also boasts extensive connectivity options. With multiple HDMI inputs, digital audio inputs, and component video inputs, it facilitates easy connection to a wide range of devices such as Blu-ray players, gaming consoles, and streaming devices. This flexibility ensures that users can integrate their home theater system seamlessly.

Moreover, the receiver features a built-in AM/FM tuner, allowing access to a variety of radio stations, and provides pre-set options for user convenience. An intuitive on-screen setup guide makes configuration simple, allowing users to adjust settings according to their personal preferences.

Another notable characteristic is the inclusion of a room EQ feature, which helps optimize sound performance based on the specific acoustics of your space. This ensures that users receive the best possible audio quality regardless of their room layout.

The design of the AVR 435 emphasizes both style and functionality. Its sleek, modern aesthetic fits seamlessly into any home decor, while the layout of controls is user-friendly. Whether using the remote control or the front panel, navigating through the various functions is straightforward.

In conclusion, the Harman-Kardon AVR 435 represents a powerful blend of sound quality, advanced technology, and user-friendly features. It stands as a solid choice for anyone eager to create an exceptional home theater experience.