American Standard 6059.193 Mount Enclosure Fig, Connect Spout Hose to Enclosure Fig

Page 4

2MOUNT ENCLOSURE; Fig. 2

NOTE.The illustration shows the ICU FAUCET mounted on the American Standard ICU Sink. Faucet can be installed on almost any sink or countertop. For Faucet installation on the American Standard ICU Sink, see instruction sheet No. 7301793-100 (ICU Sink System) supplied with Sink for more detailed information.

1.For installation on ICU Sink mount ENCLOSURE (1) on MOUNTING BRACKET (2) with SCREWS (3).

2.For all other sinks or countertops determine location of ENCLOSURE (1). It must be located within the 14" (356mm) by 21" (533mm) shaded area shown in Figure 2 in order for electrical connections from the spout assembly to be completed.

NOTE: ENCLOSURE SUPPLY HOSE is 20". Distance between wall supply and ENCLOSURE (1) must be taken into consideration.

3.Remove 4 screws from COVER (6) and pull off COVER (6). Hold the ENCLOSURE (1) in desired location and mark the four mounting hole locations as shown. Fig. 2.

4.The ENCLOSURE (1) works best if secured to a wall stud or cross brace within the wall, using the SCREWS

(4) supplied. If the ENCLOSURE (1) is to be installed on a tile or plaster wall the ANCHORS (5) and SCREWS

(4) should be used. Fig. 2.

5.For installations on drywall or tiled walls; use ANCHORS (5) and SCREWS (4) for securing ENCLOSURE (1) to finished wall. Drill four 1/4" dia. holes a minimum of 1-3/4" deep. Insert the four ANCHORS (5) flush with face of the finished wall. Align the ENCLOSURE (1) and Install the MOUNTING SCREWS (4). Tighten to secure ENCLOSURE (1) to mounting surface.

3CONNECT SPOUT HOSE TO ENCLOSURE; Fig. 3

1.Connect SUPPLY NUT (1) from spout assembly to nipple on top of ENCLOSURE (2). Tighten with adjustable wrench to make a water tight connection. Fig. 3.

4CONNECT WATER SUPPLY TO ENCLOSURE AND WALL SUPPLY; Fig. 4

NOTE; If using the optional Mixing Valve See Sheet #M968808 for installation instructions.

1.Insert FIBER WASHER (4) into SUPPLY NUT (1) on ENCLOSURE (2).

2.Connect SUPPLY NUT (1) on ENCLOSURE (2) to FLEXIBLE SUPPLY HOSE (3).Tighten to make a water tight connection. Use two wrenches to tighten if necessary. Fig. 4.

3.Connect FLEXIBLE SUPPLY (3) directly to wall supply. Connection on FLEXIBLE SUPPLY (3) is 3/8" compression. Use adjustable wrench to tighten connection. Do not over tighten. Fig. 4a.

Note: FLEXIBLE SUPPLY (3) measures 20" from the bottom of the ENCLOSURE (1) base. If additional supply length is required, installer must purchase parts separately. Important: If FLEXIBLE SUPPLY (3) is too long, loop to avoid kinking.

Fig. 2

 

 

 

 

 

21"

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(533mm)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

14"

 

 

 

ENCLOSURE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(356mm)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MOUNTING

 

 

 

 

 

 

2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

HOLES

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2-3/4"

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MOUNTING

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(71mm)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

BRACKET

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SUPPLIES

3"

3-3/4"

 

 

 

 

 

 

 

WASTE

 

 

 

 

 

 

 

 

 

 

(76mm)

 

 

 

(96mm)

 

 

 

 

 

 

 

 

 

2MOUNTING

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5

 

 

 

 

 

 

 

 

 

 

 

 

 

BRACKET

 

 

 

 

 

 

 

 

 

 

 

 

4

 

 

 

 

 

 

3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

20"

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1524mm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(500mm)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(60)

1

NOTE: If using Mixing Valve (optional) See Sheet #M968808 for installation instructions.

Fig. 3

1

 

 

2

 

 

 

Fig. 4

2

1

 

DO NOT USE PIPE

 

 

 

 

SEALANT ON THREADS

4

3

Fig. 4a

OTHER SINK

INSTALLATION

4" ELECTRICAL BOX OR EQUIVALENT BY OTHERS

COLD WATER OR 3

TEMPERED

WALL SUPPLY

M 9 6 5 2 7 1

3

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Installation Instructions Unpacking GN SpoutInstallation Roughing-in DimensionsInstall Spout Assembly Fig Recommended ToolsConnect Spout Hose to Enclosure Fig Mount Enclosure FigConnect Water Supply to Enclosure and Wall Supply Fig Electrical Installation Electrical Connections FigUnit #1 Unit #2 Unit #3For AC-VERSION Multi HOOK-UPTest Installed Faucet MaintenanceHOW to Change Sensor Range Factory set at 6 Fig HOW to Clean Filter FigGeneral Cleaning Fig HOW to Clean and Remove the Flow Restrictor FigFaqs

6059.193 specifications

The American Standard 6059.193 is an innovative and stylish shower system that epitomizes modern design and functionality. Combining advanced technology with aesthetic appeal, this shower system is designed to enhance the bathing experience while ensuring durability and ease of use.

One of the key features of the American Standard 6059.193 is its sleek and ergonomic design. The system includes a contemporary showerhead, a luxurious hand shower, and a versatile tub spout, all crafted from high-quality materials that ensure longevity. The chrome finish not only gives a polished look but also prevents tarnishing, maintaining its beautiful appearance over time.

In terms of technology, the 6059.193 incorporates the latest in water-saving innovations. It is equipped with an efficient flow rate that complies with EPA WaterSense guidelines, delivering a satisfying spray while conserving water. This makes it an environmentally friendly choice that helps users reduce their water bills without sacrificing performance.

The shower system features a powerful yet adjustable spray pattern, allowing users to customize their experience. Whether one prefers a gentle mist or a more vigorous rainfall, the American Standard 6059.193 can easily accommodate different preferences. The hand shower is designed with a comfortable grip and an easy-to-use diverter, making it simple to switch between the showerhead and the hand shower.

Installation is made hassle-free with the well-thought-out design of the American Standard 6059.193. The system comes with clear instructions, and its universal compatibility allows it to fit seamlessly into most standard shower setups. This makes it an excellent choice for both new installations and upgrades.

Safety features have also been prioritized in this system. The thermostatic control prevents scalding by maintaining a consistent water temperature, enhancing user safety, especially for families with children. This careful attention to safety and user experience highlights American Standard’s commitment to quality.

In summary, the American Standard 6059.193 shower system combines modern aesthetics with advanced functionality, making it a standout choice for homeowners looking to upgrade their bathroom. With its emphasis on water conservation, customizable features, ease of installation, and commitment to safety, this shower system provides a spa-like experience that can transform any bathroom into a personal oasis.
Top Page Image Contents