Electro-Voice EVF-1181S, EVF-2121S, EVH-1152S, EVF-1152D, EVF-1122D EVF and EVH Rigging System cont’

Page 27

5.0 EVF and EVH Rigging System (cont’)

5.21Anatomy of an EVF or EVH Flying System Using M10 Eyebolts 5.211 Eyebolt Application Warnings

No eyebolt should be mounted in the sides of any EVF or EVH enclosure in order to suspend a system or cluster from the top.

Figure 16:

Eyebolts installed incorrectly in the sides of an enclosure in order to suspend it from above

Eyebolts must be fully seated and oriented in the plane of pull as shown in Figure 17. always use washers to distribute suspension loads. Refer to section 6.3 for specific eyebolt weight and angle restrictions.

Figure 17:

Illustration showing the use of washers with fully seated eyebolts,

with correct orientation in the plane of pull

Electro-Voice EVF/EVH User Manual

27

Image 27 Contents
Page Table of Contents Rigging-Safety Warning Table of Contents cont’Introduction EVF-1122S/96 example Introduction cont’End View Front View Side View 143.0 lb 64.9 kg 145.5 lb 66.1 kg Dimension Key suspension point dimensions as shown in figure aboveFinishes and Colors Available EVF Front-Loaded SeriesEVH Horn-Loaded Series Tool List Accessories for EVF and EVH SystemsGeneral Aiming and Placement Guidelines Designing an EVF/EVH ClusterDirectivity Break Frequency Defined Basic Clustering Guidelines Designing an EVF/EVH Cluster cont’Coverage-Uniformity Target Multiple-Source Interference in Clusters See text for more details NormalizedReducing Multiple-Source Interference EVF Full-Range Designing an EVF/EVH Cluster cont’ Preparing EVF and EVH Systems for Installation Recommended Preflight ProceduresPassive/Biamp Crossover Configuration Rotation of High-Frequency Waveguides EVF systems Preparing EVF and EVH Systems for Installation cont’Digital Signal Processing Full-Range Systems in Passive Mode Preparing EVF and EVH Systems for Installation cont’ VRK-1 or HRK-1 connection EVF and EVH Rigging SystemIntroduction Flying EV-Innovation EV-I Loudspeaker System VRK-1 or HRK-1 connection VRK-2 or HRK-2 connectionVRK-3 rigging kit with parts identified EVF and EVH Rigging System cont’VRK-1 rigging kit with parts identified VRK-2 rigging kit with parts identifiedHRK-1 rigging kit with parts identified HRK-2 rigging kit with parts identifiedHRK-3 rigging kit with parts identified EV-I Rigging Primer Important Details that Apply to the VRK and HRK Rigging KitsEVF and EVH Rigging System cont’ Eyebolt Installation All-Eyebolt Clusters Hardware not shown, using aTwo-system horizontal cluster using Systems, using a moderate trim angle Systems, using an extreme trim angleVRK Kits and Vertically Rigged Clusters HRK Kits and Horizontally Rigged Clusters EVF Full-Range Six-enclosure horizontal hang of three systems above Assembly Instructions for VRK and HRK kits Short in front Toward grille Working Load Limit and Safety-Factor Definitions Rigging-Strength Ratings and Safety FactorsStructural Rating Overview Rigging-Strength Ratings and Safety Factors cont’All-Eyebolt Structural Ratings Limits for ALL-EYEBOLT Clusters onlyWLL for M10 eyebolts in the EVI-M10K eyebolt kit Working Load Limits for EyeboltsLeft-to-Right All-Eyebolt Cluster Angles Suspension-Line AnglesVRK Rigging Structural Ratings for Vertical Clusters Limits for Vertical Clusters only WLL for M10 eyebolts in the EVI-M10K eyebolt kit Left-to-Right Vertical Cluster Angles Maximum load and maximum height for horizontal clusters HRK Rigging Structural Ratings for Horizontal ClustersTwo cluster using HRK rigging kits Using Tie Plates as Main Load-Bearing SuspensionSuspension-Line Angles for HRK Kits Symmetry for Horizontal Clusters using HRK Kits Left-to-Right Horizontal Cluster Angles Inner Connection PointsRatings for Outdoor Applications with Wind Loading Electro-Voice Structural-Analysis ProceduresRigging Inspections and Precautions Rigging Web sites ReferencesRigging printed Mechanical Engineering printedPage Page Electro-Voice
Related manuals
Manual 2 pages 29.71 Kb