GE 71722 warranty How To Maintain, Cleaning the Carpet Shampooer/Extractor’s Suction Cover

Page 16

How To Maintain

NOTE: Turn off the power switch and unplug the electrical cord to service cleaning nozzles.

C. Cleaning the Carpet Shampooer/Extractor’s Suction Cover

Suction Cover

1.	Remove the screws from each
	side of the suction cover.
2.	Lift the suction cover off and
	clean the area of dirt and lint.
3.	Replace the suction cover by
Tabs	sliding the tabs on top of the
	suction cover into the top slots
	on the hood. Make sure the
	suction cover gasket is in place
	on the unit before replacing
	cover.
4.	Align one of the screw holes in
	the suction cover, hood and base
	then secure with screw. Also
	complete this step for second
	screw hole.
Suction Cover Gasket
(around rim of suction
cover area on unit)

D.Cleaning the Carpet Shampooer/Extractor’s Plunger, Boot Seal and Filter

1.Remove the clean water solution tank.

2.Remove the Plunger, Boot Seal and Filter Assembly by lifting up the Boot Seal. This will pull out the Plunger, Boot Seal and Filter Assembly (see Figure 1).

3.Remove the Reservoir Filter and clean it by removing any debris and rinsing with water.

4.Reinsert the Filter on the Plunger stem and place the Assembly directly into the reservoir. Install this assembly into the reservoir by pressing down on the top of the plastic plunger. Do not press down on the rubber boot seal.

IMPORTANT! Make sure the plunger stem is placed into the hole in the bottom of the reservoir for a secure fit (see Figure 2).

5.Replace the Clean Water Solution Tank back onto the carpet shampooer/ extractor unit.

FIGURE 1

Plunger, Boot Seal and Filter Assembly

Boot Seal

Plunger Stem Assembly

Reservoir Filter

FIGURE 2

Correct installation

of assembly

16

Image 16

Contents Owner’s Guide Model Cleaner Safety Important SafeguardsGrounding Instructions Instructions Visant LA Mise À TerreCustomer Assistance General InformationRating Plate Carpet Shampooer/Extractor Parts How To Assemble Check Recovery TankAttach Handle Store Attachment HoseAfter Cleaning Preparing Carpet Before CleaningVacuum Carpet Fill the Clean Water Solution Tank Recovery Tank Emptying the Recovery TankAutomatic Shut-Off How To Use The Carpet Shampooer/Extractor Carpet CleaningOperating The Carpet Shampooer/Extractor Transporting the Carpet Shampooer/ExtractorTest clean a hidden area Fabric Code RatingsVacuum Upholstery or Stairs Check the stuffing material if possibleCleaning Solution Release Trigger Clean Water Solution Tank Maintenance How To Maintain The Carpet Shampooer/ ExtractorRecovery Tank Maintenance Cleaning the Carpet Shampooer/Extractor’s Suction Cover How To MaintainPlunger, Boot Seal and Filter Assembly How to Replace the Carpet Shampooer/Extractor’s Belt Placing the handle on the floorProblem Solving Cause Solution Authorized Appliance Parts Two-Year Limited Warranty Customer AssistanceGuía del propietario Modelo Puntos de Seguridad Importante Para SU SeguridadInstrucciones para la conexión de corriente a tierra PeligroAyuda al cliente Información GeneralInformación sobre la placa de datos Partes de la lavadora/exractora Como Armarla Acople la mangueraGuarde la manguera incluida como accesorio Guarde el cordón eléctricoLimpie la alfombra con la aspiradora Después de la limpiezaLlene el tanque de solución de agua limpia Tanque de recuperación Corte automáticoComo usar la lavadora/extractora para Alfombras Limpieza de alfombrasOperación de la lavadora/extractora para alfombras Cómo transportar la lavadora/extractora para alfombrasCategorías de telas Pase la aspiradora a los tapizados y escalonesRevise el material del relleno si es posible Pruebe limpiar un lugar que no se veTanque de Botón Solución de Selector Agua limpia Gatillo para Liberar la solución Mantenimiento del tanque de solución de agua limpia Mantenimiento del tanque de recuperaciónComo Hacerle Mantenimiento Ensamblaje del pistónCorrea del cepillo circular para modelos IlustracionResolviendo Problemas Ayuda al cliente Garantía Limitada de Dos Años